Operation Instructions

TWS ANC 主动降噪真无线蓝牙耳机 U2032
规格参数
蓝牙版本：
5.1
充电时间：约
1
小时
信号距离：
10
米
通话时间：约
4-6
小时
播放时间：约
4-5
小时
待机时间：约
60
小时
电池规格：耳机
3.7V,40mAh;
充电仓
320mAh
支持格式：
A2DP1.3
、
AVRCP1.6
、
HSP1.2
、
HFP1.7
功能操作说明
1、开机
将耳机从充电仓拿出自动开机，长按左右耳机多功能键 2 秒切换降噪功能和通透模式。
2
、关机
将耳机放入充电仓自动关机或蓝牙断开十分钟后自动关机，及取出耳机后不连接蓝牙时十分
钟后自动关机。
3
、开机回连
当配对成功后，第二次开机时蓝牙耳机优先进入回连状态，自动回连已连接过的手机。
4、播放/暂停
在待机状态下，单击左右耳机多功能键均可直接播放音乐，播放时单击左右耳机多功能键均
可暂停播放。
5、切换歌曲
播放音乐时双击左右耳机多功能键切换到下一曲，三击左右耳机多功能键切换到上一曲。
6
、来电接听
手机来电时，单击左右耳机多功能键均可接听电话。
7、来电挂断
手机通话时，单击左右耳机多功能键均可挂断电话。
8、来电拒接
手机来电时，双击左右耳机多功能键均可拒接来电。
9
、低电量提示
当蓝牙耳机电池电量不足时会有提示音，请勿继续使用并充电。
配对方式
1、从充电仓取出直至红蓝灯交替闪烁，进入对耳搜索配对状态，进入对耳自动配对，配对成
功后左右耳持续红蓝灯交替闪烁，同时播放对耳配对成功提示音。
2、启动手机或者其他设备的蓝牙功能，如果是安卓系统手机或者设备，请点击“搜索蓝牙设
备”选项，如果是 IOS 系统手机或者设备则会自动搜索设备；当搜寻到该蓝牙耳机的信号后，
点击进入配对；当配对成功后，耳机会发出连接成功的提示音，左右耳机提示灯熄灭，进入
连接待机状态。
充电操作
尽量避免在有腐蚀的环境中使用本耳机，以免对耳机的功能产生影响。
1、将 Micro USB 充电线一头插上充电器即可；充电时，充电仓数码管数字显示随着电量的高
而逐渐加大，充满后数码管显示数字为 100。
2、耳机充电：将耳机放入充电仓中即可自动充电，充电时耳机指示灯为红色，充满电后熄灭；
耳机放入充电仓时，当放入左耳时充电仓数码管数字显示“L”，当放入右耳时充电数码管数
字显示“R”。给耳机充电过程中充电仓的电量会随之下降，数码管数字显示也随着电量的下
降而逐渐变小，当耳机充满电后充电仓的数码管显示会常亮。
注意事项
1、请在安全的环境下充电。在给充电仓充电时，当充电指示灯指示满电后请尽快将充电仓与
USB 充电线分开，以免在长时间插着充电对充电仓造成损伤。
2、在音乐播放时，请将音乐调至合适音量大小，以免长期在大音量状态下对听力造成损伤。
3、尽量避免在有干扰源的地方使用本耳机，否则有可能对耳机信号产生影响。
4、尽量避免在有腐蚀的环境中使用本耳机，以免对耳机的功能产生影响。
温馨提示：在您使用本蓝牙耳机听音乐或者通话时，请注意适当调节音量大小，以免过大的
音量对您的听力造成影响！
Specifications
Functional Operation Instructions
Turn on
Take the headset out of the charging cabin it will turn on automatically. Long-press the left or right headset multifunctional keys
for 2 seconds to switch between ANC (active noise cancelling) and transparency mode.
Turn off
Put the earphone into the charging cabin it will automatically turn off or automatically power off after Bluetooth disconnection 10
minutes and without connecting Bluetooth 10 minutes after taking the headset out of the charging cabin.
Turn on reconnection
When the pairing is successful, the Bluetooth headset will first enter the reconnection state when it is turned on for the second time,
and automatically reconnect the connected mobile phone.
Play / Pause
In standby mode, click the left or right earphone multifunctional key to play music directly, and click left or right earphone
multifunctional key to pause playback.
Switch songs
When playing music,double-click the headset multifunctional keys will switch to the next song, and triple-click the headset
multifunctional keys will switch to the previous song.
Calling answer
When the phone calls, click the left or right headset multifunctional key to answer the call.
Calling hang up
When the phone is talking, click the left or right headset multifunctional key to hang up the phone.
Call rejection
When the phone calls, double click the left or right headset multifunctional key to reject the call.
Low battery remind
When the battery of the Bluetooth headset is low,there will be reminding voice,please stop to use and charge .
Pairing Method
1.Take it out of the charging cabin until the red and blue lights flash alternately, enter the pairing state of the headset search, and
enter the automatic pairing. The red and blue light of headsets flash alternately continuously, and at the same time reminding
successful for pairing.
2.Start the Bluetooth function of the mobile phone or other devices. If it is an Android mobile phone or device, please click the
"Search Bluetooth device"option. If it is an IOS mobile phone or device, it will automatically search for the device. Click to enter
pairing after see the Bluetooth signal. When the pairing is successful, there will be reminding tone, then the left and right headset
reminding lights light off, and enter the connected standby state.
Charging Operation
Please do not use the headsets in a corrosive environment, prevent affect the function of the headsets.
1.Plug the Micro USB charging cable into the charger.When charging, the digital display of the charging cabin's digital tube
gradually increases with the increase of power. When full, the digital tube shows the number is 100.
2.Headset charging: Put the headset into the charging cabin to automatically charge. The headset indicator is red when charging,
and it will light off when fully charged. When put headsets into the charging cabin, if put in the left headset, the digital tube
displays “L”. If put in the right headset, the digital tube display “R”. The power of the charging cabin will decrease during the
charging of the headsets, and the digital display of the digital tube will gradually change as the power drops. When the headsets
are fully charged,the digital tube display will stop flashing and just light on.
TWS ANC Bluetooth Earphone U2032
Note content
1.Please charge in a safe environment. When charging the charging cabin, when the charging indicator indicates full power,
please separate the charging cabin from the USB charging cable as soon as possible to avoid damage to the charging cabin when
plugged in for a long time.
2.When playing music, please adjust the music to a suitable volume to avoid hearing damage at high volume for a long time.
3.Try to avoid using this headset where there is a source of interference otherwise it may affect the headset signal.
4.Please do not use the headset in a corrosive environment prevent affect the function of headsets.
Tips: When you use this Bluetooth headset to listen to music or calling, please pay attention to adjust the volume properly to avoid
excessive volume affecting your hearing.
Bluetooth version：Bluetooth 5.1
Charging time: About 1hour
Signal distance: 10m
Call time: About 4-6hours
Play time: About4-5 hours
Standby time: About 60hours
Support mode:A2DP1.3,AVRCP1.6, HSP1.2,HFP1.7
Battery: Earphone 3.7V,40mAh; charging cabin 320mAh