Specifications
Table Of Contents
- 1
- Applying development of unilateral communication
- Serial port intercommunication agreement
- Summarize
- Control command format of serial
- Set BaudRate
- Get Reader Version
- Set Relay
- Get Relay
- Set Output Power
- Set Frequency
- Read Param
- Set Param
- Read Auto Param
- Set Auto Param
- Select Antenna
- Restore factory settings
- Reboot
- Start/ stop automode
- Clear Memory
- Set Reader Time
- Get Reader Time
- Set Report Filter
- Get Report Filter
- Set Reader Network Address
- Get Reader Network Address
- SetReader MAC
- Get Reader MAC
- Report Now
- Get Tag Info.
- GetReaderID
- Command format of serial read-write tag
- Collection of operation command
- Electronic tag storage area and notes
- SDK software development
- SDK compose
- Design introduction
- Basic constant and figure
- Constant definition
- API function return code
- Data type definition
- Parameter figure in reader
- Function return code
- Control command function
- Connect reader
- Disconnection
- Set baud rate
- Read version
- Set output power
- Set operation frequency
- Read reader basic operation parameter
- Set reader basic operation parameter
- Read reader auto parameter
- Set reader auto parameter
- Select antenna
- Set relay state in reader
- Reboot reader
- Set time
- Get time
- Get record
- Delete all records
- Network command
- Set IP address for reader
- Get IP address in reader
- Set reader MAC address
- Get reader MAC address
- Read write ISO18000-6B function
- Identify tag ID number
- Identify selected tag ID number
- Read data block
- Write data block
- Slow write data block
- Set write protection
- Read write protection
- Read write ISO18000-6C function
- Identify EPC number of ISO18000-6C tag
- Read a block data
- Write a block data
- Set read write protection state
- FCC警告语大于20cm(1)
Content | VI-88TR development handbook
CONTENT
1 Applying development of unilateral communication ........................ 5
1.1 Applying development of unilateral communication ...................... 5
1.2 Wiegand interface agreement ......................................................... 5
1.2.1 Wiegand26 format .................................................................. 6
1.2.2 Wiegand34 format .................................................................. 6
1.3 RS485 interface agreement ............................................................ 6
2 Serial port intercommunication agreement ..................................... 8
2.1 Summarize ....................................................................................... 8
2.1.1 Command packet format without address ............................ 8
2.1.2 Command packet format with address .................................. 9
2.1.3 Return packet format without address .................................. 9
2.1.4 Return packet format with address ..................................... 10
2.1.5 Error code ............................................................................. 10
2.1.6 For example .......................................................................... 11
2.1.7 Checksum ............................................................................. 11
2.2 Control command format of serial ................................................ 12
2.2.1 Set BaudRate ....................................................................... 12
2.2.2 Get Reader Version .............................................................. 13
2.2.3 Set Relay .............................................................................. 15
2.2.4 Get Relay .............................................................................. 16
2.2.5 Set Output Power ................................................................. 17
2.2.6 Set Frequency ...................................................................... 18
2.2.7 Read Param .......................................................................... 20
2.2.8 Set Param ............................................................................. 21
2.2.9 Read Auto Param ................................................................. 23
2.2.10 Set Auto Param .................................................................... 23
2.2.11 Select Antenna ..................................................................... 25
2.2.12 Restore factory settings ...................................................... 26
2.2.13 Reboot .................................................................................. 27
2.2.14 Start/ stop automode ............................................................ 28
2.2.15 Clear Memory ....................................................................... 28
2.2.16 Set Reader Time ................................................................... 29
2.2.17 Get Reader Time .................................................................. 29
2.2.18 Set Report Filter ................................................................... 30
2.2.19 Get Report Filter .................................................................. 31
2.2.20 Set Reader Network Address ............................................... 32
2.2.21 Get Reader Network Address .............................................. 32
2.2.22 SetReader MAC .................................................................... 33
2.2.23 Get Reader MAC ................................................................... 33
2.2.24 Report Now ........................................................................... 33
2.2.25 Get Tag Info. ......................................................................... 34
090909RevA|Page 2 of 97