Quick Installation Guide N300 Wi-Fi xPON ONT HG3 Package contents • xPON ONT x 1 • Power adapter x 1 • Ethernet cable x 1 • User manual x 1 For product or function details, please go to www.tendacn.com to download the user guide.
Get to know the ONT LED indicators PWR PON LOS LAN WLAN LED indicator Color PWR Green PON LOS LAN WLAN Status Solid on Off Green Red Green Green Description The ONT is powered on properly. The ONT is powered off or not powered on properly. Solid on The ONT is registered successfully. Blinking The registration is not completed (unregistered or registering). Off The received optical power is lower than the optical receiver sensitivity, or no fiber cord is connected.
Ports & Button WPS/RST PON LAN2 LAN1-GE PWR Port/Button Description WPS/RST WPS/Reset button. • WPS: Wi-Fi-enabled devices can connect to the Wi-Fi networks of the ONT without entering the password through WPS negotiation. Press the button for 1 to 3 seconds to start the WPS negotiation process of the ONT. The WLAN LED indicators blink quickly. Within 2 minutes, enable the WPS function on a WPS-supported device to establish a WPS connection.
1. Connect and register the ONT Caution, laser DO NOT look directly at the PON port when the device is powered on, as well as the terminal of the indoor fiber cord, to prevent any harm to your eyes. Connect the ONT as shown in the figure. The ONT automatically adapts to the fiber access type. Wait until the PON LED indicator lights solid on, then the ONT is registered successfully.
2. Configure the internet access Tips: Choose a desired mode to configure your internet access: • Router mode: Choose this mode if your internet access type is PPPoE or DHCP. • Bridge mode (default): Choose this mode if your internet access type is PPPoE.
PON WAN This page is used to configure the parameters for PONWAN nas0_0 Enable VLAN: VLAN ID: 0 802.
Step 2: Set up a WAN connection ➊ Choose WAN > PON WAN. ➋ Tick Enable VLAN. ➌ Enter the VLAN ID provided by your ISP. ➍ Set Channel Mode to IPoE. ➎ Set Connection Type to INTERNET. ➏ Click Apply Changes. PON WAN This page is used to configure the parameters for PONW nas0_0 Enable VLAN: VLAN ID: 0 802.
Bridge mode Tips: When the ONT is set to Bridge mode, please configure internet settings based on ISP requirements. Access internet over PPPoE ➊ Connect a LAN port of the ONT to the WAN port of a router using an Ethernet cable. ➋ Connect your computer to a LAN port of the router using an Ethernet cable. ➌ Set up a PPPoE connection on the router as required. After the settings, you can access the internet through the router.
FAQ Q1: I cannot log in to the web UI by visiting 192.168.1.1. What should I do? A1: Try the following solutions: • Ensure that the ONT is powered on properly (the PWR LED indicator is solid green). • If you use a wireless device, such as a smartphone, to configure the ONT: - Ensure that your smartphone has disabled mobile data and is connected to the Wi-Fi network of the ONT. - Clear the cache of the web browser or change a web browser and try again. - Use another smartphone and try again.
Q4: How to reset the ONT? A4: Method1: After the ONT completes startup, press the WPS/RST button for 8 seconds and release it. All LED indicators will light off in a few seconds. When the PWR LED indicator lights solid on again, the ONT is reset. Method2: Log in to the web UI of the ONT, choose Admin > Backup/Restore and click Reset on the page.
FCC Compliance Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
