B Series——Waterproof Model NC543 NC543W User Manual V1.
http://www.wansview.com Index 1 INTRODUCTION ...........................................................................................................................4 2 FUNCTION AND FEATURES .....................................................................................................4 3 APPEARANCE AND INTERFACE.............................................................................................5 4 5 6 7 3.1 APPEARANCE ...........................................................
http://www.wansview.com 7.4.4 Restore Factory Default.....................................................................................................21 7.4.5 User browsing Log.............................................................................................................21 8 CENTRALIZATION CONTROL ................................................................................................22 9 TECHNICAL PARAMETERS ......................................................................
http://www.wansview.com 1 Introduction The IP Camera combines a high quality digital video camera with network connectivity and a powerful web server to bring clear video to your desktop from anywhere on your local network or over the Internet. Your IP Camera package should contain the following items, If any of the listed items are missing, please contact your reseller from where you purchased the camera for assistance.
http://www.wansview.com 9 Alarming record can be sent by email, FTP server. It also sends alarm info to the alarm server. 9 Support three level of user authority. 9 Support upgrading online. 9 A free DDNS provided by manufacturer, and written in the device. 9 Manufacture provides free software, support Multi-view, Long time recording, video replay etc. 3 Appearance and interface 3.1 Appearance Figure 1 3.
http://www.wansview.com specification. 2) RJ45 Ethernet Socket: RJ45 Ethernet socket is 10/100M self-adjust. The equipment can connect to all kinds of network equipments, such as hub, router, switch, etc. NOTE: Factory setting IP is 192.168.0.178, the http port is 80, the username is admin, the password is 123456. 3) RESET Button: Press it and hold on more than 10 seconds, the equipment will restart and recover to the factory default settings. 4 Network Connecting Figure 3 4.
http://www.wansview.com getting the communication link fluency. 1) The PC and IP Camera are in the same LAN. If you want to use this PC to visit the IP Camera, you need to make sure their IP address is at the same segment. Otherwise you need to do the reset of the IP Camera’s IP address. For example, the IP Camera-1’s IP address in Figure 3 is 192.168.1.139 (at the segment of 192.168.1), while the PC-1’s IP address is 192.168.0.175 (at the segment of 192.168.
http://www.wansview.com Figure 4 If you have the firewall software in your PC, when you run the HSearch_en.exe, it may pop up a window to say if you want to block this program or not, then you should choose not to block. IP Camera by default use fixed IP address 192.168.0.178 and fixed http port 80. If you don’t have this software, you could also press down the reset button to go back the factory setting. Then you could use this defaulted IP address to visit the IP Camera.
http://www.wansview.com Figure 5 5.2 Visit IP Camera We suggest using IE kernel browser to view the video (it can provide more functions), but user need to install Player before viewing the video. Click “download and install player (first use)” link, it will popup dialogue box as Figure 6, click Run, it will automatically download player and install. Figure 6 After install the plug-ins, click “Mode 1 to view” link in Figure 5 to view the video (video as Figure 7).
http://www.wansview.com Figure 7 1) Menu column There are 2 kinds of menu, one is main menu, and the other is submenu. The main menu lies at the top of the interface, including View, Network, Alarm, Maintain; Submenu lies on the left of the interface, and different main menu is in line with different submenu. 2) Video Displaying Area Video display area is according with resolution, the higher resolution, and the larger display.
http://www.wansview.com These buttons mean start video, stop, monitor, talk, record and snapshot. Click button to choose the functions. 5) PTZ and video control If device has the Pan/Tilt, in Pan/Tilt control area, user can control the position according to the arrow sign: up, down, left, right, middle, horizontal cruise, vertical cruise, and stop etc. Means open IO output and Close IO output. User can also set the device resolution, brightness, contrast and other parameters. 6 Visit IP Camera from WAN 6.
http://www.wansview.com visited by them. If user wants to put several IP Cameras into WAN, every device should set the port forwarding. In order to distinguish these devices, every device should set a different port. If the port of the device is not 80, should add the port to IP address with colon to visit the IP Camera. Example: http://202.96.82.177:81. 6.
http://www.wansview.com Figure 10 The third party domain name is realized by analysis manner, the domain name will be displayed in the browser all the time when visit camera. If the port is not 80, the port number should be adding to the domain name with colon. Example: http://robbicam2.3322.org:81 7 Other Settings 7.1 Network Setting 7.1.1 Basic Network Setting The user can also enter the Basic Network Settings to set the IP address except using the search software. See below Figure 11. Figure 11 7.1.
http://www.wansview.com Figure 12 Note: When the device is connected both WIFI and wired, after it starts up, it will firstly connect to the wired network, if it can’t connect to it, then it will change to connect the wifi. The IP address and port is the same, either wireless or wired network. 7.1.3 ADSL Setting User could enable the ADSL Dialup according to the below Figure 13 (The Telecom Operators will assign the user name and password to you when you apply for ADSL service.
http://www.wansview.com 7.1.5 DDNS Setting Please refer to the content in 6.2. 7.2 Alarm Settings 7.2.1 Alarm Setting 1) Alarm Detect User can select the motion detect to enable monitor a certain area, if anything happens in that area, it will trigger the alarm. In the motion detect sensibility, the smaller the figure, the more sensitive it is. 2) Alarm Action After every trigger of alarm during the scheduled time, the device can trigger alarm in several ways. ¾ Send alarm info by email.
http://www.wansview.com 7.2.2 Mail Service Setting The device will send alarm email to the email address was filled in. Please do the mail settings properly fist, Figure 16 is a mail setting page for your reference. After the setting, please click save and test to check if it works properly. If have already set the mail server properly, user can tick to enable “Report Internet IP by mail”. After every restart, the device will send its Internet IP address to user’s email address.
http://www.wansview.com 7.2.3 FTP Service Setting Figure 17 When alarming, device will snap and send the image to FTP server, please make sure the FTP setting is correct. Above Figure 17 of FTP setting for your reference, click setting to store the setting info and click test to check the setting. After correct setting FTP server, you can use “upload Image Periodically” function. Even no alarm, device can also send the snap image to FTP periodically.
http://www.wansview.com 7.3 Advanced 7.3.1 User Setting There are three levels of authority; they are Administrator/Operator/Visitor. Administrator have the highest authority, it can do any change to the settings. Operator account only can operate the IP camera, can’t do changes to the settings, and please refers to Figure 20. Visitor account only can watch the video, can’t do any operation to the IP camera, and please refers to Figure 21.
http://www.wansview.com Figure 21 7.3.
http://www.wansview.com As Figure 22, User can maximum add 9 devices to view the device simultaneously. Click refresh button to check the device in the LAN. When click the device, will popup setting dialogue box and input the device info, as figure 23 and click save. After that, must click submit button to save. Figure 24 7.4 Maintain 7.4.1 Device Information Figure 24 7.4.
http://www.wansview.com 7.4.3 Firmware upgrade The device runs 2 kinds of programmer, one is system firmware, the other is application firmware. They could be upgraded separately. Figure 26 7.4.4 Restore Factory Default Click “Restore Factory Default”, it will pop up a dialogue to confirm if you really want to restore the factory default. After confirmation, the system will restore the factory default and reboot. 7.4.
http://www.wansview.com 8 Centralization Control Figure 28 IPCMonitor is a free software offered by factory, several devices on LAN and WAN can be browsed at the same time. The software also supports snap, video record, alarm and so on. The below Figure 28 is the interface. For more information, pls. refer to the <> in CD.
http://www.wansview.com Network Other Features Physical Index Software(PC Side) Basic Protocol TCP/IP、UDP/IP、HTTP、SMTP、FTP、DHCP、 DDNS、UPNP、NTP、PPPOE Other Protocol 802.
http://www.wansview.com 4) Can find equipment via search software, but can’t visit If the IP address of IP camera and PC is not in the same Network Segment, you should change them on the same Network Segment before visit. Network Segment is the first three number of IP address. If the IP address of PC is 192.168.0.100, so it can only visit the equipment which IP address is between 192.168.0.1~192.168.0.255.
http://www.wansview.com 11 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.