1N Wireless Broadband Router User Guide Wireless-N Broadband Router W316R Notice： RF Exposure Statement To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.
11N Wireless Broadband Router User Guide Copyright Statement is the registered tr ademark of Shenzhen Tenda Technology Co., Ltd. All the products and pr oduct names men tioned herei n are the tr registered t rademarks ademarks or of thei r respecti ve holders. Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co.
11N Wireless Broadband Router User Guide Contents CHAPTE R 1 PRODUCT INTRODUCTION .........................................1 1.1 PACK AGE C ONTE NTS.............................................................................2 1.2 LE D INDICATORS AND PORT D E SCRIPTION ......................................2 CHAPTE R 2 PRODUCT INSTALLAT ION............................................5 CHAPTE R 3 HOW TO CONFIGURE TO ACCE SS THE INT E RNE T ....................................................................
11N Wireless Broadband Router User Guide 6.1 DHCP SE TTINGS ..................................................................................49 6.2 DHCP C LIE NT L IST .............................................................................50 CHAPTE R 7 V IRT UAL SE RV E R ...........................................................52 7.1 PORT R ANGE F ORWARDING ............................................................... 52 7.2 DMZ SE TTINGS .........................................................
11N Wireless Broadband Router User Guide APPE NDIX 2 PRODUCT FE AT URE S .................................................85 APPE NDIX 3 FAQ ....................................................................................86 APPE NDIX 4 CLE AR WIRE LE SS CONFIGURATION ...................90 APPE NDIX 5 RE GULATORY INFORMATION ...............................
11N Wireless Broadband Router User Guide Chapter 1 Product Introduction Thank y ou for purchasing the T enda W316R Wireless Broadband Router! This easy -to-use router provi des si mple configuration interface which enables you to configure it with ease. It i s based on the l atest IEEE802. 11n standard, and i s backwar d compati ble wi th devi ces of IEEE802.11b/g standards.
11N Wireless Broadband Router User Guide 1.1 Package Contents Please veri fy the fol lowing i tems afte r you open the package: ¾ One W316R Wireless Broadband Router ¾ One Quick Installation Guide ¾ One Power Adapter ¾ One Software CD If any of the l isted i tems are mi ssing or damag ed, please contact the T enda resel ler for immediate replacement. 1.
11N Wireless Broadband Router User Guide LED indicator description on the front panel Back panel port show 3
11N Wireless Broadband Router User Guide Back panel port description 4
11N Wireless Broadband Router User Guide Chapter 2 Product Installation 1. Please use only the included power adapter to power y our r outer. ( NOTE: Use of an unmatched power adapter could cause damage tothis product). 2. Pl ease connect the router ’s LA N port to your computer with an Ethernet cable as shown below.
N Wireless Broadband Router User Guide 3. Please connect your broadband line provided by your ISP to the router’s WAN port. 4. Insert the included software CD into the CD drive of your computer . After t he software automati cally initiates, double click the “Setup” icon and follow the instructions t o compl ete the i nstallation. You can a lso enter the router ’s W eb-based Uti lity to compl ete the configuration.
11N Wireless Broadband Router User Guide Chapter 3 How to configure to access the Internet 3.1 How to Set the Network Configurations Network Configurations under windows XP 1. Right click “My Network Places” on your computer desktop and select “Properties”. 2. Right cli ck “ Local Area Connection ” and sel ect “Properties”.
11N Wireless Broadband Router User Guide 3. S elect “ Internet Pro tocol (TCP/IP) ” and click “Properties”. 4.
11N Wireless Broadband Router User Guide “Obtain D NS ser ver addr ess automatically ”. Click “OK” to save the configurations. Or select “Use the following IP address ” and enter the IP addr ess, Subnet mask, Defaul t gatewa y a s follows: ¾ IP Address: 192.168.0.XXX: (XXX i s a number from 2~254) ¾ Subnet Mask: 255.255.255.0 ¾ Gateway: 192.168.0.1 ¾ DNS se rver: You s hould in put t he DNS s erver address provided by your IS P. Otherwise, you can enter 1 92.168.0.1.
11N Wireless Broadband Router User Guide Network Configurations under windows 7 1. Cli ck the network i con on the l ower ri ght corner of your computer desktop, and then cli ck” Open Network and Sharing Center”.
11N Wireless Broadband Router User Guide 2. Click “Change adapter settings” on the left side of the window. 3. Ri ght click “Local Area Connecti on” and sel ect “Properties”.
11N Wireless Broadband Router User Guide 4. Double click” Internet Protocol Version 4(TCP/IPv4)".
11N Wireless Broadband Router User Guide 5. Select “Obtain an IP a ddress automatically” and “Obtain D NS ser ver addr ess automatically ”. Click “OK” to save the configurations.
11N Wireless Broadband Router User Guide ¾ IP Address: 192.168.0.XXX: (XXX i s a number from 2~254) ¾ Subnet Mask: 255.255.255.0 ¾ Gateway: 192.168.0.1 ¾ DNS se rver: You s hould in put t he DNS s erver address provided by your IS P. Otherwise, you can enter 1 92.168.0.1. Cli ck “OK” to save the configurations. 3.2 Log in to the Router 1. To access the R outer’s Web-based Utility, launch a web browser such as Internet Explorer or Firefox and enter http://192.168.0.1. Press “Enter”.
11N Wireless Broadband Router User Guide 2. Type “admin” in the “Password” field. Click “OK”. 3. If you enter the correc t password, you will come to the router’s web-based utility as is shown below.
11N Wireless Broadband Router User Guide 3.3 Fast Internet Access Two kinds of fast access methods are provided on the router’s web-based utility: ADSL dial-up and DHCP. If you select ADSL dial-up, you only need to enter the access accou nt and access password as we ll as the wireless password, and then click “Ok” to complete the settings. If you select DHCP, you only need to enter the wireless password and click “Ok” to complete the settings.
11N Wireless Broadband Router User Guide The defaul t access meth od i s A DSL dial-up and the access accou nt and access password are the same as the ADSL dial-up account and password, which you can inquire your broadband ISP. For other access methods, please refer t o WAN settings in chapter 4.The wi reless password can only consist of 8 characters, the default is 12345678 and you can modify it when necessary.
11N Wireless Broadband Router User Guide 3.4 Fast Encryption The router provi des two encryption s etting screens, one i s si mple and easy , the other i s adv anced (For advanced setting, please refer to chapter 5.2). Simple and easy screen: Log on to the router’s web-based utility and you may set encrypti on for the router. The defaul t adopts WPA-PSK mode and A ES Al gorithm. The def ault password is 12345678, as shown below.
11N Wireless Broadband Router User Guide Chapter 4 Advanced Settings 4.1 System Status System status screen al lows you to view the route r’s WAN port status and system status. Connection status: It di splays the router ’s WAN connection status. Disconnected: It i ndicates the router ’s W AN por t hasn’t been connected with the network cable. Connecting: It i ndicates the router ’s WAN port i s obtaining IP address. Connected: It i ndicates the R outer i s well connected with the ISP.
11N Wireless Broadband Router User Guide Connection type: It displays your current access method. LAN MAC address ：It di splays the R outer’s LA N MAC address. WAN MAC address：It displays the Router’s WAN MAC Address.
11N Wireless Broadband Router User Guide 4.2 WAN Settings Virtual Dial-up (PPPoE) ¾ Mode: Show your current connection mode. ¾ Access Ac count: Enter the account provided by your ISP. ¾ Access Pas sword: Enter the passwo rd provi ded by your ISP. ¾ MTU: Maximum Transmission Unit.
11N Wireless Broadband Router User Guide network. The default value is 1492. Do NOT modify it unless necessary, but if a specific website or web application s oftware c annot o pen o r b e e nabled, you can try to change theMTU value to 1450, 1400, etc. ¾ Service Name: The connecti on name for current PPPOE, enter i t if necessary ，otherwise, l eave it blank. ¾ AC Name: The service name, enter it if necessary， otherwise, leave it blank.
11N Wireless Broadband Router User Guide settings” from “System tools”. Static IP If your ISP provides you the stati c IP, pl ease cho ose static IP, and you need to enter the IP address, subnet mask, gateway, DNS serv er and al ternate DNS server provided by your ISP or network administrator。 ¾ Mode: Show your current connection mode. ¾ IP address: Enter the WAN IP address provided by your ISP. If y ou are not c lear, please inquire your local ISP.
11N Wireless Broadband Router User Guide ¾ DNS serv er: Enter th e necessary DNS server provided by your ISP. ¾ Alternate DNS serv er: Enter the second DNS address if your ISP provides, which is optional. Dynamic IP (Via DHCP) If your connection mode is Dynamic IP, it means every time you access the Internet, you will get a different IP. You don’t need to en ter any parameters in this mode, just Click “Ok” to finish the settings.
11N Wireless Broadband Router User Guide ¾ ¾ Mode: Show your current connection mode. PPTP server address: The IP address or domain name o f t he d estination server a nd it is u sed t o specify the desti nation addres s whi ch needs fo r PPTP connection. ¾ Username/Password: Used to v alidate i dentity when connecting to the PPTP server. ¾ Address mode: Set the router’s IP address mode, you can select either “Dynamic” or “Static”.
11N Wireless Broadband Router User Guide ¾ Subnet mask: Pl ease enter the subnet mask provided by your ISP ,generally its 255.255.255.0 ¾ Gateway: Please enter the gateway provided by your ISP, inquire your local ISP if you are not clear. All the above parameters are provided by ISP. L2TP ¾ ¾ Mode: Show your current connection mode. L2TP server address: The IP address or domain name o f t he d estination server a nd it is u sed t o specify the desti nation addres s whi ch needs fo r L2TP connection.
11N Wireless Broadband Router User Guide when connecting to the L2TP server. ¾ Address mode: Set the router’s IP address mode, you can select either “Dynamic” or “Static”. If your ISP doesn’ t provide the IP addre ss, pl ease sel ect “Dynamic”. ¾ IP address: Please enter the IP address provided by your I SP, inquire your local ISP if you a re n ot clear. ¾ Subnet mask: Pl ease enter the subnet mask provided by your ISP ,generally its 255.255.255.
11N Wireless Broadband Router User Guide 4.3 LAN Settings Click “ Advanced s ettings” –LAN s ettings to enter the following screen. ¾ LAN MAC address: The Router’s LAN MAC address, which is unchangeable. ¾ IP address: The Router’s LAN IP address (not your PC’s IP address).The default value is 192.168.0.1; you can change it when necessary. ¾ Subnet mask: The Router’s LAN subnet mask. The default value is 255.255.255.
11N Wireless Broadband Router User Guide 4.4 DNS Settings DNS stands for Domain Name System (or Service). ¾ DNS setting: Select to enable the DNS server. ¾ Primary DNS address: Enter the necessary address provided by your ISP. ¾ Alternate DNS address : Enter the s econd DNS address if your ISP provides, which is optional. NOTE: After the settings are completed, reboot the device to activate the modified settings.
11N Wireless Broadband Router User Guide 4.5 Bandwidth Control Bandwidth control is used to limit the communication traffic of LAN computers when accessing the Internet. It can simultaneously control maximum of 254 PCs' traffic. In addi tion, IP addres s r ange configuration i s supported. ¾ Enable Bandwidth Control: To enable or disable the i nternal IP bandwi dth control. The defaul t is disabled. ¾ IP Address: The IP add ress r ange of the hosts whose traffic has been controlled.
11N Wireless Broadband Router User Guide download. ¾ Bandwidth Range: The maximum and minimum upload/download data tr affic of the hosts i n specified IP range. The unit is KByte/s. The uplink of upload and downl oad can not exceed the W AN port bandwidth limitation range. ¾ Enable: To enabl e th e current edited rul e. Otherwise, the rule will not go into effect. ¾ Add to list: After you edit the rule, click the “add to list” button to add th e current rul e to the rul e list.
11N Wireless Broadband Router User Guide 1.Enter 192.168.0.100 in the IP address field 2.Select upload in the Upload/Download field. 3.Enter 10-15 in the bandwidth range field 4.Select “Enable” 5.Click “Add to list” 6.Click “Ok” to finish the upload rule settings. And then add a download rule as shown in the picture below.
11N Wireless Broadband Router User Guide The setting method is the same as the above. Example 2 Set the downl oad r ate of all computers within the r ange of 192 .168.0.2--192.168.0.254 as 100-120KByte/s, and the upload rate as 20-30KByte/s, as shown in the picture below.
11N Wireless Broadband Router User Guide The setting method is the same as Example 1.
11N Wireless Broadband Router User Guide 4.6 Traffic Statistics Traffic statistics is used to display the bandwidth that LAN PC used. Enable Traffic statistics: It is used to calculate the traffic used by the LAN computers. You can enable it to calculate the tr affic for you. Usua lly, di sable it to improve the router’s data packet processing ability, and the default is disabled.
11N Wireless Broadband Router User Guide second, the unit is KByte/s. ¾ Sent mess age: the number of the cal culated computer’s data packets that are sent out through the router. ¾ Sent Byt es: the vol ume of the cal culated computer’s statistics that i s sent out through the router ¾ Received message: the number of the calculated computer’s t he data pac kets that are recei ved through the router.
11N Wireless Broadband Router User Guide Chapter 5 WLAN Settings 5.1 Wireless Basic Settings ¾ Enable wireless functio n: Se lect t o enable t he Router’s wi reless features; desel ect to di sable it and all functions related with wireless are disabled.
11N Wireless Broadband Router User Guide drop-down list. 11b mode：Select it if you have only Wireless-B clients in your network. 11g mode：Select it if you have only Wireless-G clients in your network. 11b/g mixed mode: Select it i f you h ave o nly Wireless-B and Wireless-G clients in your network. 11b/g/n mixe d mode : Select it if y ou have Wireless-B, Wireless-G and Wi reless-N cli ents in your network. ¾ SSID: It is the un ique name of t he wi reless network and can be mod ified.
11N Wireless Broadband Router User Guide ¾ APSD Capa ble: It is used for auto power-saved service. The default is disabled. ¾ Channel b andwidth: channel ba ndwidth to Select an appropriate enhance the wi reless performance. Select 20/40M when the network has 11b/g and 11n wi reless c lients. Select 20M when the network has onl y n on-11n wi reless cl ients. Select 20/40M to promote its throughput when the wireless network is in 11n mode.
11N Wireless Broadband Router User Guide ¾ AP MAC ad dress: Input the MA C address of another (opposi ng) w ireless router y ou w ant to connect. Example: This example is to bridge two 316R routers. 1. If you know the connecti ng router ’s MA C address, please enter i t into the AP MAC address field and click “Ok”.
11N Wireless Broadband Router User Guide 2. You can also search for the wireless router’s signal by scanning. a) Click “Open scan” and cl ick the scanned si gnal and click the ”O k” button on the di alog bo x and the corresponding wi reless MA C address will be added to the AP MAC address field automatically.
11N Wireless Broadband Router User Guide b) Click “Ok” after the MAC address is added.
11N Wireless Broadband Router User Guide After fi nishing the abo ve steps, you need to set the other W316R router in the same way. NOTE: WD S feature requi res both routers support this function and the SSID, channel, encryption method and password are the same as those of the connecting router. 5.2 Wireless Security Settings With the wi reless securi ty funct ion, y ou can prev ent others from connecti ng to y our wi reless network and using the n etwork resources wi thout your cons ent.
11N Wireless Broadband Router User Guide intercepting or intruding your wireless network. 5.2.1 WPS Settings WPS (Wi-Fi Protected Setting) makes it quick and easy to establish a secure con nection between the wi reless clients and the router . The users onl y need to ente r a PIN cod e or press W PS b utton on the back panel to configure it without ma nually s electing a n e ncryption method or set a key. ¾ WPS settings: To enable or disable WPS function. The default is “Enable”.
11N Wireless Broadband Router User Guide ¾ WPS mode: Provide two ways: PBC (Push-Button Configuration) and PIN code. ¾ PBC: Select the PBC and cli ck Ok, or press and hold the WPS button on device for about one the back panel of the second. The WPS LED indicator will be fl ashing for 2 mi nutes, whi ch means t he WPS is e nabled. Du ring t his t ime (flashing W PS L ED), you can e nable t he wir eless client to implement the WPS/PBC negoti between the m.
11N Wireless Broadband Router User Guide ¾ WPA Algor ithms: Provides TKI P [Temporal K ey Integrity Pro tocol] or AE S [Adv anced Encrypti on Standard]. ¾ Key: Enter the pass phr ase that consi sts of 8-63 ASCII characters. ¾ Key Renewal Inter val: Set the key’ s renewal period, which tells the device how often it should change the dynamic keys.
11N Wireless Broadband Router User Guide 5.2.3 WPA2- PSK WPA2 (Wi -Fi Protected Access versi on 2) pro vides higher security than and WPA (Wi-Fi Protected Access). ¾ WPA Algor ithms: Provides TKI P [Temporal K ey Integrity Pro tocol] or AE S [Adv anced Encrypti on Standard]. ¾ Key: Enter the pass phr ase that consi sts of 8-63 ASCII characters. ¾ Key Renewal Inter val: Set the key’ s renewal period, which tells the device how often it should change the dynamic keys.
11N Wireless Broadband Router User Guide 5.3 Wireless Access Control Wireless access control is actual ly based on the MAC address to permit or forbid specific clients to access the wireless network. ¾ MAC addres s filter: “Permit” indicates to allow the clients in the list to access the wireless network, “Forbid” indicates to prevent the clients in the list from accessing the wireless network. ¾ Configure MAC address: Input the MAC addresses of the wireless clients to implement the filter policy .
11N Wireless Broadband Router User Guide 5.4 Connection Status This screen shows wi reless cl ient’s connecti on status, including MAC address, Channel bandwidth. ¾ MAC addres s: Shows the MAC addre sses of the hosts connected to the Router. ¾ Bandwidth: Shows the channel bandwidth of the current connected hosts (wireless clients). Chapter 6 DHCP Server 6.1 DHCP Server DHCP (Dynamic Host Control Protocol) is used to assign an IP addr ess to the co mputers on the LAN/pri vate network.
11N Wireless Broadband Router User Guide premise of acti vating “Obtai n an IP Address Automatically”. So specifying the start and end address of the IP Address pool is needed. ¾ DHCP s erver: Check the Enable box to enabl e DHCP server. ¾ IP pool start/end address: Enter the range of IP addresses for DHCP server distribution. ¾ Lease time: It i ndicates the v alid t ime of the dynamic IP address whi ch i s d istributed to the DHCP c lient’s host com puter by DHCP serv er.
11N Wireless Broadband Router User Guide are assi gned by the DHCP server . Y ou can manu ally enter the IP and MAC address and convert them to static assignment. ¾ Host name: It displays the name of the computer whose IP is allocated by the DHCP server. ¾ IP address: Enter the I P add ress w hich needs static binding. ¾ MAC address: Enter th e MAC address of the computer you want to bind. Click “Add” to add the entry in the list.
11N Wireless Broadband Router User Guide Chapter 7 Virtual Server 7.1 Port Range Forwarding ¾ Start/End port: Enter the start/end port number which r anges the Externa l ports used to set th e server or Internet applications. ¾ LAN IP: Enter the IP address of the PC which you want to set as the server. ¾ Protocol: Select the prot ocol (TCP/UDP/Both) for the appl ication.
11N Wireless Broadband Router User Guide protocol you are using, you can select “Both”. ¾ Enable: Click the Enable checkbox to bring the set rule into effect. ¾ Delete: Clear all settings of this item. ¾ Well-known service protocol ports are port: The well -known listed in the drop-down li st. Select one and select a sequence number in the ID drop-down list and then click “Add”, this port will be added autom atically to th e ID l ist.
11N Wireless Broadband Router User Guide and its port 21 will be added to the corresponding field automatically. 2. Enter 192. 168.0.10 in the LA N IP col umn, and then select “Both” as the protocol and select “Enable”. 3. As the picture shown below. 4. Click the “Ok” button to save the settings. And now, when your friends want to visit the FTP server, they only need to enter ftp://xxx.xxx.xxx.xxx:21 in the address field. Here, xxx.xxx.xxx.xxx means the router’s WAN IP address.
11N Wireless Broadband Router User Guide ftp://172.16.102.89:21 in the address field. NOTE: If you set theservice port of the virtual server as 80, you must set the Web management port on Remote Web Management screen to be any value except 80 such as 8080. Otherwise, there will be a conflict to disable the virtual server.
11N Wireless Broadband Router User Guide 7.2 DMZ Settings The DMZ Setti ngs screen all ows one local computer to be exposed to the Internet for use of a special-purpose service such as Internet gaming or vi deoconferencing. DMZ hosting forwards all the ports at the same time to one PC. ¾ DMZ Host IP Address: The IP address of the LAN computer you want to set as DMZ host. ¾ Enable: Check to enable the DMZ host. For example: Set the computer at the IP address of 192.168.0.
11N Wireless Broadband Router User Guide 7.3 UPNP Settings UPnP (Universal Plug and Play).With the UPnP function, the internal host can request the routerto process some special port switching so as to enable the external host to visit the resources of the internal host. ¾ Enable UPnP: Cli ck the checkbox to enabl e the UPnP. NOTE: This function goes into effect under Windows XP or Windows ME (NOTE: the system should integrate or have installed the Directx 9.
11N Wireless Broadband Router User Guide Chapter 8 Security Settings 8.1 Client Filter Settings You can ena ble cli ent f ilter to control LAN computers’ access to some ports of the Internet。 ¾ Filter Mode: You can select either “Permit only” or “Forbid only”. ¾ Access Poli cy: Sel ect one number from the drop-down list. ¾ Remark: A simple description of the configured file. You can also leave it blank. ¾ Start/End IP: Enter the start/end IP address.
11N Wireless Broadband Router User Guide ¾ Port: Enter the controll ed TCP/UDP protocol port. You can specify a port or port range. ¾ Type: Sel ect one protoco l (T CP/UDP/Both) from the drop-down list. ¾ Time: Select the time range of client filter. ¾ Date: Select the day(s) to run the access policy. ¾ Enable: T o e nable/disable t he a ccess p olicy (forbid/permit the pack ets matched wi th the access policy to pass through the router. Example1 Forbid LAN computers at the IP addresses of 192.
11N Wireless Broadband Router User Guide 18:00 from Sunday to Saturday. 8.2 MAC Address Filter You can limit the computer’s access to Internet by MAC Address Filter.
11N Wireless Broadband Router User Guide ¾ Filter mode: You can select either “Permit only” or “Forbid only”. ¾ Access Poli cy: Sel ect one number from the drop-down list. ¾ Remark: A simple description of the configured file. You can also leave it blank. ¾ MAC Address: Enter the MAC address you want to run the access policy. ¾ Time: S elect the ti me r ange of M AC address filter. ¾ Date: Select the day(s) to run the access policy.
11N Wireless Broadband Router User Guide of 00:E0:4C:69:A3:23 to access Internet during 8:00 to 18:00 from Monday to Friday. Example 2 Permit the computer with the MAC address of 00 ：E4：A5：44：35：69 to access Internet from Monday to Friday.
11N Wireless Broadband Router User Guide 8.3 URL Filter Settings You can use URL fil tering to forbi d t heir access to certain websites at a specified time. ¾ Filter Mode: You can select either “Permit only” or “Forbid only”. ¾ Access Poli cy: Select one number from the drop-down list. ¾ Remark: A simple description of the configured file. You can also leave it blank. ¾ Start/End IP: Enter the start/end IP address.
11N Wireless Broadband Router User Guide ¾ Time: Select the time range of URL filter. ¾ Date: Select the day(s) to run the access policy. ¾ Enable: To enable/disable the access policy (forbid /permit the packets matched with the access policy to pass through the router). Example1 Forbid all co mputers on LAN to acce ss baidu.com during 8:00 to 18:00 from Monday to Friday. Example2 P ermit LAN computers wi th the IP addresses of 192. 168.0.100-192.168.0.115 to acc ess yahoo.com.
11N Wireless Broadband Router User Guide NOTE: Enter only one domain name for each access policy for one access policy can only filter one domain name. So, if you want to filter multiple domain names, you need to set multiple access policies 8.4 Remote Web Management This secti on i nstructs how to al low the network administrator to manage the R outer r emotely. If y ou want to acc ess the R outer from outs ide of the network, please click the checkbox after “Enable”.
11N Wireless Broadband Router User Guide ¾ Enable: Check to enabl e remote web management. ¾ Port: The management port open to outside access. The default value is 80. ¾ IP Address: Specify the range of the IP addresses of the computers on the Internet for remote management. NOTE: 1. If you want to l og in the devi ce’s Web-based Utility via port 8080, you need to use the format of WAN IP address: port (for exampl e http ： //220.135.211.56:8080) to implement remote login. 2.
11N Wireless Broadband Router User Guide Router to implement remote web management. For example: If you want to configure the computer at the IP address of 218.88.93.33 to access the router’s web-based utility via port 8080, please set the parameters as above.
11N Wireless Broadband Router User Guide Chapter 9 Routing Settings 9.1 Routing Table This page shows the router’s core routing table. The main duty for a router is to look for a best path for every data p acket, and tr ansfer thi s data packet to a destination station. In order to fulfill this function, many transferring paths, i. e. routi ng tabl e, are saved in the router, for choosing when needed. 9.2 Static Routing This screen is used to set the router’s static routing.
11N Wireless Broadband Router User Guide Destination network IP address : T he destination host or IP segment you visit. Subnet mask: Enter the subnet mask, generally it is 255.255.255.0 Gateway: The entry IP address of the next router. NOTE: 1. The gateway must be at the same net segment with the router’s LAN IP. 2. If the des tination IP addres s i s one host ’ address, then the subnet mask must be 255.255.255.255. 3.
11N Wireless Broadband Router User Guide Chapter 10 System Tools 10.1 Time Settings This secti on is to confi gure the router ’s system ti me. You can set it manually or obtain the GMT time from the Internet. ¾ Time zone: Select the time zone where you are operating the Router from the drop-down list. ¾ Customized time: Enter the ti me you wi sh to configure. NOTE: When the Router is powered off, the time setti ngs will be l ost.
11N Wireless Broadband Router User Guide Internet. Only when you connect to the Internet and obtai n the GMT ti me or set the time on thi s screen, can the ti me set tings in othe r funct ions (e.g. security settings) take effect. 10.2 DDNS The DDNS (Dynam ic Domain N ame S ystem) is supported in this Router. It is used to assign a fixed host and domai n name to a dynami c Internet IP addr ess.
11N Wireless Broadband Router User Guide ¾ Main features: 1. Mostly, your ISP provides a dynamic IP address and the DDNS is used to capture the changeable IP address and match to thefixed domain. Then users can ha ve acc ess to the In ternet to c ommunicate with others outside the network. 2. DDNS can help you to establish a virtual host in your home or company. ¾ DDNS: Click the radio button to enabl e or disable the DDNS service.
11N Wireless Broadband Router User Guide account i nformation in DDNS serv er, y ou can then access the web page by entering http://tenda.3322.org in the address field. 10.3 Backup/Restore On thi s screen, you can back up the router’s curr ent settings or restore previous settings. ¾ Backup Setting: Click the Backup button to back up the Router’s settings and select a path to save them.
11N Wireless Broadband Router User Guide Click the “Save” button to save the c onfiguration files.
11N Wireless Broadband Router User Guide ¾ Restore Setting: Click the “ Browse” button to sel ect the backup files. Click the “ Restore” button to restore previ settings.
11N Wireless Broadband Router User Guide 76
11N Wireless Broadband Router User Guide 10.4 Restore to Factory Default This screen allows you t o restore al l setti ngs to the factory default values. ¾ Restore: Click thi s butto n to restore to defaul t settings. ¾ Factory default settings: Password: admin IP address: 192.168.0.1 Subnet mask: 255.255.255.0 NOTE: After restoring to defaul t setti ngs, please restar t the router to make the default settings effective. 10.
11N Wireless Broadband Router User Guide upgrade file from our website, www.tenda.cn. ¾ Browse: Click thi s button to sel ect t he upgr ade file. ¾ Upgrade: Click this button to start the upgr ading process. After the upgrade is completed, the router will reboot automatically. 10.6 Reboot the Router Reboot the router to mak e the conf iguration effective. The router will cut its WAN connec tion automat ically after rebooting.
11N Wireless Broadband Router User Guide Reboot the r outer: Click th is butto n to reboot the router. 10.7 Password Change This section is to set a new password to better secu re your router and network. ¾ Old password: Enter the old password. ¾ New password: Enter a new password.
11N Wireless Broadband Router User Guide ¾ Confirm new password: Re-enter to confirm the new password. NOTE: To secure the router and your network, it is highly recommended t hat y ou c hange t he in itial password.
11N Wireless Broadband Router User Guide 10.8 Syslog The secti on is to vi ew th e system l og. You can view various cond itions appearing after system start, an d also check whether there’ s an attack on the network. The log can record at most 150 entries. ¾ Refresh: Click this button to update the log. ¾ Clear: Click this button to clear the current shown log.
11N Wireless Broadband Router User Guide 10.9 Log out After all settings are finished, please click’” Log out” to exit securely and completely.
11N Wireless Broadband Router User Guide Appendix 1 Glossary Channel: An instance of medium use for the pu rpose of pa ssing protocol data uni ts (P DUs) that may be used simultaneously, in the same volume of space, with other instances of medium use(on other channel s) by ot her instances of the same ph ysical layer (PHY),wi th an acceptably l ow fr ame error r atio(FER) due to mutua l interference.
11N Wireless Broadband Router User Guide the network.WP A2 i s the second gen eration of WP A security and provides a stronger encryption mechanism through Advanced Encryption Standard (AES), which is a requirement for some government users. 802,1x authentication Static W EP k ey is d ifficult t o ma nage fo r wh en y ou change the key, you will have to inform all others, and if the key is disclosed in one of the places, the key can no longer provide security.
11N Wireless Broadband Router User Guide Appendix 2 Product Features z Supports IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3 and IEEE 802.3u standards. z 5dBi hi gh gai n omn i-directional ant enna, wi th strong signals and long transmission distance.
11N Wireless Broadband Router User Guide z Supports WDS to extend wireless network z Supports virtual server, DMZ host z Provides syslog to record the running status of the router Appendix 3 FAQ This s ection provides s ome s olutions t o t he p roblems which ma y occur duri ng the router ’s i nstallation or usage. The i nstructions below may help you deal with the problems. If your problem is not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.
11N Wireless Broadband Router User Guide the R outer’s LA N IP addres s 192. 168.0.1 (op en “Command Prompt ” and type “Pi ng 19 2.168.0.1” a nd then enter). If it is OK, please make sure your browser does not access the Internet by proxy server. If the ping fails, you can press the “RESET” button for 7 seconds to restore to defaul t setti ngs. And then repeat th e pi ng operation. If it still does not work, please contact us. 2. Forgot the login password and cannot enter the Web-based Utility.
11N Wireless Broadband Router User Guide 1450 or 1400. 5.How to share my c omputer’s resource w ith other users in Internet？ If you want Internet users to access the internal server via the router such as: e-mail server, Web, FTP. You can configure the “Virtual Server”. Step 1: create your internal server, make sure the LAN users can access these servers and know related service port. For example, Web server’s port i s 80; F TP is 21; SMTP is 25 and POP3 is 110.
11N Wireless Broadband Router User Guide WEB Server TCP 80 FTP Server TCP 21 Telnet T CP 23 NetMeeting T CP 1503、1720 File MSN Messenger TCP/UDP Send:6891-6900(TCP) Voice:1863、6901(TCP) Voice:1863、5190(UDP) PPTP VPN TCP 1723 Iphone5.
11N Wireless Broadband Router User Guide Appendix 4 Clear Wireless Configuration Clear Wirel ess configuration file under windo ws XP 1. Right click “My Network Places” on your computer desktop and select “Properties”. 2. Ri ght cli ck “W ireless Network Co nnections” a nd select “Properties”.
11N Wireless Broadband Router User Guide 3. Click “Wireless Network Configuration” and clear the corresponding wi reless configuration fil e as sh own below. Clear Wireless configuration file under windows 7 1. Right click “Network” and click “Properties”.
11N Wireless Broadband Router User Guide 2. Click “Manage wireless networks” on the l eft side of the window. 3. De lete t he c orresponding c onfigured file “Manage wireless networks”.
11N Wireless Broadband Router User Guide 93
11N Wireless Broadband Router User Guide Appendix 5 Regulatory Information EU Declaration or Declaration of Conformity Hereby, SH ENZHEN T ENDA T ECHNOLOGY C O.,LTD, declares t hat t his W ireless Br oadband R outer is in compliance with t he e ssential r equirements a nd o ther relevant provisions of Directive 1999/5/EC. FCC Statement This equi pment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to part 15 of th e FCC rul es.
11N Wireless Broadband Router User Guide -Connect the equi pment into an outlet on a ci rcuit different from that to which the receiver is connected. -Consult the deal er or an experi enced radio/TV technician for help. To assure c ontinued compl iance, a ny changes or modifications not expres sly approved by the party responsible for compli ance coul d void the us er’s authority to operate this equipment.
