RF BridgeR2 User manual V1.
中 ⽂ SONOFF TECHNOLOGIES CO., LTD. 使⽤说明 1. 下载“易微联”APP 易 微 联 eWeLink Android™ & iOS 2. 上电 433MHz RF Bridge 通电后,设备⾸次使⽤,默认进⼊快速配⽹模式(Touch)。Wi-Fi指⽰灯呈“两短⼀⻓闪烁”。 三分钟内没有进⾏配⽹,设备将退出快速配⽹模式(Touch)。如需再次进⼊,⻓按配对按钮 5秒直到Wi-Fi指⽰灯呈“两短⼀⻓闪烁”即可。 3.
中 文 SONOFF TECHNOLOGIES CO., LTD.
中 文 SONOFF TECHNOLOGIES CO., LTD.
中 文 SONOFF TECHNOLOGIES CO., LTD. 恢复出⼚设置 ⻓按配对按钮5秒直到Wi-Fi指⽰灯呈“两短⼀⻓闪烁”再松开,此时设备重置成功,默认 进⼊快速配⽹模式(Touch)。 更换新的⽹络环境使⽤时,需要恢复出⼚设置,再重新进⾏⽹络连接。 常⻅问题 问:设备添加成功后,显示离线,无法控制? 答:设备刚添加成功后,需要1-2分钟时间连接您的路由器并连网。如果长时间还是显示不 在线,请根据Wi-Fi指示灯的状态来判断: 1. 蓝灯2秒快闪一下:说明设备没有连上您的Wi-Fi。 ① 可能是Wi-Fi密码输入不正确. ② 可能是设备离您的路由器太远,信号太弱,或环境有干扰。请先将设备靠近路由器,如无改 善,重新添加一遍. ③ 设备不能识别5G的Wi-Fi,请选择2.4G的Wi-Fi重新添加. ④ 检查您的路由器后台是否开启MAC地址过滤,如有,请关闭。 如果以上均尝试不能解决,请用一部手机开启个人热点,尝试重新添加。 2.
English SONOFF TECHNOLOGIES CO., LTD. Operating Instruction 1. Download “eWeLink”APP eWeLink eWeLink Android™ & iOS 2. Power on 433MHz RF Bridge After powering on, the device will enter the quick pairing mode (Touch) during the first use. The Wi-Fi LED indicator changes in a cycle of two short and one long flash. The device will exit the quick pairing mode (Touch) if not paired within 3mins.
English SONOFF TECHNOLOGIES CO., LTD. Compatible Pairing Mode If you fail to enter Quick Pairing Mode (Touch), please try “Compatible Pairing Mode ” to pair. 1 2 Long press Pairing button for 5s until the Wi-Fi LED indicator changes in a cycle of two short flashes and one long flash and release. Long press Pairing button for 5s again until the Wi-Fi LED indicator flashes quickly. Then, the device enters Compatible Pairing Mode. Tap “+” and select “Compatible Pairing Mode ” on APP.
English SONOFF TECHNOLOGIES CO., LTD. Product Introduction RF LED indicator(Red) Wi-Fi LED indicator(Blue) Input 433MHz RF Bridge Pairing button The device weight is less than 1 kg. The installation height of less than 2 m is recommended.
English SONOFF TECHNOLOGIES CO., LTD. Factory Reset Long press the pairing button for about 5s until the Wi-Fi LED indicator changes in a cycle of two short and one long flash and release, then the reset is successful. The device enters quick pairing mode (Touch). Please reset the device to factory defaults if you want to change the Wi-Fi network, then reconnect the new network. Common Problems Q: Why my device stays “Offline”? A: The newly added device needs 1 – 2mins to connect Wi-Fi and network.
FCC Warning SONOFF TECHNOLOGIES CO., LTD. FCC Warning Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type RF BridgeR2 is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://sonoff.tech/usermanuals For CE RED: TX Frequency WiFi: 2412-2472MHz SRD: 433MHz RX Frequency WiFi: 2412-2472MHz SRD: 433MHz Output Power 802.11 b: 15.67dBm 802.11 n20: 10.91dBm 802.11 g: 5.93dBm SRD: -8.52dBm Shenzhen Sonoff Technologies Co., Ltd.