Connection Diagram

1/R/
ww
LED
RF Receiver
Learning Key
Repeater Signal
Recei ve r Repea te r
2/G/
cw
3/B/
ww
4/W/
cw
LED Controllers
09.009PD.04013
Learning Key:
Pairing with RF remote
Function introduction
Important: Read All Instructions Prior to Installation
12-36V DC power input
Common Anode output(+)
Product Data
Input
Voltage
Remarks
Output
Current
12-36VDC
Constant voltage
4x(60-180)W
4x5A
Output
Power
12-36VDC
Constant current
4x(4.2-12.6)W
4x350mA
12-36VDC
Constant current
4x(8.4-25.2)W4x700mA
No.
1
2
3
Waterproof grade: IP20
Radio Frequency : 869.5/916.5/434mhz
Size(LxWxH)
166x53.4x23mm
166x53.4x23mm
166x53.4x23mm
CH 1:R-/WW- output
CH 2:G-/CW- output
CH 3:B-/WW- output
CH 4:W-/CW- output
Receiver / Repeater
Repeater signal input/output
Receiver/Repeater setting jumper:
One receiver can connect multiple repeaters to realize perfect sync the sync distance can be over 100m no volt
drop.
Pair/delete the pairing with RF remote
1.Do wiring according to connection diagram.
2.Pair RF Receiver with RF remote: please refer to the instruction of the remote that you would like to pair with.
3.Delete the pairing:
(1)Wire up the RF receiver correctly, power on.
(2)Press and hold down the “ Learning Key” button on receiver for over 3 seconds until the connected light
flashes, which means well deleted.
Wiring Diagram
If Con ne ct w ith RGBW LED St ri p
V+ V+
R- R-
G- G-
B- B-
W- W-
V+ V+
1- V-
2- V-
3- V-
4- V-
If Con ne ct w ith Single Co lo r LED Strip
V+ V+
WW WW
CW CW
WW WW
CW CW
If Con ne ct w ith Dual Colo r LE D Strip
With single color lighting
With dual color lighting
If Con ne ct w ith RGBW LED St ri p
V+ V+
R- R-
G- G-
B- B-
W- W-
If Con ne ct w ith RGBW LED St ri p
V+ V+
R- R-
G- G-
B- B-
W- W-
Repeater
Repeater
Receiver
1/R /
ww
LED
RF Receiver
Lea rning K ey
Rep eater S ignal
Rece iver Repe ater
2/G /
cw
3/B /
ww
4/W /
cw
1/R /
ww
LED
RF Receiver
Lea rning K ey
Rep eater S ignal
Rece iver Repe ater
2/G /
cw
3/B /
ww
4/W /
cw
1/R /
ww
LED
RF Receiver
Lea rning K ey
Rep eater S ignal
Rece iver Repe ater
2/G /
cw
3/B /
ww
4/W /
cw
1/R /
ww
LED
RF Receiver
Lea rning K ey
Rep eater S ignal
Rece iver Repe ater
2/G /
cw
3/B /
ww
4/W /
cw
1/R /
ww
LED
RF Receiver
Lea rning K ey
Rep eater S ignal
Rece iver Repe ater
2/G /
cw
3/B /
ww
4/W /
cw
V+
V-
OUTPUT
12V/24V/36V
CV PSU
V+
V-
OUTPUT
12V/24V/36V
CV PSU
V+
V-
OUTPUT
12V/24V/36V
CV PSU
With RGBW lighting(Receiver & repeater mode)
166 mm
53.4 mm
23 mm
Product Dimension
SR-1009PD
FCC Warning Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.Caution: Any changes or modifications to this device not explicitly approved by manufacturer
could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.