User's Guide

1 2
Reset
Wearing methods
English English
English English
Control
4
Power On
Power o
Play/Pause
Volume-
Volume+
Next Track
Answer/Hang Up a Phone
Call
Reject a Phone Call
Switch Between Two
Active Calls
Manual Pairing
Activate the Voice
Assistant
ANC/Transparency mode
Auto：Open the charging case
Manually: Press and hold the multifunctional button for
1.5s
Auto：Place the earbuds back into the
charging case and close the case lid
Manually: Press and hold the multifunctional button for 10s
Double-tap on the multifunctional button
Single-tap on the le multifunctional button
Single-tap on the right multifunctional button
Press and hold the right multifunctional button for 1.5s
Double-tap on the multifunctional button
Press and hold the multifunctional button for 1.5s
Press and hold the multifunctional button for 1.5s
Take out the two earphones from the charging case while
they are connected to your device,and then press and
hold the multifunctional buttons for 6s.
Press the multifunctional button for three times
Press and hold the le multifunctional button for 1.5s
3
Product Diagram
5
Q&A
1) The battery life of the charging case:
2) Charging status of the charging case:
100%—50%
49%-10%
<10%
Green
Yellow
Red
English English
Q1: What does the indicator of the charging
case display?
1. Connect the charging case to a Type-C
charger. (The current does not exceed 1A).
2. If the earphones stay idle for an extended
period of time, charge them at least every
three months to prevent the battery from
being damaged.
Q2: How to charge the charging case?
First Time of Using
1. Open the cover of the charging case, take out the two earphones, remove
the insulation lm on them separately, and then put both earphones back
into the charging case. By this time, the le and right earphones will
automatically enter the TWS mutual pairing state. Aer successful mutual
pairing, the blue light in the right earphone will ash slowly and the blue light
in the le earphone will always be on, and the two earphones will enter the
pairing mode.
2. Then go to Bluetooth settings of your device, and choose SOUNDPEATS T3.
SOUNDPEATS T3
Connected
T3
T3
User Guide | Gebrauchsanweisung | Manual de instrucciones |
Mode d'emploi | Istruzioni per l'uso
| 取扱説明ガイド|说明使用指南
1.Clear the pairing data from your device.
2. Take out the two earphones from the charging
case, press and hold the multifunctional buttons
for 10s until the blue indicator lights in both
earphones ash for three times and then go out.
At this time, the earphones are o, and then
press and hold the multifunctional buttons of
both earphones again for 10S until the blue
indicator lights ash twice, and the reset is
completed.
3. Place the earbuds back into the charging case
and close the case lid, waiting for seconds, and
then open it again. The earphones are
activated successfully.
1. Identify the le earphone and the right earphone.
2. Adjust the earphones to t your ears.
6
1. Check whether the charging case has battery power. If it has run out of
battery, closing it will not disconnect the earphones from the device.
2. Make sure the headphones are properly placed in the charging case and the
charging metal sheet and PIN are both clean. And wiping clean the contact
points on the earphones and the charging case should x this issue.
Q3: Why are the earphones still connected to the phone when they are put
back to the charging case and the case lid is closed?
English
7
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifcations not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
FCC Statement
FCC ID: 2AFTU-DD026 Made in China
XXX-XXXXXX
Room 1308-1309, Building B, Huihai Square, Chuangye Road,
Longhua District, Shenzhen, China. 518109
[e-mail]
www.soundpeatsaudio.com
MANUFACTURER
Shenzhen SoundSOUL Information Technology Company Limited
Company：Qing UG(haftungsbeschränkt)
Address：Undinestr. 7, 12203 Berlin Germany
EC REP
<10%
11%-49%
50%-99%
100%
Stay on Red
Stay on Yellow
Stay on Green
O
1.5s 3x 2x 1x 1.5s3x2x1x