Knowledge Center 802.11 Mode: Select a correct network mode according to your wireless clients. 11b mode: This network mode delivers wireless speed up to 11Mbps and is only compatible with 11b wireless clients. 11g mode: This network mode delivers wireless speed up to 54Mbps and is only compatible with 11g wireless clients. 11b/g mixed mode: This network mode delivers wireless speed up to 54Mbps and is compatible with 11b/g wireless clients.
Configuration Procedures: ① Configure Security Mode, Cipher Type and Security Key. ② Click Save to save your settings. Knowledge Center WEP: W EP is intended to provide data confidentiality comparable to that of a traditional wired network. Open: If selected, wireless speed can reach up to 54Mbps. Shared: If selected, wireless speed can reach up to 54Mbps. Default Key: Select a key to be effective for the current W EP encryption.
TKIP: If selected, wireless speed can reach up to 54Mbps. TKIP&AES: If selected, both AES and TKIP secured wireless clients can join your wireless network. Key Renewal Interval: Enter a valid time period for the key to be changed. WPS Wi-Fi Protected Setup makes it easy for home users who know little of wireless security to establish a home network, as well as to add new devices to an existing network without entering long passphrases or configuring complicated settings.
Device PIN: Displays the device’s PIN code. Start PIN: If you enter the client’s PIN code on the router, clicking this button starts the PIN connection. Operation Instructions: PBC: If you press the hardware W PS button on the device for 1 second, the WPS LED will blink for about 2 minutes, indicating that the PBC encryption method is successfully enabled. During this time, an authentication routine can be performed between your device and a W PS/PBC capable wireless client.
B. If you want to allow ONLY the specified wireless clients to join your wireless network, select Allow. C. If you want to disallow ONLY the specified wireless clients to join your wireless network, select Deny. Wireless Access Control Application Example: To only allow your own notebook at the MAC address of C8:3A:35:CC:34:25 to join your wireless network : ① Select Allow. ② Enter C8:3A:35:CC:34:25. ③ Click Add to add the MAC address to the MAC address list. ④ Click Save to save your settings.
devices (if any) connected to the device. Tip ① The Bandwidth here refers to the channel bandwidth instead of wireless connection rate. ② You can know whether there are unauthorized accesses to your wireless network by viewing this connection status list .
4 Advanced Applications This section includes the following: To remotely access the device via a domain name or access a server on a LAN PC, see 4.1 DDNS Settings. To let an Internet user access your LAN PC without any restriction, see 4.2 DMZ Host. To automatically map the ports between WAN and LAN, see 4.3 UPNP. To enable the remote W eb management feature, see 4.4 Remote Web Management. To regulate bandwidth, see 4.5 Bandwidth Control (Available only in 4G600).
Tip To use the DDNS feature, you need to have an account with one of the DDNS Service Providers in the drop-down list first. DDNS Application Example: If your ISP gives you a dynamic (changing) public IP address, you want to access your router remotely ( see 4.4 Remote Web Management) but you cannot predict what your router's WAN IP address will be, and the address can change frequently. In this case, you can use a commercial Dynamic DNS service.
DDNS service provider. Here in this example, enter tenda. ④ Password: Enter the DDNS Password you have registered with your DDNS service provider. Here in this exampl e, enter 123456. ⑤ Domain Name: Enter the DDNS domain name you have registered with your DDNS service provider. Here in this example, enter tenda.dyndns.org . ⑥ Click Save to save your settings. ⑦ Click Remote Web Management , enable the Remote Web Management feature, enter 8090 in the Port field, 218.88.93.
(218.88.93.33) followed by a colon (:) and the remote management port number. Here in this example, enter http://tenda.dyndns.org:8090 . 4.2 DMZ Host The DMZ (De-Militarized Zone) function disables the firewall on the router for one device for a special purpose service such as Internet gaming or video conferencing applications that are not compatible with NAT (Network Address Translation). Click Advanced -> DMZ Host to enter the screen below. Note ① DMZ host poses a security risk.
will be disabled. Be sure to statically set the IP address of the device that serves as a DMZ host for this function to be consistent. ② Enable: Check to enable the DMZ host functionality. ③ Click Save to save your settings. Tip Security softwares such as anti-virus softwares and OS built-in firewall, etc. may affect the DMZ host feature. Disable them if the DMZ host fails. 4.
4.4 Remote Web Management The Remote Web Management allows the device to be configured and managed remotely from the Internet via a Web browser. Click Advanced -> Remote Web Management to enter the configuration screen. Tip ① For better security, configure a port number (between 1025 and 65535) as the remote Web management interface, do not use the number of any common service port (1~1024). ② Make sure your WAN IP address (Internet IP address) is a public IP address.
PC (218.88.93.33) at your office via the port number of 8090, follow the steps below: ① Enable: Check to enable the remote Web management feature. ② Port: Enter 8090. ③ IP Address: Specify the IP address for remote managemen t. Here in this example, enter 218.88.93.33 . ④ Click Save to save your settings. Type "http://102.33.66.88:8090" into your browser ’s address or location field and you can remotely access the router from your home.
bandwidth for each such PC, so that no one will be over stuffed or starved to death. Note that this feature is unavailable in 3G/4G Router Mode. Bandwidth Control Application Example: You share a 4M-broadband service with your neighbor (at the IP address of 192.168.0.125). He always downloads a large volume of data from the Internet, which sharply frustrates your Internet surfing experience; you can use this feature to set limits for the volume of Inte rnet traffic he can get.
Tip ① 1M=128KByte/s. ② The volume of uplink traffic/downlink traffic should not be larger than that allowed on your device's WAN (Internet) port. Consult your ISP, if you are not sure of the total volume of Internet traffic that you can have. ③ The bandwidth for ADSL/DSL li ne usually refers to the download bandwidth. 4.6 Client Filter (Available only in 4G600) This section allows you to set the times specific clients can or cannot access the Internet via the devices’ IP addresses and service port.
Knowledge Center Default: The default policy for the client filter. For the packets that do not match the set rule, the default rule is applied. Filter Mode: Specify a filter mode for the rule. Deny: Disallow the packets that match the set rule to pass the router. For other packets that do not match the set rule, the default policy is applied. Allow: Allow the packets that match the set rule to pass the router. For other packets that do not match the set rule, the defau lt policy is applied.
⑤ WAN Port Range: Enter a service port number. Here in this example, enter 80 in both boxes. HTTP port 80 is the standard protocol for Web servers. ⑥ Type: Select a protocol for the traffic. If you are unsure, select Both. ⑦ Time: Specify a time period for the current rule to take effect. Here in this example, select 8:00~18:00. Day: Select a day, or several days of the week for the current rule to take effect. Here in this example, select Mon, Tue, Wed, Thur and Fri. ⑧ Click Save to save your settings.
Tip ① The valid service port number range is 1 ~ 65535. ② If you have not set up the system time for this device, click Tools -> Time & Date to configure correct time and date settings for the rule(s) to be effective.
5 Tools To configure system time, see 5.1 Time & Date. To upgrade firmware, see 5.2 Firmware Upgrade. To backup or restore configurations, see 5.3 Backup & Restore. To restore factory default settings, see 5.4 Restore to Factory Default. To change login password, see 5.5 Change Password. To view logs, see 5.6 Logs. To restart device, see 5.7 Reboot. 5.1 Time & Date Click Tools -> Time & Date to enter the configuration screen.
Note In the Universal Repeater Mode, the Internet Time Server - Enable feature is not available, so you can only set the time and date manually. B. To set time and date manually/synchronize with your PC: ① Internet Time Server: Uncheck to disable the feature. ② Specify the time and date manually or automatically copy your PC's time to the device. ③ Click Save to save your settings.
④ Go to the Status screen to make sure the system time is correctly updated. 5.2 Firmware Upgrade Click Tools -> Firmware Upgrade to enter the configuration screen. Firmware upgrade is released periodically to improve the functionality of your device and also to add new features. If you run into a problem with a specific feature of th e device, log on to our Website (http://www.tendacn.com) to download the latest firmware to update your device.
① Click Browse. ② Select the firmware file you want to use and click Open. ③ Click Upgrade. ④ Click OK on the appearing screen and wait for it to complete. When upgrade is complete d, check the Current System Version field. It should display the firmware you load. 5.
② Click OK on the appearing window. ③ Click Save on the File Download window. ④ Select a local hard drive to save the file and click Save.
To restore configurations: ① Click Browse. ② Select the configuration file that is saved previously to your local hard drive and click Open.
③ Click the Restore button to reset your device to previous settings. 5.4 Restore to Factory Default Click Tools -> Restore to Factory Default to enter the configuration screen. Here you can reset the device to factory default settings. Note ① If you enable this option, the device will be restored to factory default values. You will have to reconfigure Internet connection settings and wireless settings.
you to reset the device. The factory default settings are listed below: IP Address: 192.168.0.1 Subnet Mask: Enter 255.255.255.0. Password: admin 5.5 Change Password Click Tools -> Change Password to enter the configuration screen. It is strongly recommended that you chang e the factory default login password. Otherwise, anyone in your network can access this utility to change your settings. Tip ① The default login password is "admin".
Configuration Procedures: ① Old Password: Enter the current login password. ② New Password: Input a new password. ③ Confirm New Password: Re-enter the new password for confirmation. ④ Click Save to save your settings. 5.6 Logs Click Tools -> Logs to enter the configuration screen. Here you can view the history of the device’s actions upon system startup.
5.7 Reboot When a certain feature does not take effect or the device is malfunctioning, try rebooting the device.
IV Appendix 1 Configure Your PC Windows 7 Step 1: Click the icon on the right bottom corner of your desktop. Step 2: Click Open Network and Sharing Center. Tip If you cannot find the icon on the right bottom corner of your desktop, follow steps below: Click Start -> Control Panel -> Network and Internet -> Network and Sharing Center.
Step 3: Click Local Area Connection -> Properties. Step 4: Find and double click Internet Protocol Version 4(TCP/IPv4).
Step 5: Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK. Step 6: Click OK on the Local Area Connection Properties window (see Step 4 for the screenshot). Windows XP Step 1: Right click My Network Places on your desktop and select Properties.
Step 2: Right click Local Area Connection and select Properties. Step 3: Scroll down to find and double click Internet Protocol (TCP/IP).
Step 4: Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK. Step 5: Click OK on the Local Area Connection Properties window (see Step 3 for the screenshot).
2 Join Your Wireless Network Tip ① To join your wireless network, the PC you use must have an installed wireless network adapter. If not, install one. ② The device’s SSID is "Tenda_XXXXXX" by default (where "XXXXXX" is the last six characters of its MAC address). You can find the MAC address and/or SSID on the label attached to the device’s bottom). Windows 7 Step 1: Click or from the right bottom of your desktop.
Windows XP Step 1: Right click My Network Places and select Properties. Step 2: Right click Wireless Network Connection and select View Available Wireless Networks.
Step 3: Double click the name of the wireless network (SSID) you wish to join and then follow onscreen instructions. When Connected appears next to the selected wireless network (SSID), you have successfully connected to it.
77 IV Appendix | Tenda
3 FAQs This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you are running into problems. If your problem is not covered here, please feel free to go to www.tendacn.com to find a solution or email your problems to: support@tenda.com.cn or support02@tenda.com.cn. We will be more than happy to help you out as soon as possible. 1. Q: I cannot access the device's management interface.
device. What should I do? Make sure there are no other DHCP servers on your LAN or other DHCP servers are disabled. Make sure the device's LAN IP is not used by other devices on your LAN. The device's default LAN IP address is 192.168.0.1. Make sure the statically assigned IP addresses to the PC(s) on LAN are not used by others device(s). 4. Q: I cannot access email and the Internet/Some Websites do not open.
4 Remove Wireless Network from Your PC When you change your wireless network (For example, change your device's SSID or security key), the old wireless settings on your PC will not be updated accordingly, you must manually remove them from your PC; otherwise, you may not be able to wirelessly connect to the device. This section explains how to remove a wireless network from your PC. Windows 7 ① Right-click the Network icon and select Properties. ② Select Manage Wireless Networks.
Windows XP ① Right-click My Network Places and select Properties. ② Right click Wireless Network Connection and then select Properties.
③ Click Wireless Networks, select the wireless network name under Preferred networks and then click the Remove button.
5 Safety and Emission Statement CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device complies with EU 1999/5/EC. NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ-45 cable.
- Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
