Wireless N150/N301 Easy Setup Router
Wireless N150/N301 Easy Setup Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names mentioned herein are the trademarks or registered trademarks of their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without prior expressed written permission from Shenzhen Tenda Technology Co.
Wireless N150/N301 Easy Setup Router Contents COPYRIGHT STATEMENT ....................................................................................................... 1 CHAPTER 1 PRODUCT OVERVIEW ...................................................................................... 1 1 PACKAGE CONTENTS ................................................................................................................ 1 2 LEDS AND PORTS ........................................................................
Wireless N150/N301 Easy Setup Router 6.2 Restore to Factory Default Settings....................................................................................................58 6.3 Backup/Restore...................................................................................................................................58 6.4 Syslog .................................................................................................................................................60 6.
Wireless N150/N301 Easy Setup Router Chapter 1 Product Overview 1 Package Contents Unpack the box and verify that the package contains the following: ⑴Wireless Broadband Router ⑵Power Adapter ⑶Quick Install Guide If any of the above items is incorrect, missing, or damaged, please contact your Tenda reseller for immediate replacement. 2 LEDs and Ports This part describes this device’s hardware features.
Wireless N150/N301 Easy Setup Router ◈ Back Panel Back LED Overview: Port Function Description Usually for connecting DSL MODEM 、 CABLE WAN MODEM、ISP to the Internet. 1/2/3 WPS/ RST PWR Usually for connecting computers, switches .etc. When you press this button for 7 seconds, files set by the router will be deleted and restored to default factory; for 1 second, WPS will be enabled and the WPS LED will be blinking accordingly.
Wireless N150/N301 Easy Setup Router Chapter 2 Installation and Quick Setup Guide 1 Physical Installation 1.1 Preparation Before connecting network lines, please verify the following items: Item Description Wireless Router Used with the provided power supply PC Installed with IE8 or other better web browsers.
Wireless N150/N301 Easy Setup Router 1.2 Physical installation 1. Connect one end of the included power adapter to the device and plug the other end into a wall outlet nearby.(Using a power adapter with a different voltage rating than the one included with the device will cause damage to the device) 2. Connect one of the LAN ports on the Device to the NIC port on your PC using an Ethernet cable. 3. Connect the Ethernet cable from Internet side to the WAN port on the device.
Wireless N150/N301 Easy Setup Router 2 Internet Connection Setup 2.1 Log in to Web Manager 1. Launch a web browser, such as IE Web browser; 2. In the address bar, input 192.168.0.1 and press Enter; 3. Enter admin in the password field on the appearing login window and then click OK. 4. Now you may access the device’s home page for quickly setting up Internet connection and wireless security. 5.
Wireless N150/N301 Easy Setup Router 5. If you fail to log in to it, please refer to Appendix 3 FAQs. 6.
Wireless N150/N301 Easy Setup Router 2.2 Internet Connection Setup Common Internet connection types are available on the home page: PPPoE and DHCP. DHCP Select DHCP (Dynamic IP) if you can access Internet as soon as your computer directly connects to an Internet-enabled ADSL/Cable modem; configure a security key (8-63 characters) to secure your wireless network and then click OK.
Wireless N150/N301 Easy Setup Router Note: 1. DHCP is the default Internet connection type; 2. If you are not sure about your PPPoE username and password, contact your Internet service provider (ISP) for help. For other Internet connection types, please go to section 1.2: Internet Connection Setup. 8.
Wireless N150/N301 Easy Setup Router 3 Verify Internet Connection Settings System automatically skips to the status page when you finish all needed settings on the home page. Here you can see the system status and WAN connection status of the device. 1. If you find "Connected" and a WAN IP address displayed there (as shown below), you have got a wired internet access now. 2.
Wireless N150/N301 Easy Setup Router 1). Contact your ISP for assistance if you are using the DHCP connection type. 2). Read the connection diagnostic info on WAN status. Note: Below diagnostic info will be displayed on particular occasions for your reference: 1). You have connected to Internet successfully. 2). You might have entered a wrong user name and/or a wrong password. Please contact your ISP for the correct user name and password and enter them again. 3).
Wireless N150/N301 Easy Setup Router 4 Connect to Device Wirelessly Having finished above settings, you can search the device's wireless network (SSID) from your wireless devices (notebook, iPad, iPhone, etc) and enter a security key to connect to it wirelessly. WIN7 Operation 1. If you are using Windows 7 OS, do as follows: 1) Click Start and select Control Panel. 2) Click Network and Internet. 11 .
Wireless N150/N301 Easy Setup Router 3) Click Network and Sharing Center. 4) Click Change adapter settings. 12 .
Wireless N150/N301 Easy Setup Router 5) Select a desired wireless connection and click Connect/Disconnect. 6) Select the wireless network you wish to connect and click Connect. 13 .
Wireless N150/N301 Easy Setup Router 7) Enter the security key and click OK. 8) You can access Internet via the device when "Connected" appears next to the wireless network name you selected. 14 .
Wireless N150/N301 Easy Setup Router Windows XP Operation 2. If you are using Windows XP OS, do as follows: 1) Click Start and select Control Panel. 2) Click Network Connections. 15 .
Wireless N150/N301 Easy Setup Router 3) Right click Wireless Network Connection and then select View Available Wireless Networks. 4) Select the desired wireless network, click Connect, enter the security key and then click OK. 16 .
Wireless N150/N301 Easy Setup Router You can access Internet via the device when "Connected" appears next to the wireless network name you selected. 5) 17 .
Wireless N150/N301 Easy Setup Router Chapter 3 Advanced Settings 1 Advanced 1.1 Status Here you can see at a glance the operating status of the device. If WAN port displays Disconnected, please refer to 3 Verify Internet Connection Settings. 1.2 Internet Connection Setup PPPoE Select PPPoE (Point to Point Protocol over Ethernet) if you used to connect to the Internet using a broadband connection that requires a username and a password and enter the user name and password provided by your ISP. 18 .
Wireless N150/N301 Easy Setup Router Static IP Select Static IP if your ISP provides all the needed info. You will need to enter the provided IP address, subnet mask, gateway address, and DNS address(es) in corresponding fields. 1. Click Advanced. 2. Click Internet Connection Setup. 3. Internet connection Type: Select Static IP. 19 .
Wireless N150/N301 Easy Setup Router 4. IP Address: Enter the IP address provided by your ISP. Consult your ISP if you are not clear.Consult your ISP if you are not clear. 5. Subnet mask: Enter the subnet mask provided by your ISP. 6. Gateway: Enter the WAN Gateway provided by your ISP. 7. DNS Server: Enter the DNS address provided by your ISP. 8. OK: Click it to save all your settings.
Wireless N150/N301 Easy Setup Router 1. Internet connection Type: Displays the current Internet connection type. 2. PPTP Server Address: Enter the IP address of a PPTP server. 3. User Name: Enter your PPTP User Name. 4. Password: Enter the password. 5. MTU: Maximum Transmission Unit. DO NOT change it from the factory default of 1492 unless instructed by your ISP.
Wireless N150/N301 Easy Setup Router a) Internet connection Type: Displays the current Internet connection type. b) L2TP Server Address: Enter the IP address of a L2TP server. c) User Name: Enter your L2TP username. d) Password: Enter the password. e) MTU: Maximum Transmission Unit. DO NOT change it from the factory default of 1492 unless instructed by your ISP.
Wireless N150/N301 Easy Setup Router PPPoE Dual Access PPPoE dual access only supported in special Area e.g.Russia. 1. Internet connection Type: Displays the current Internet connection type. 2. PPPoE User Name: Enter the User Name provided by your ISP. 3. PPPoE Password: Enter the password provided by your ISP. 4. MTU: Maximum Transmission Unit. DO NOT change it from the factory default value unless necessary. 5. Service Name: Description of PPPoE connection. Leave blank unless otherwise required. 6.
Wireless N150/N301 Easy Setup Router 1.3 MAC Clone Some Internet service providers (ISPs) require end-user’s MAC address to access their network. This feature copies the MAC address of your network device to the router. 1. MAC Address: Configure device’s WAN MAC address. 2. Clone MAC Address: Click to copy your PC's MAC address to the device as a new WAN MAC address. 3. Restore Default MAC: Reset device’s WAN MAC to factory default. 1.4 WAN Speed Here you can set the speed and duplex mode for WAN port.
Wireless N150/N301 Easy Setup Router 1. LAN MAC Address: Displays device's LAN MAC address, which is NOT changeable. 2. IP Address: Device's LAN IP address. The default is 192.168.0.1. You can change it according to your need. 3. Subnet Mask: Device’s LAN subnet mask, 255.255.255.0 by default. 4. OK: Click to save your settings. Note：If the default IP address is changed, you must enter the new IP address to log in. 1.6 DNS Settings DNS is short for Domain Name System or Domain Name Service. 1.
Wireless N150/N301 Easy Setup Router 4. OK: Click to save your settings. Note: 1. Web pages are not able to open if DNS server addresses are entered incorrectly. 2. Do remember to reboot the device to activate new settings when you finish all settings. 1.7 DHCP Server The Dynamic Host Configuration Protocol (DHCP) is an automatic configuration protocol used on IP networks.
Wireless N150/N301 Easy Setup Router 1. IP Address: Enter the IP address for static DHCP reservation. 2. MAC Address: Enter the MAC address of a computer to always receive the same IP address (the IP you just specified). 3. Add: Click to add the entry to the MAC address reservation list. 4. OK: Click to save your settings.
Wireless N150/N301 Easy Setup Router 2 Wireless Settings 2.1 Wireless Basic Settings If you want to create a WLAN for sharing Internet connection, simply click Wireless-> Wireless Basic Settings. Change the SSID, you can name it whatever you like. For example, select 2437MHz (channel 6) and leave other options unchanged and then click OK. 1. SSID: This is the public name of your wireless network. The default is Tenda_XXXXXX. XXXXXX is the last six characters in the device's MAC address.
Wireless N150/N301 Easy Setup Router accesses and malicious packet sniffing. To encrypt your wireless network, do as follows: 1. Select the wireless network (SSID) you wish to encrypt. 2. Disable WPS. (WPS is enabled on the router by default. If you want to use other security modes, you must first disable the WPS.) 3. Select a proper security mode and cipher type (also known as WPA Algorithm or WPA Encryption Type).
Wireless N150/N301 Easy Setup Router WPS/PBC on the client device within 2 minutes; PIN: On the wireless security page, enable WPS, select PIN and enter the 8-digit PIN code from network adapter; then, within 2 minutes, enable WPS/PIN on the client device; Note： 1. With WPS successfully enabled, the WPS LED on the router keeps blinking for about 2 minutes, and during this time, you can enable WPS on a wireless 30 .
Wireless N150/N301 Easy Setup Router adapter; if the adapter successfully joins the wireless network, the WPS LED will display a solid light. Repeat steps above if you want to add more wireless adapters to the router. 2. Reset OOB: Clicking this button will reset SSID to factory default and disable security mode. 3. Existing wireless settings will still be maintained by default after a successful WPS connection. Namely security settings and SSID on the router will still be the same.
Wireless N150/N301 Easy Setup Router 2. Click Open Scan, select the AP you wish to connect, such as Tenda-000248, and click OK. 3. View and note down the wireless security settings: security mode, cipher type, security key. 32 .
Wireless N150/N301 Easy Setup Router 4. Click Close Scan and OK. 5. Save the settings and the router will reboot automatically. 6. Internet Connection Setup: Click Advanced>Internet Connection Setup, select Internet Connection Setup, such as DHCP, and click OK. 33 .
Wireless N150/N301 Easy Setup Router 7. Click Advanced>Status and the connection status displays Connected. Note： When the settings finished, remember to enter Internet Connection Setup to set up Internet connection. 2. Verify that the SSID, channel, and security mode on the page match those of the added wireless network. If not, manually correct them. 3.
Wireless N150/N301 Easy Setup Router extender mode and click Open Scan. 2. Click Open Scan, select the AP you wish to connect, such as Tenda-15058C, and click OK. 3. View and note down the wireless security settings: security mode, cipher type, security key, etc., which should be in accordance with the upper device. 4. Click Close Scan and OK. 35 .
Wireless N150/N301 Easy Setup Router 5. Save the settings and the router will restart automatically. WDS Bridge Mode Wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11 network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for a wired backbone to link them. Note: The Access Points you select must support WDS. 36 .
Wireless N150/N301 Easy Setup Router For example: As seen in the figure above, PC1 and PC2 access Internet via a wireless connection to Router 1. While PC3 and PC4 are too far to directly connect to Router 1 for Internet access. Now you can use the WDS bridge feature to let PC3 and PC4 access Internet. Before you get started: 1. View and note down the wireless security settings: security mode, cipher type, security key, etc. on Router 1; Click Status>LAN Settings and check the IP address. 2.
Wireless N150/N301 Easy Setup Router 3.Click Wireless>Wireless Security to check router one’s wireless security settings. 4. Verify that DHCP server is enabled on Router 1: Click Advanced>DHCP Server. 38 .
Wireless N150/N301 Easy Setup Router 5.Set the LAN IP address of Router 2 to a different address yet on the same net segment as Router 1. As shown below: Router 1: LAN IP: 192.168.0.1; Subnet Mask: 255.255.255.0; Router 2: LAN IP：192.168.0.10; Subnet Mask: 255.255.255.0; Then do as follows: 1. Configure Router 2: 1) Wireless Working Mode: Select WDS Bridge Mode. 2) Click Open Scan to search for Router 1. 39 .
Wireless N150/N301 Easy Setup Router 3) Select the wireless network to connect and click OK. 4) Verify that the SSID, channel, and AP MAC address on the page match those of the added wireless network. If not, manually correct them. 5) Close Scan and click OK to save your settings. 6) Go to Wireless Security page and set the wireless security settings exactly as they are on the link partner (Router 1). 7) Go to DHCP Server to disable the DHCP on Router 2.
Wireless N150/N301 Easy Setup Router 2. Configure Router 1: Go to wireless section on Router 1 and specify WDS (or WDS Bridge) as its wireless working mode. 2. Manually enter Router 2's MAC address (Also, you can use the Scan option as mentioned above) and click OK to finish your settings. 1. 2.4 Wireless Access Control The Access Control feature allows you to specify a list of devices to Permit or Forbid a connection to your wireless network via the devices’ MAC addresses.
Wireless N150/N301 Easy Setup Router 3. To permit a wireless device to connect to your wireless network, select Permit, enter its MAC address, click Add and then OK. Then only this device listed as “Permitted” will be able to connect to your wireless network; all other wireless devices will forbidden. Example: To forbid the PC at the MAC address of C8:3A:35:65:82:E6 from connecting to your wireless network, do as follows: Step1. Select an SSID, say, Tenda_178ED8. Step2.
Wireless N150/N301 Easy Setup Router Note: The bandwidth here refers to the channel bandwidth instead of wireless connection rate. 43 .
Wireless N150/N301 Easy Setup Router 3 Bandwidth Control 3.1 Bandwidth Control Use this section to manage bandwidth allocation to devices on your LAN. If there are multiple PCs behind your router competing for limited bandwidth resource, then you can use this feature to specify a reasonable amount of bandwidth for each such PC, so that no one will be over stuffed or starved to death. 1. Enable Bandwidth Control: Check or uncheck the box to Enable or disable the bandwidth control feature. 2.
Wireless N150/N301 Easy Setup Router 7. OK: Click to activate your settings. For example: If you are sharing a 4M broadband connection with a neighbor, who always exhausts the bandwidth resource downloading data, this feature will help. Simply specify half of the 4M bandwidth for your neighbor's PC (say, 192.168.0.100) and you will no longer need to struggle for bandwidth and your neighbor will only get up to 2M bandwidth. To do so, follow instructions below: 1. Check Enable. 2. Input "192.168.0.
Wireless N150/N301 Easy Setup Router Sent Message: Displays the number of packets sent by a corresponding PC via the device since Statistics is enabled. Sent Bytes: Displays the number of Bytes sent by a corresponding PC via the device since Statistics is enabled. The unit is MByte. Received Message: Displays the number of packets received by a corresponding PC via the device since Statistics is enabled.
Wireless N150/N301 Easy Setup Router 4 Special Applications 4.1 Port Range Forwarding Port range forwarding is useful for web servers, ftp servers, e-mail servers, gaming and other specialized Internet applications. When you enable port forwarding, the communication requests from the Internet to your router’s WAN port will be forwarded to the specified LAN IP address.
Wireless N150/N301 Easy Setup Router 2. LAN IP: Specify the internal host’s IP address. Be sure to statically assign the host’s IP address to make this function constant. 3. Protocol: Specify the protocol required for the service utilizing the port(s). 4. Enable: Check to enable current settings. 5. OK: Click to activate your settings. Now, your friends only need to enter ftp://xxx.xxx.xxx.xxx:21 in their browsers to access your FTP server xxx.xxx.xxx.xxx is the router's WAN IP address. Assuming it is 172.
Wireless N150/N301 Easy Setup Router Note: If you include port 80 on this section, you must set the port for remote (web-based) management to a different number than 80, such as 8080, otherwise the virtual server feature may not take effect. 4.2 DMZ Host The DMZ (De-Militarized Zone) function disables the firewall on the router for one device for a special purpose service such as Internet gaming or video conferencing. Enabling DMZ host may expose your local network to potential attacks.
Wireless N150/N301 Easy Setup Router communicated to the DDNS provider by software running on a computer or network device at that address; the provider distributes the association between the host name and the address to the Internet's DNS servers so that they may resolve DNS queries. Thus, uninterrupted access to devices and services whose numeric IP address may change is maintained. (You need to have an account with one of the Service Providers in the drop-down menu first.
Wireless N150/N301 Easy Setup Router application on the LAN. This feature is enabled by default. No settings are required. Enable UPnP: Check/uncheck to enable/disable the UPnP feature. OK: Click to complete your settings. 4.5 Static Routing When there are several routers in the network, you may want to set up static routing. Static routing determines the path of the data in your network. You can use this feature to allow users on different IP domains to access the Internet via this device.
Wireless N150/N301 Easy Setup Router 3. Gateway: Specif the IP address for next hop. 4. OK: Click to activate your settings. Note: 1. Gateway must be on the same IP net segment as device's LAN/WAN IP address. 2. Subnet Mask must be entered 255.255.255.255 if destination IP address is a host. 3. Subnet Mask must be entered accordingly if destination IP address represents an IP network segment. It must correspond to the specified IP address. For example, for IP address of 10.0.0.
Wireless N150/N301 Easy Setup Router 5 Security 5.1 URL Filter To better control LAN PCs, you can use the URL filter functionality to allow or disallow such PCs to access certain websites within a specified time range. 1. Filter Mode: Select a proper filter mode, say, Forbid Only. 2. Access Policy: Select an access policy number, say, 1, from the drop-down list. 3. Policy Name: Briefly describe the current rule, say, baidu, (It can only consist of numbers, letters, or underscore). 4.
Wireless N150/N301 Easy Setup Router 1. Filter Mode: Select Forbid Only. 2. Access Policy: Select an access policy number, say, 1, from the drop-down list. 3. Policy Name: Briefly describe the current rule, say, baidu, (It can only consist of numbers, letters, or underscore). 4. Start IP/End IP: Enter 2-254. 5. URL Character String: Enter baidu. 6. Time: Select 8:00-18:00.Day(s): Select Monday to Friday. 7. Enable: Check the Enable box. 8. OK: Click to save your settings.
Wireless N150/N301 Easy Setup Router 3. Policy Name: Briefly describe the current rule (It can only consist of numbers, letters, or underscore). 4. MAC Address: Specify a MAC address for a corresponding MAC filter rule to apply to. 5. Time: Specify a time period for a current rule to take effect. If the field is set to 0:00-0:00, the rule will be applied 24hrs/day. 6. Day(s): Select a day or several days for a current rule to take effect. If Sun-Sat is selected, the rule will apply 7days/week. 7.
Wireless N150/N301 Easy Setup Router 5.3 Client Filter This section allows you to set the times specific clients can or cannot access the Internet via the devices’ assigned IP addresses and service port. Forbid Only: Only PCs listed as Forbidden will be forbidden from accessing specified services; others are not restricted; Permit Only: Only PCs listed as permitted will be permitted to access specified services; others will be forbidden. Filter Mode: Select Permit Only.
Wireless N150/N301 Easy Setup Router 192.168.0.100--192.168.0.120 from accessing Internet, do as follows: 1. Filter Mode: Select Forbid Only. 2. Access Policy: Select an access policy number, say, 1, from the drop-down list. 3. Policy Name: Briefly describe the current rule, say, 123. 4. Start IP: Enter 100. 5. End IP: Enter 120. 6. Port: Enter 1-65535 to forbid all Internet services and applications. 7. Type (or Protocol): Select Both. 8. Time: Select 0 for all fields to apply the rule 24hrs/day. 9.
Wireless N150/N301 Easy Setup Router 6 Tools 6.1 Reboot Reboot the device to activate your settings. WAN connection will be disconnected during reboot. 6.2 Restore to Factory Default Settings Click the Restore to Factory Default button to reset device to factory default settings. You need to reconfigure the device for Internet access as well as many other settings including wireless settings. The factory default settings are listed below: IP Address: 192.168.0.1 Subnet mask: 255.255.255.0.
Wireless N150/N301 Easy Setup Router be imported to your device in case that the device is restored to factory default settings. To do so, follow below instructions: 1.Click the Backup button and specify a directory to save settings on your local hardware. 2.Click OK to save the configuration file. To restore previous settings, do as follows: Click the Browse button to locate and select a configuration file that is saved previously to your local hard drive. 59 .
Wireless N150/N301 Easy Setup Router Click the Restore button to reset your device to previous settings. 6.4 Syslog Here you can view the history of the device’s actions. After 150 entries, the earliest logs will clear automatically. 6.5 Remote Web Management The Remote management allows the device to be configured and managed 60 .
Wireless N150/N301 Easy Setup Router remotely from the Internet via a web browser. 1. Enable: Check/uncheck to enable/disable the DMZ host feature. 2. Port: This is the management port to be open to outside access. The default setting is 8080. Do NOT change it unless instructed by your ISP. 3. IP Address: Here you can specify the IP Address Range for remote management (When set to 0.0.0.0, the device becomes remotely accessible to all the PCs on Internet or other external networks). 4.
Wireless N150/N301 Easy Setup Router Note: Configured time and date info will be lost when the device gets disconnected from power supply. However, it will be updated automatically when the device reconnects to Internet. To activate time-based features (e.g. firewall), the time and date info shall be set correctly first, either manually or automatically. 6.7 Login Password This section allows you to change login password for accessing device’s Web-based interface for better security. 1.
Wireless N150/N301 Easy Setup Router 6.8 Firmware Upgrade Firmware upgrade is released periodically to improve the functionality of your device and also to add new features. If you run into a problem with a specific feature of the device, log on to our website (www.tendacn.com) to download the latest firmware to update your device. 1.Browse: Click to locate and select the firmware. 2. Upgrade (or Update): Click to update firmware. Device will restart automatically when update completes. Note: 1.
Wireless N150/N301 Easy Setup Router Appendix 1 Glossary Channel A communication channel, also known as channel, refers either to a physical transmission medium such as a wire or to a logical connection over a multiplexed medium such as a radio channel. It is used to transfer an information signal, such as a digital bit stream, from one or more transmitters to one or more receivers. If there is only one AP in the range, select any channel you like. The default is Auto.
Wireless N150/N301 Easy Setup Router protocols. It provides an authentication mechanism to devices wishing to attach to a LAN or WLAN.IEEE 802.1X defines the encapsulation of EAP over LAN or EAPOL. 802.1X authentication involves three parties: a supplicant, an authenticator, and an authentication server.
Wireless N150/N301 Easy Setup Router computer hostnames into IP addresses. WDS A wireless distribution system (WDS) is a system enabling the wireless interconnection of access points in an IEEE 802.11 network. It allows a wireless network to be expanded using multiple access points without the traditional requirement for a wired backbone to link them.
Wireless N150/N301 Easy Setup Router Appendix 2 Verify the WDS Connection Configure PC2: Click Start> Run on PC3, input cmd on the appearing window and then click OK. Input ping 192.168.0.1 and press Enter. 67 .
Wireless N150/N301 Easy Setup Router Configure PC3 and PC4： Set PC3 and PC4 to Obtain an IP address automatically. 1. 68 .
Wireless N150/N301 Easy Setup Router 2. When the two PCs get IP addresses, try below steps to verify the WDS connection: Click Start-> Run on PC3, input cmd on the appearing window and then click OK. Input ping 192.168.0.1 and press Enter. If you get a screen as seen below, you have successfully implemented WDS. 69 .
Wireless N150/N301 Easy Setup Router Note: 1. WDS feature can only be implemented between 2 WDS-capable wireless devices. Plus, SSID, channel, security settings and security key must be exactly the same on both such devices. 2. To ensure a proper wireless connection, do not change any settings on the two devices after WDS is successfully implemented. 70 .
Wireless N150/N301 Easy Setup Router Appendix 3 FAQs This section provides solutions to problems that may occur during installation and operation of the device. Read the following if you are running into problems. If your problem is not covered here, please feel free to go to www.tendacn.com to find a solution or email your problems to: support@tenda.com.cn or support02@tenda.com.cn. We will be more than happy to help you out as soon as possible. 1.
Wireless N150/N301 Easy Setup Router Internet connection type. You need to change the MTU size (1492 by default). In this case, go to “WAN Settings” to change the MTU value from default 1480 to 1450 or 1400, etc. 5. Q: How do I share resources on my computer with users on Internet through the device? To let Internet users access internal servers on your LAN such as e-mail server, Web, FTP, via the device, use the "Virtual Server" feature.
Wireless N150/N301 Easy Setup Router Appendix 4 Remove Wireless Network from Your PC If you change wireless settings on your wireless device, you must remove them accordingly your PC; otherwise, you may not be able to wirelessly connect to the device. Below describes how to do remove a wireless network from your PC. If you are using Windows XP, do as follows: 1.Right click "My Network Places" and select "Properties". 2.Click “Wireless Network Connection” and then select “Properties”. 73 .
Wireless N150/N301 Easy Setup Router 3.Click "Wireless Networks", select the item under "Preferred networks" and then click the Remove button. If you are using Windows 7, do as follows: 1.Click Network from your desktop and select Properties. 74 .
Wireless N150/N301 Easy Setup Router 2.Select "Manage Wireless Networks". 3. Click the wireless connection and select "Remove network". 75 .
Wireless N150/N301 Easy Setup Router Appendix 5 Safety and Emission Statement CE Mark Warning This is a Class B product In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device complies with EU 1999/5/EC. FCC Statement This device complies with Part 15 of the FCC Rules.
Wireless N150/N301 Easy Setup Router uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. NOTE: 1. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. 2. To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. 77 .
