1N Wireless Broadband Router 1
11N Wireless Broadband Router Copyright Statement is the registered trademark of Shenzhen Tenda Technology Co., Ltd. All the products and product names trademarks or mentioned registered herein trademarks are of the their respective holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
11N Wireless Broadband Router Contents Chapter 1: Introduction ............................................... 1 1.1 Product Features .............................................. 2 1.2 Package Contents ............................................. 4 1.3 LED Indicator and Port Description ...................... 4 Chapter 2 Hardware Installation.................................... 7 2.1 How to Install the Router..................................... 7 2.2 Network Application Plan ...........................
11N Wireless Broadband Router 6.1 Basic Settings.................................................. 26 6.2 Wireless Security Setting................................... 28 6.3 Advanced Settings............................................ 31 6.4 WPS Settings................................................... 32 6.5 WDS Settings .................................................. 35 6.6 Wireless Access Control..................................... 36 6.7 Connection Status .........................................
11N Wireless Broadband Router 11.3 MAC Address Filter........................................ 50 11.4 Prevent Network Attack ................................... 52 11.5 Remote Web Management ............................... 53 11.6 WAN Ping .................................................... 54 Chapter12 Routing Setting ......................................... 55 12.1 Routing Table ................................................. 55 Chapter 13 System Tools ...........................................
11N Wireless Broadband Router Chapter 1: Introduction Thank you for purchasing Tenda 11N Wireless Broadband Router! W268R utilizes advanced MIMO technology and increases over 8 times transmission range of ordinary 802.11g products. Compatible with IEEE802.11n (Draft 4.0) and IEEE802.11g/b standards, it can provide up to 150Mbps stable transmission rate.
11N Wireless Broadband Router life and QoS bandwidth control over specific computer’s downloading speed is supported as well. Moreover, UPnP and WMM support can smooth your MSN voice better, and the included Setup Wizard on CD-ROM will be easy and fast for non-savvy users to install the device and access to the Internet. 1.
11N Wireless Broadband Router ¾ Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports ¾ Supports xDSL/Cable MODEM, static and dynamic IP in community networking ¾ Supports remote/local Web management ¾ Supports WMM to better smooth your voice and video ¾ Supports SSID stealth mode and access control based over MAC address (up to 30 entries) ¾ Supports Auto MDI/MDIX ¾ Supports wireless Roaming technology for high-efficient wireless connections ¾ Supports auto negotiation/manual mode
11N Wireless Broadband Router 1.2 Package Contents Please unpack the box and check the following items: ¾ One W268R 11N Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One CD-ROM If any of listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately. 1.
11N Wireless Broadband Router SYS When turns green, blinking indicates the system runs well. WPS When blinking, it indicates the device is negotiating with client in WPS mode. WLAN Wireless signal LED indicator. When turns green, blinking indicates the wireless function is enabled; LAN (4,3,2,1) Wired local network LED indicator. Always ON indicates it is connected with Ethernet device; blinking indicates the device is transmitting and/or receiving data. WAN Wide area network indicator.
N Wireless Broadband Router Rear Panel：（From L to R） POWER The jack is for power adapter connection. Please use the included 9V DC power adapter. WAN A 100Mbps Ethernet port, can be connected with MODEM, Switch, Router and other Ethernet device for Internet connecting to DSL MODEM, Cable MODEM and ISP. LAN (1, 2, 3, 4) 4 10/100Mbps Ethernet ports can be connected with Ethernet switch, Ethernet router and NIC card. RESET The system reset button.
11N Wireless Broadband Router Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the box, please follow the steps below to connect. For better wireless performance, please put the device in the middle of wireless coverage area. 1. Please use the included power adapter to power on the Router. IMPORTANT: Use of a different power adapter could cause damage and void the warranty for this product. 2.
11N Wireless Broadband Router 3. Please connect your broadband line provided by your ISP to the WAN port. 4. Insert the included CD-ROM into the CD-ROM drive, double click the “Setup” icon and follow the instructions to complete the installation. Or you can enter the Router’s Web page to configure it. (More details please refer to Chapter 3.
11N Wireless Broadband Router 2.2 Network Application Plan Usually wireless LAN Network is deployed in a planned environment where each access point is located in a steady place with certain wireless coverage area for communication service. Generally speaking, it is in the center of the area to reduce “dead spot”.
11N Wireless Broadband Router Chapter 3 How to Login to the Router The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation, the following steps will assist you to set the network configurations for you computer. 3.1 How to Set the Network Configurations 1. On your computer desktop right click “My Network Places” and select “Properties”. 2. Right click “Local Area Network Connection” and select “Properties”.
11N Wireless Broadband Router 3 ． Select “Internet Protocol (TCP/IP)” and click “Properties”. 4 ． Select “Obtain an IP address automatically” and “Obtain DNS server address automatically”. Click “OK” to save the configurations.
11N Wireless Broadband Router Or select “Use the following IP address” and enter the IP address, Subnet mask, Default gateway as follows: IP Address: 192.168.0.XXX：(XXX is a number from 2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 Certainly you need to input the DNS server address provided by your ISP. Otherwise, you can use the Router’s default gateway as the DNS proxy server. Click “OK” to save the configurations. 3.2 Login to the Router 1.
11N Wireless Broadband Router 2． Input the “admin” in both User Name and Password. Click “OK”. 3. If you enter the correct user name and password, the screen will be the next one.
11N Wireless Broadband Router Chapter 4: Quick Setup Guide This chapter deals with how to access the Internet quickly. Please follow this guide to connect your Router to the Internet. 4.1 Setup Wizard 1. Here is the “Welcome to Setup Wizard” for configuring your Router quickly. Click “Next”. 2. In this screen, select one mode of your Internet connection you use. If you are not clear, press the “Detect” button or contact your Internet Service Provider, and click “Next”.
11N Wireless Broadband Router ADSL Virtual Dial-up (Via PPPoE) Enter the Account and Password provided by your ISP, and click “Next”. For example： Dynamic IP (Via DHCP) If your connection mode is Dynamic IP, it means your IP address keeps changing every time you connect. You do not need to enter the information like other modes. Click “Next” and “Save” to finish the settings.
11N Wireless Broadband Router DNS server fields and click “Next”. For example： ISP provides the following TCP/IP parameters as follows： IP Address：192.168.1.2 Subnet Mask：255.255.255.0 Gateway：192.168.1.1 Primary DNS Server：192.168.1.2 Alternate DNS Server：202.96.134.133 Click “Save” to complete the setup wizard. The Router will record the settings you made. To activate the settings, it is recommended to select “Reboot the Router” from “System Tool” of the left menu.
11N Wireless Broadband Router Click the “System Status” in the left menu of the Web-based Utility to find out the current network and system information. If the “Connection Status” is “Connected”, Congratulations you on completing the Router’s basic settings. You are on the Internet now. If you want to configure more, please proceed to the following explanations for Advanced Settings. L2TP L2TP Server IP: Enter the Server IP provided by your ISP. User Name: Enter L2TP username.
11N Wireless Broadband Router IP Address: Enter the L2TP IP address supplied by your ISP. Subnet Mask: Enter the Subnet Mask supplied by your ISP. Default Gateway: Enter the Default Gateway supplied by your ISP. PPTP PPTP Server IP: Enter the Server IP provided by your ISP. User Name: Enter PPTP username provided by your ISP. Password: Enter PPTP password provided by your ISP. Address Mode: Select “Static” if your ISP supplies you with the IP address, subnet mask, and gateway.
11N Wireless Broadband Router 19
11N Wireless Broadband Router Chapter 5: Advanced Settings 5.1 LAN Settings LAN Settings are for the basic TCP/IP parameters of LAN ports. MAC Address: The Router’s physical MAC address as seen on your local network, which is unchangeable. IP Address: The Router’s LAN IP addresses (not your PC’s IP address). 192.168.0.1 is the default value. Subnet Mask: It’s shown the Router’s subnet mask for measurement of the network size. 255.255.255.0 is the default value.
11N Wireless Broadband Router 5.2 WAN Settings After you have selected the ISP connection type in “Setup Wizard” and you want to modify the related settings, here you can modify and configure the settings in details. Virtual Dial-up（PPPoE） Connection Mode: Show your current connection mode. Account: Enter them provided by your ISP. Password: Enter them provided by your ISP. MTU: Maximum Transmission Unit. It is the size of largest datagram that can be sent over a network.
11N Wireless Broadband Router default value is 1492. Do NOT modify it unless necessary. But if when some specific website or web application software can not be open or enabled, have a try to change the MTU value as 1450, 1400, etc. Service Name: It is defined as a set of characteristics that are applied to a PPPoE connection. Enter it if provided. Do NOT modify it unless necessary. AC Name: Enter it if provided. Do NOT modify it unless necessary.
11N Wireless Broadband Router Static IP If your connection mode, static IP is chosen, you can modify the following addressing information. IP Address: Here enter the WAN IP address provided by your ISP. Subnet Mask: Enter the WAN Subnet Mask here. Gateway: Primary DNS Server: Enter the Primary DNS server Enter the WAN Gateway here. provided by your ISP. Secondary DNS Server: Enter the secondary DNS.
11N Wireless Broadband Router 5.3 MAC Address Clone This page is for the Router’s MAC address to WAN. Some ISPs require end-user's MAC address to access their network. This feature copies the MAC address of your network device to the Router. MAC Address: The MAC address to be registered with your Internet service provider. Clone MAC Address: Register your PC's MAC address. Restore Default MAC Address: Restore to the default hardware MAC address.
11N Wireless Broadband Router 5.4 DNS Settings DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider. Please consult your Internet Service Provider for details if you do not have them. DNS: Click the checkbox to enable the DNS server. The Router’s DHCP sever will answer the client’s requests and distribute DNS address.
11N Wireless Broadband Router Chapter 6: Wireless Setting 6.1 Basic Settings Enable Wireless: Check to enable the Router’s wireless features; uncheck to disable it. You can also press the WLAN/WPS button to turn on/off the wireless function. Network Mode：Select one mode from the following. The default is 11b/g/n mode. 11b mode：Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps.
11N Wireless Broadband Router 54Mbps. 11b/g mode：Allow the 11b/g-compliant client device to connect with the AP with auto-negotiation speed, and 11n wireless client to connect the device with 11g speed. 11b/g/n mode：Allow 11b/g/n-compliant client device to connect with the AP with auto-negotiation speed. SSID：SSID (Service Set Identifier) is the unique name of the wireless network. This device has two SSID and the SSID is necessary.
11N Wireless Broadband Router 6.2 Wireless Security Setting It is used to configure the AP network’s security setting. Here presents the common six (ten in all) encryption methods, including Mixed WEP, WPA-personal, WPA2-personal, etc. 6.2.1 Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of digital keys (64 bits or 128 bits in length).
11N Wireless Broadband Router corresponding security encryption modes. WEP Key1~4 ： Set the WEP key with the format of ASCII and Hex. You can enter ASCII code (5 or 13 ASCII characters. Illegal character as “/” is not allowed.) Or 10/26 hex characters. Default Key：Select one key from the four configured keys as the current available one. 6.2.2 WPA-Personal WPA (Wi-Fi Protected Access), a Wi-Fi standard, is a more recent wireless encryption scheme, designed to improve the security features of WEP.
11N Wireless Broadband Router Integrity Protocol] or AES [Advanced Encryption Standard]. The default is TKIP mode. Pass Phrase ： Enter the encrypted characters with 8-63 ASCII characters. Key Renewal Interval：Set the key’s renewal period. 6.2.3 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) and WPA (Wi-Fi Protected Access).
11N Wireless Broadband Router 6.3 Advanced Settings This section is to configure the advanced wireless setting of the Router, including the Radio Preamble, 802.11g/n Rate, Fragmentation Threshold, RTS Threshold, etc. BG protection Mode: Auto by default. It is for 11b/g wireless client to connect 11n wireless network smoothly in a complicated wireless area. Basic Data Rates: For different requirement, you can select one of the suitable Basic Data Rates. Here, default value is (1-2-5.5.
11N Wireless Broadband Router defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting. The default size is 2346 bytes. It is recommended not to modify this value. RTS Threshold: RTS stands for “Request to Send”. This parameter controls what size data packet the frequency protocol issues to RTS packet. The default value of the attribute is 2346. It is recommended not to modify this value in SOHO environment.
11N Wireless Broadband Router secret keys by manual. In the “Wireless settings” menu, click “WPS settings” to enter the next screen. WPS settings：To enable or disable WPS function. The default is “disable”. WPS mode ： Provide two ways: PBC (Push-Button Configuration) and PIN code.
11N Wireless Broadband Router present, the WPS supports up to 32 clients access.) PIN：If this option is enabled, you need to enter a wireless client’s PIN code in the field and keep the same code in the WPS client. WPS Summary ： Show the current state of Wi-Fi protected setting, including authorized mode, encryption type, default key and other information. WPS Current Status：Idle means WPS in idle state. Start MSC process means the process has been started and waits for being connected.
11N Wireless Broadband Router 6.5 WDS Settings WDS (Wireless Distribution System) is used to expand wireless coverage area. This Router provides three modes: Lazy, Bridge and Repeater. Lazy: In this mode, the connected device can be Bridge mode or Repeater mode and enter the Router’s BSSID to establish the connection. Bridge: You can wirelessly connect two or more wired networks via this mode.
11N Wireless Broadband Router Pass phrase: Enter the encrypted key for wireless devices. AP MAC: Input the MAC address of another (opposing) wireless router you want to connect. NOTE: It is recommended that two wireless routers keep the same bandwidth, channel number, and security settings. Apply the settings and reboot the Router to activate it. 6.
11N Wireless Broadband Router Select “Close” to malfunction MAC address; “disable” to prevent the MAC addresses in the list from accessing the wireless network; “Allow” to allow the MAC address in the list to access the wireless network. MAC Address Management：Input the MAC address to implement the filter policy. Click “Add” to finish the MAC add operation. MAC list：Show the added MAC addresses. You can add or delete them. 6.
11N Wireless Broadband Router Chapter 7: DHCP Server 7.1 DHCP Settings DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”. So specifying the starting and ending address of the IP Address pool is needed.
11N Wireless Broadband Router 7.2 DHCP List and Binding The Static IP assignment is to add a specifically static IP address to the assigned MAC address. You can view the related information in the DHCP server list. IP Address: Enter the IP address which needs to be bound. MAC Address: Enter the MAC address of the computer you want to assign the above IP address. Click “Add” to add the entry in the list. Hostname: The name of the computer which is added a new IP address.
11N Wireless Broadband Router Chapter 8 Virtual Server 8.1 Port Range Forwarding This section deals with the port range forwarding mainly. The Port Range Forwarding allows you to set up a range of public services such as web servers, ftp, e-mail and other specialized Internet applications to an assigned IP address on your LAN.
11N Wireless Broadband Router Internet applications. IP Address: Enter the IP address of the PC where you want to set the applications. Protocol: Select the protocol (TCP/UDP/Both) for the application. Delete/Enable: Click to check it for corresponding operation. Well-Known Service Port: Select the well-known services as DNS, FTP from the drop-down menu to add to the configured one above. Add: Add the selected well-known port to the policy ID.
11N Wireless Broadband Router 8.2 DMZ Settings The DMZ function is to allow one computer in LAN to be exposed to the Internet for a special-purpose service as Internet gaming or videoconferencing. DMZ Host IP Address: The IP address of the computer you want to expose. Enable: Click the checkbox to enable the DMZ host. IMPORTANT: When the DMZ host is enabled, the firewall settings of the DMZ host will not function.
11N Wireless Broadband Router 8.3 UPNP Settings It supports latest Universal Plug and Play. This function goes into effect on Windows XP or Windows ME or this function would go into effect if you have installed software that supports UPnP. With the UPnP function, host in LAN can request the router to process some special port switching so as to enable host outside to visit the resources in the internal host. Enable UPnP: Click the checkbox to enable the UPnP.
11N Wireless Broadband Router Chapter 9 Traffic Control 9.1 Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration. Enable Traffic Control: To enable or disable the internal IP bandwidth control. The default is disabled. Interface: To limit the uploading and downloading bandwidth in WAN port.
11N Wireless Broadband Router IP Starting Address: The first IP address for traffic control. IP Ending Address: The last IP address for traffic control. Uploading/Downloading: To specify the traffic heading way for the selected IP addresses: uploading or downloading. Bandwidth: To specify the uploading/downloading Min. /Max. Traffic speed (KB/s), which can not exceed the WAN speed. Apply: To enable the current editing rule. If not, the rule will be disabled.
11N Wireless Broadband Router Chapter10 URL Monitor 10.1 URL Monitor This feature is used to record user’s Internet activity, so in terms of this feature, the administrator can check out and control what they can do and have done. Enable URL Monitor: After checking this feature, the Router will record LAN computer’s URL information, including the visiting Website, your LAN IP address and the time. The Router can record up to 500 entries.
11N Wireless Broadband Router will be sent to specified e-mail, which can be solved the problem that the records will be lost when it is over 500 entries. Receive E-mail Address: Input the received E-mail’s address here. For example: tenda@sina.com.cn SMTP Server Address: Input the SMTP server address here. If you are not clear what your SMTP server’s address is, you can find them from Help page of the registered e-mail. For example: smtp.sohu.com, smtp.163.com, etc.
11N Wireless Broadband Router Chapter 11: Security Settings 11.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. Client Filter: Check to enable client filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all settings for the policy.
11N Wireless Broadband Router Policy Name: Enter a name for the access policy selected. IP Start/End: Enter the starting/ending IP address. Port No.: Enter the port range based over the protocol for access policy. Protocol: Select one protocol (TCP/UDP/Both) from the drop-down menu. Times: Select the time range of client filter. Days: Select the day(s) to run the access policy. 11.
11N Wireless Broadband Router URL Filter: Check to enable URL filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all settings for the policy. Filter Mode: Click one radio button to enable or disable to access the Internet. Policy Name: Enter a name for the access policy selected. Start/End IP: Enter the starting/ending IP address.
11N Wireless Broadband Router MAC Address Filter: Check to enable MAC address filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all settings for the policy. Filter Mode: Click one radio button to enable or disable to access the Internet. Policy Name: Enter a name for the access policy selected. MAC Address: Enter the MAC address you want to run the access policy.
11N Wireless Broadband Router Days: Select the day(s) to run the access policy. Apply： Click to make the settings go into effect. For example: if you want to configure the host with MAC address 00:C0:9F: AD:FF:C5 not to access the Internet at 8：00-18：00, you need to set it as above. 11.4 Prevent Network Attack This section is to protect the internal network from exotic attack such as SYN Flooding attack, Smurf attack, LAND attack, etc.
11N Wireless Broadband Router 11.5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”. Enable: Check to enable remote web management. Port: The management port open to outside access. The default value is 80. WAN IP Address: Specify the range of the WAN IP address for remote management. Note： 1.
11N Wireless Broadband Router remote Web management. If you change the WAN IP address as 218.88.93.33-218.88.93.35, then only the IP addresses as 218.88.93.33, 218.88.93.34 and 218.88.93.35 can access the Router. For example: If you want to configure the IP address 218.88.93.33 to access the device’s web interface, please set it as follows: 11.6 WAN Ping The ping test is to check the status of your internet connection. When disabling the test, the system will ignore the ping test from WAN.
11N Wireless Broadband Router Chapter12 Routing Setting 12.1 Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e. routing arithmetic. In order to finish this function, many transferring paths, i.e. routing table, are saved in the router, for choosing when needed.
11N Wireless Broadband Router Chapter 13 System Tools 13.1 Time Settings This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet. Time Zone: Select your time zone from the drop-down menu. Customized time: Enter the time you customize. Note： When the Router is powered off, the time setting will be lost.
11N Wireless Broadband Router 13.2 DDNS The DDNS (Dynamic Domain Name System) is supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router. If you want to activate this function, please select “Enable” and a DDNS service provider to sign up.
11N Wireless Broadband Router User Name: Enter the user name the same as the registration name. Password: Enter the password you set. Domain Name: Enter the domain name which is optional. For example： In the local host 192.168.0.10 establish a Web server, and register in 3322.org as follows: User name tenda Password 123456 Domain Name tenda.vicp.net After mapping the port in the virtual server, setting account information in DDNS server and in the address field entering http://tenda.3322.
11N Wireless Broadband Router Backup Setting： Click “Backup” button to back up the Router’s settings and select the path for save. Click “Save” to save the configuration files. Restore Setting： Click “Browse” button to select the backup files.
11N Wireless Broadband Router Click “Restore” button to restore previous settings. 13.4 Restore to Factory Default Setting This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary. Restore: Click this button to restore to default settings. Factory Default Settings: User Name: admin Password: admin IP Address: 192.168.0.1 Subnet Mask: 255.255.255.
11N Wireless Broadband Router 13.5 Upgrade Firmware The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn. Browse: click this button to select the upgrade file. Upgrade: click this button to start the upgrading process. After the upgrade is completed, the Router will reboot automatically. 13.
11N Wireless Broadband Router 13.7 Password Change This section is to set a new user name and password to better secure your router and network. User Name: Enter a new user name for the device. Old Password: Enter the old password. New Password: Enter a new password. Re-enter to Confirm: Re-enter to confirm the new password. NOTE: It is highly recommended to change the password to secure your network and the Router.
11N Wireless Broadband Router 13.8 System Log The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically. Refresh: Click this button to update the log. Clear: Click this button to clear the current shown log. 13.9 Logout After you have finished the settings completely, in logout page click “Yes” to logout the web management page.
11N Wireless Broadband Router Appendix 1：Glossary Access Point(AP): Any entity that has station functionality and provides access to the distribution services, via the wireless medium(WM) for associated stations.
11N Wireless Broadband Router network. The 40bit and 64bit encryption are the same because of out 64 bits, 40 bits are private. Conversely, 104 and 128 bit are the same. WEP uses a common KEY to encode the data. Therefore, all devices on a wireless network must use the same key and same type of encryption. There are 2 methods for entering the KEY; one is to enter a 16-bit HEX digit. Using this method, users must enter a 10-digit number (for 64-bit) or 26-digit number (for 128-bit) in the KEY field.
11N Wireless Broadband Router Appendix 2: Ask and Question In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.cn, and we will reply you in the first time. 1、 Can not login to the Web interface of the Router after you enter the IP address in the address field？ 9 Step 1: check the Router if it works well.
11N Wireless Broadband Router 2、Forget the login password and can not enter the setting page. What can I do? 9 Press the “RESET” button for 7 seconds to restore the Router to default settings. 3、 The computer connected with the Router shows IP address conflict. What can I do? 9 Check if there are other DHCP servers in the LAN. If there have, disable them. The default IP address of the Router is 192.168.0.1 and please maker sure the address is not occupied by other devices.
11N Wireless Broadband Router 5 、 How to configure and access the Internet via Dynamic IP? 9 In Setup Wizard of the Web utility interface, select “Dynamic IP” connection type and click “Save” to activate it. As some ISPs bind the user computer’s MAC address, you need to clone the Router’s WAN MAC address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it.
11N Wireless Broadband Router 9 Step 5: Input the internal server’s IP address. If your Web server’s IP address is 192.168.0.10, please input it. 9 Step 6: select the communication protocol used by your internal host: TCP, UDP, ICMP. 9 Step 7: click “Apply” to activate the settings.
11N Wireless Broadband Router FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
11N Wireless Broadband Router “The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.” FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of FCC RF Rules.
