Wireless N450 Home Router 1
Wireless N450 Home Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without prior expressed written permission from Shenzhen Tenda Technology Co.
Wireless N450 Home Router Contents Copyright Statement ............................................................................................................................................................... 2 Contents ................................................................................................................................................................................. 3 Chapter 1 Product Overview...............................................................................
Wireless N450 Home Router 5.1 MAC Filter .......................................................................................................................................................................... 49 5.2 Client Filter......................................................................................................................................................................... 51 5.3 URL Filter ...........................................................................................
Wireless N450 Home Router Chapter 1 Product Overview 1 Package Contents Please verify that the package contains the following items: z Wireless Router z Power Adapter z Installation Guide z Ethernet Cable z Resource CD If any of the above items are incorrect, missing, or damaged, please contact your Tenda reseller for immediate replacement.
Wireless N450 Home Router LAN 1/ IPTV WiFi WPS SYS POWER Solid Blinking Off Solid Blinking Off Blinking Off Blinking Solid/Off Solid Off IPTV port is correctly connected IPTV port is transmitting data IPTV port is incorrectly connected WiFi is enabled Transmitting data WiFi is disabled Device is performing WPS authentication on a client device WPS is disabled or WPS authentication finished Indicates the system is functioning correctly Indicates the system is functioning incorrectly Indicates a proper co
Wireless N450 Home Router Label You can acquire the following information from Label: z Model: Displays the product model. z IP Address: The default IP is 192.168.0.1. z Password: The default password is admin. z MAC: Displays the device's default MAC address. z Wireless Network Name(SSID): Displays the device's default SSID name.
Wireless N450 Home Router Chapter 2 Installation and Quick Setup Guide 1 Preparation Before connecting Ethernet cables, please verify the following items: Item Description Wireless Router Used with the provided power supply PC Installed with IE8 or other better web browsers.
Wireless N450 Home Router 2. Connect one of the LAN ports on the router to the RJ45 (NIC) port on your PC using an Ethernet cable. 3. Connect the Ethernet cable from the incoming Internet side to the WAN port on the router. 3 Internet Connection Setup Configure PC Configure your PC obtain IP address automatically. If you are not clear about this, please refer to Appendix 1 Configure PC. Configure Router Login to Web Utility 1. Launch a web browser, such as IE Web browser; 2.
Wireless N450 Home Router 3. Enter a password in the corresponding field as shown in the window below (the default password is set to “admin”). Note For security purpose, please change the default password after you have logged in to the web utility.
Wireless N450 Home Router Internet Connection Setup Common Internet connection types are available on the home page: PPPoE and Dynamic IP. PPPoE Select PPPoE (Point to Point Protocol over Ethernet) if you used to connect to the Internet using a broadband connection that requires a username and a password. Enter the user name and password provided by your ISP; configure a security key to secure your wireless network and then click OK.
Wireless N450 Home Router Note 1. DHCP is the default Internet connection type; 2. If you are not sure about your PPPoE username and password, contact your Internet service provider (ISP) for help. For other Internet connection types, please go to section 2.2: WAN. 4 Verify Internet Connection Settings System automatically skips to the status page when you finish all needed settings on the home page. Here you can see the system status and WAN connection status of the device. 1.
Wireless N450 Home Router 3. If Connecting is displayed and no WAN IP address is seen, try refreshing the page five times. And if it still displays Connecting try steps below: 1). Contact your ISP for assistance. 2). Read the connection diagnostic info on WAN status. Note The following diagnostic info will be displayed on particular occasions for your reference: 1). You have connected to Internet successfully. 2). You might have entered a wrong user name and/or a wrong password.
Wireless N450 Home Router 5 Connect to Device Wirelessly Having finished above settings, you can search the device's wireless network (SSID) from your wireless devices (notebook, iPad, iPhone, etc) and enter a security key to connect to it wirelessly. Desktop computers should be equipped with wireless network cards. WIN7 OS 1. Click on the icon at the bottom of the right corner on your desktop; 2.
Wireless N450 Home Router 3. When the following dialog box appears, it indicates connecting to the network; 4. Enter your security key and click OK; 5. When displaying Connected, you have connected to network successfully. Tips ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ If you cannot find the icon at the bottom of the right corner on your desktop, please refer to Appendix 2 Join a Wireless Connection>Win7 OS.
Wireless N450 Home Router 2. Click Local Area Connection and select View Available Wireless Networks; 3. Select the SSID you wish to connect, such as Tenda_home, click Connect, enter the security key and then click OK; 4. You can access Internet via the device when Connected appears next to the wireless network name you selected.
Wireless N450 Home Router Chapter 3 Configurations This chapter describes the Web based configurations for easier management of your router. During the configuration operation, if you are not clear about a certain feature, simply read the related helpful info below. 1 Status 1.1 System Status Here you can see at a glance of the operating status of the device. 1.
Wireless N450 Home Router z z Secondary DNS Server: Displays the secondary WAN DNS address (if any). Up Time: Displays the time duration indicating how long the router has been connected to the ISP. 1.3 LAN Status This section allows you to view the router’s MAC, IP, and subnet mask information. z MAC Address: Displays the router’s LAN MAC address. z z IP Address：Displays the current LAN IP address. Subnet Mask: Displays the current LAN subnet mask. 1.
Wireless N450 Home Router 1.5 Connection Status This section displays the info of currently connected clients (if any) including IP and MAC addresses, etc. 2 Network Network menu includes the following nine submenus. Clicking any of them enters the corresponding interface for configuration. Details are explained below: 2.1 LAN This section allows you to configure your router's LAN IP settings.
Wireless N450 Home Router z z IP Address: The router’s LAN IP. The default is 192.168.0.1 and you can change it according to your needs. Subnet Mask: Router’s LAN subnet mask. The default is 255.255.255.0. Note If you change the LAN IP address, you must use the new one to log on to the web utility. 2.2 WAN There are three types of Internet connection: Dynamic IP (DHCP), Static IP, and PPPoE(including dual access).
Wireless N450 Home Router z z z z z z Connection Type: Displays a list of available Internet connection types. IP Address: Enter the IP address provided by your ISP. Consult your local ISP if you are not clear. Subnet mask: Enter the subnet mask provided by your ISP. Consult your ISP if you are not clear. Gateway: Enter the gateway address provided by your ISP. Consult your local ISP if you are not clear. Primary/Secondary DNS Server: Enter the Primary and Secondary DNS Server Addresses.
Wireless N450 Home Router degrade your network performance or even lead to network malfunction. 2. If you want to active new settings you’ve changed, you must reboot the device. ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ 2.3 Port Mode Mode includes auto,10M Half‐Duplex,10M Full‐Duplex,100M Half‐Duplex,100M Full‐Duplex,1000M Full‐Duplex. Default is auto, and do not change it unless necessary. 2.
Wireless N450 Home Router networks. If you enable the built‐in DHCP server on this device, it will automatically configure the TCP/IP protocol settings for all PC’s in the LAN, including IP address, subnet mask, gateway, and DNS. z z z z DHCP Server: Select whether to enable or disable the router’s DHCP server feature. Start IP Address: Enter the starting IP address for the DHCP server’s IP assignment. End IP Address: Enter the ending IP address for the DHCP server’s IP assignment.
Wireless N450 Home Router z Lease Time: Remaining time for a corresponding IP address lease. 2.7 Static Assignment If you would like some devices on your network to always have fixed IP addresses, you can use this feature and manually add a static DHCP assignment entry for each device. For example: To have a PC at the MAC address of 00:15:58:c0:d4:3f always receive the same IP address of 192.168.0.
Wireless N450 Home Router z z z z DHCP Server: Select whether to enable or disable the router’s DHCP server feature. Start IP Address: Enter the starting IP address for the DHCP server’s IP assignment. End IP Address: Enter the ending IP address for the DHCP server’s IP assignment. Lease Time: The length of time for the IP address lease.
Wireless N450 Home Router The Wireless tab includes 8 submenus: Basic, Guest Network, Security, Advanced, Wireless Access Control, Wireless Extender, WPS, and Connection Status. Clicking any of them enters the corresponding interface for configuration. Details are explained below: 3.1 Basic This section allows you to manage your wireless network. You can select your country, configure the wireless network name (SSID), network mode, and channel settings, etc. z z z z z z 2.
Wireless N450 Home Router z you select an unused channel from the drop down list, or “Auto” to let the router detect and select the best possible channel for your wireless network to operate on. Channel Bandwidth: Select a proper channel bandwidth to enhance wireless performance. When there only 11n or a mix of 11b/g/n wireless clients, please select the 802.
Wireless N450 Home Router Three security modes are available: None, WEP, and WPA‐PSK/WPA2‐PSK. WEP WEP is intended to provide data confidentiality comparable to that of a traditional wired network. Two methods of authentication can be used with WEP: Open System authentication and Shared Key authentication. z Authentication Type: Select Open or Shared from the drop‐down list. z WEP Key Format: Select Hex or ASCII from the drop‐down list. z Key Select: Select a key from the preset keys 1‐4 for current use.
Wireless N450 Home Router z Cipher Type: Select AES (advanced encryption standard) or TKIP (temporary key integrity protocol) &AES. z Security Key: Enter a security key, which must be between 8‐63 ASCII characters long. z Key Renewal Interval: Enter a valid time period for the key to be changed. WPA2‐PSK WPA2 is based on 802.11i and uses Advanced Encryption Standard (AES) instead of TKIP. It is more secured than WPA and WEP.
Wireless N450 Home Router z z z z z z z AP Isolation: Isolates clients connecting to the master SSID. Beacon Interval: A time interval between any two consecutive Beacon packets sent by an Access Point to synchronize a wireless network. DO NOT change the default value of 100 unless necessary. Fragment Threshold: Specify a Fragment Threshold value. Any wireless packet exceeding the preset value will be divided into several fragments before transmission.
Wireless N450 Home Router z Filter Mode: Deny Access to Wireless Network: Blocks only devices at specified MAC addresses from connecting to your wireless network. Allow Access to Wireless Network: Allow only devices at specified MAC addresses to connect to your wireless network. Click Add and the screen below will open: z z z MAC Address: Enter the MAC address of a wireless client. Description: Briefly describe the new entry. Status: Select Enable/Disable to enable/disable a corresponding entry. 3.
Wireless N450 Home Router WDS WDS (Wireless Distribution System), this feature can be used to extend your existing 2.4Ghz network coverage. The details below outline how to configure this feature in the 2.4GHz band. For example: As seen in the figure above, PC1 and PC2 access Internet via a wireless connection to Router 1. While PC3 and PC4 are too far to directly connect to Router 1 for Internet access. Now you can use the WDS bridge feature to let PC3 and PC4 access Internet. Before you get started: 1.
Wireless N450 Home Router 2. Click Wireless>Basic to check the basic settings of Router 1. 3. Click Wireless>Security to check wireless security settings of Router 1.
Wireless N450 Home Router 4. Verify that DHCP server is enabled on Router 1: Click Network>DHCP Server. 5. Set the LAN IP address of Router 2 to a different address yet on the same net segment as Router 1. As shown below: Router 1: LAN IP: 192.168.0.1; Subnet Mask: 255.255.255.0; Router 2: LAN IP：192.168.0.10; Subnet Mask: 255.255.255.0; Then do as follows: 1. Configure Router 2: 1) Wireless Working Mode: Select WDS Bridge Mode. 2) Click Open Scan to search for Router 1.
Wireless N450 Home Router 3) Select the wireless network to connect and click OK. 4) Verify that the SSID, channel, and AP MAC address on the page match those of the added wireless network. If not, manually correct them. 5) Close Scan and click Save to save your settings. 6) Go to Wireless Security page and set the wireless security settings exactly as they are on the link partner (Router 1). 7) Go to DHCP Server to disable the DHCP on Router 2.
Wireless N450 Home Router 36
Wireless N450 Home Router After the above configurations, you can verify the connection by pinging Router 2’s IP. Steps are as follows (Take Windows XP OS for example): 1) Click Start >Run; 2) Then the below screen appears and enter cmd; 3) Input ping 192.168.0.10 in the screen and press Enter. If the folllowing screen appears, it indicates you have finished the configuration successfully.
Wireless N450 Home Router Note 1. WDS feature can only be implemented between 2 WDS‐capable wireless devices. Additionally, the SSID, channel, security settings, and security key must be exactly the same on both such devices. 2. Note that the two devices involved must have different IP addresses on the same IP net segment. In addition, it is advisable to disable the DHCP server on either device. WISP Mode If your router acquires Internet access from a wireless Access Point, please select WISP mode.
Wireless N450 Home Router 7. Click Status>WAN Status and the connection status displays Connected. Note 1. When the settings finished, remember to enter Connection Setup to set up Internet connection. 2. Verify that the SSID, channel, and security mode on the page match those of the added wireless network. If not, manually correct them. 3. For the normal wireless connection between two routers, do not change this router’s SSID settings, including SSID, channel, security mode and security key.
Wireless N450 Home Router 2. Click Open Scan, select the AP you wish to connect and click OK. 3. View and note down the wireless security settings: security mode, cipher type, security key, etc., which should be in accordance with the upper device. 4. Click Close Scan and OK. 5. Save the settings and the router will restart automatically. 3.
Wireless N450 Home Router ● Enable WPS: Select to enable/disable the WPS encryption. ● WPS Mode: Select PBC (Push‐Button Configuration) or PIN. ● Reset OOB: When selected, the WPS LED turns off and the WPS function will be disabled automatically. The WPS server on the router enters idle mode and will not respond to any client’s WPS connection request.
Wireless N450 Home Router 4 Advanced Applications The Advanced tab includes the following 8 submenus: Bandwidth Control, DDNS, Virtual Server, DMZ Host, UPnP, IPTV, Routing Table, and Static Routing. Clicking any of them enters the corresponding interface for configuration. Details are explained below: 4.1 Bandwidth Control To better manage bandwidth allocation and optimize network performance, use the Bandwidth Control feature. Click Add Bandwidth Control Rule and the screen below will open.
Wireless N450 Home Router ● Enable: Check/uncheck to enable/disable current entry. When disabled, corresponding entry will not take effect. ● IP Range: Enter a single IP or an IP range. ● Uplink Bandwidth: Max uplink traffic. ● Downlink Bandwidth : Max downlink traffic. ● Description: Briefly describe the current entry. 4.2 DDNS Dynamic DNS or DDNS is a term used for the updating in real time of Internet Domain Name System (DNS) name servers.
Wireless N450 Home Router ● Ext Port ‐ Int Port: External Port ‐ Internal Port, enter the WAN/LAN service ports. ● Internal IP: The IP address of a computer used as a server in LAN. ● Protocol: Includes TCP, UDP, and Both. Select “Both” if you are not sure about which protocol to use ● Enable: The corresponding entry takes effect only if you checked this option. ● Delete: Remove a corresponding entry ● Well‐known Service Port: The well‐known Service Port lists widely used protocol ports.
Wireless N450 Home Router 3. Click Save to save your settings. Now, your friends only need to enter ftp://xxx.xxx.xxx.xxx:21 in their browsers to access your FTP server. xxx.xxx.xxx.xxx, Assuming the router's WAN IP address is 172.16.102.89, then your friends need to enter "ftp://172.16.102.89: 21" in their browsers.
Wireless N450 Home Router ● Enable: Check/uncheck to enable/disable the DMZ host feature. ● DMZ Host IP: Enter the IP address of a computer on your LAN which you want to set as a DMZ host. The DMZ host should be connected to a LAN port on the router. Note 1. Once a PC is set to a DMZ host, it will be completely exposed to Internet, and thus may be vulnerable to attacks as related firewall settings become inoperative. 2. Users on the WAN can access the DMZ host through a corresponding WAN IP address.
Wireless N450 Home Router ● Enable IPTV: Check/uncheck to enable/disable the IPTV feature. ● Enable IPTV STB Port: Check/uncheck to enable/disable the IPTV‐specific port. See below for the network topology: Note 1. If you enabled both options mentioned above, then note below: (a). Set IPTV set‐top box's connection type to DHCP/dynamic IP or static IP (IMPORTANT: Note that the set‐top box's IP address should be on the same IP net segment as the router’s LAN IP.
Wireless N450 Home Router 3. The IPTV feature is currently not supported on WLAN. 4.7 Routing Table This feature displays the routing table content. 4.8 Static Routing Use this section to customize static routes of data through your network.
Wireless N450 Home Router ● Destination Network: The IP address of a destination network. ● Subnet Mask: The Subnet Mask that corresponds to the specified destination IP address. ● Gateway: The IP address for next hop. 5 Security The Security tab includes 6 submenus: MAC Filter, Client Filter, URL Filter, Remote Web Management, DDoS Defence and SPI Firewall. Clicking any of them enters the corresponding interface for configuration. Details are explained below: 5.
Wireless N450 Home Router ● Filter Mode: ● Disable: Disable the MAC Filter feature. ● Deny Access to Internet: Disallow only specified devices to access Internet, other devices are not restricted. ● Allow Access to Internet: Allow only specified devices to access Internet, other devices are denied. ● Select: Select an ID for the current entry. ● Description: Briefly describe current entry. ● MAC: Specify the MAC address of the computer that you want to restrict.
Wireless N450 Home Router 5.2 Client Filter To better manage devices in the LAN, you can allow or disallow the devices to access certain ports on the Internet using the Client Filter function. ● Filter Mode: Select Deny or Allow. ● Select: Select an ID for the current entry. ● Description: Briefly describe the current entry. ● Start IP: Enter a starting IP address. ● End IP: Enter an ending IP address. ● Port: Enter TCP/UDP protocol port number, it can be a single port or a range of ports.
Wireless N450 Home Router 5.3 URL Filter To better control LAN devices, you can use the URL filter function to allow or disallow PC’s to access certain websites within a specified time range. ● Filter Mode: Select Deny or Allow. ● Select: Select an ID for current entry. ● Enable: Check to enable or uncheck to disable a corresponding filter rule (allow/disallow matched addresses to pass through router). ● Description: Briefly describe the current entry. ● Start IP: Enter a starting IP address.
Wireless N450 Home Router If you want to disallow all computers on your LAN to access Google.com from 8:00 to 18:00 on working days: Monday‐ Friday, then use the following example: Note Each entry can include up to 16 domain names, each of which must be separated with the quotation symbols " ". 5.4 Remote Web Management The Remote management allows the router to be configured from the Internet via a web browser. ● Enable: Select to enable the Remote Web‐based Management feature.
Wireless N450 Home Router Note 1. The default port is 8080. Do not change it. 2. To access the router via port 8080, enter "http://x.x.x.x:8080" where "x.x.x.x" represents the Internet IP address of the router and 8080 is the port used for the Web‐Management interface. Assuming the router's Internet IP address is 220.135.211.56, then simply replace the "x.x.x.x" with "220.135.211.56" (namely, http://220.135.211.56:8080). Leaving the IP address field at "0.0.0.
Wireless N450 Home Router Tips ‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐ Once SPI enabled, DMZ and remote web management will be invalid.
Wireless N450 Home Router 6.2 Traffic Statistics Traffic Statistics displays current traffic of clients on your LAN. ● Enable Traffic Statistics: Determine whether to enable the Traffic Statistics feature on internal users. ● Refresh: Click it to update statistic data. ● Clear: Click it to remove statistic data. Note Enabling the Traffic Statistics feature may degrade the router’s performance. Do not enable it unless necessary. 6.
Wireless N450 Home Router management interface. Both login password and user name are preset to “admin” by default. To change either or both, do the following: 1. Enter your current user name and password in Old User Name and Old Password fields. 2. Enter a new user name and a new password in New User Name and New Password fields. 3. Click Save. Note For security purpose, it is highly recommended that you change the default login password and user name as part of the initial configuration of your router.
Wireless N450 Home Router 6.7 Firmware Update Firmware upgrade is released periodically to improve the functionality of your router, and also to add any new features. If you run into a problem with a specific feature of the router you could log on to our website (www.tendacn.com) to download the latest firmware to update your device. To update firmware, do the following: 1. Click Browse to locate and select the firmware file and Upgrade to update your router. 2.
Wireless N450 Home Router 6.9 Reboot This section allows you to reboot the router.
Wireless N450 Home Router Appendix 1 Configure PC In this section we explain how to configure your PC’s TCP/IP settings. WIN7 OS 1. Click Start>Control Panel; 2. Enter Control Panel and click Network and Internet; 3.
Wireless N450 Home Router 4. Click Change adapter settings; 5.
Wireless N450 Home Router 6. Select Internet Protocol Version 4(TCP/IPv4) and click Properties; 7. Select Obtain an IP address automatically and click OK to save the configurations.
Wireless N450 Home Router Windows XP OS 1. Right click My Network Places and select Properties; 2. Right click Local and select Properties; 3.
Wireless N450 Home Router 4. Select Obtain an IP address automatically and click OK to save the settings.
Wireless N450 Home Router Appendix 2 Join a Wireless Connection Note For wireless connection, desktop computers need to be equipped with wireless network cards first. Win7 OS 1. Click Start>Control Panel; 2.
Wireless N450 Home Router 3. Click Network and Sharing Center; 4. Click Change adapter settings; 5.
Wireless N450 Home Router 6. Select the network you wish to connect, such as Tenda‐000090; According to different cipher types, here goes two situations: A.
Wireless N450 Home Router B. If you have configured security key, click Connect; When the following dialog box appears, it indicates connecting to the network; 7. When displaying Connected, you have connected to network successfully.
Wireless N450 Home Router Appendix 3 FAQs This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you are running into problems. If your problem is not covered here, please feel free to go to www.tendacn.com to find a solution or email your problems to: support@tenda.com.cn or support02@tenda.com.cn. We will be more than happy to help you out as soon as possible. 1.
Wireless N450 Home Router Step 6: Click Enable and save your settings. For your reference, we collected a list of some well‐known service ports as follows: Server Protocol Service Port Web Server TCP 80 FTP Server TCP 21 Telnet TCP 23 Net Meeting TCP 1503、1720 File Send:6891‐6900(TCP) MSN Messenger TCP/UDP Voice:1863, 6901(TCP) Voice:1863, 5190(UDP) PPTP VPN TCP 1723 Iphone5.
Wireless N450 Home Router Appendix 4 Glossary Channel A communication channel, also known as channel, refers either to a physical transmission medium such as a wire or to a logical connection over a multiplexed medium such as a radio channel. It is used to transfer an information signal, such as a digital bit stream, from one or more transmitters to one or more receivers. If there is only one AP in the range, select any channel you like. The default is Auto.
Wireless N450 Home Router DNS The Domain Name System (DNS) is a hierarchical distributed naming system for computers, services, or any resource connected to the Internet or a private network. It associates various information with domain names assigned to each of the participating entities. A Domain Name Service resolves queries for these names into IP addresses for the purpose of locating computer services and devices worldwide.
Wireless N450 Home Router Appendix 5 Remove Wireless Network from Your PC If you change wireless settings on your wireless device, you must remove them accordingly your PC; otherwise, you may not be able to wirelessly connect to the device. Below describes how to do remove a wireless network from your PC. Windows XP OS 1. Right click My Network Places and select Properties. 2. Click Wireless Network Connection and then select Properties. 3.
Wireless N450 Home Router Windows 7 OS 1. Click Network from your desktop and select Properties. 2. Select Manage Wireless Networks. 3. Click the wireless connection and select Remove network.
Wireless N450 Home Router Appendix 6 Safety CE Mark Warning This is a Class B product In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device complies with EU 1999/5/EC. NOTE:(1)The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
