User's Manual

ManualsBrandsShenzhen Weijian Plastics ManualsComputers & AccessoriesWireless Keyboard

USER’S GUIDE

TO W2028RF WIRELESS

KEYBOARD AND MOUSE

Please read the followings before using the set.

Introductions:

This keyboard/mouse set is a wireless input device

with 27 Mhz radio frequency. It is plug & play with

Windows Me/2000/XP, no need of any software

installation. When user typing the keyboard,

membrane will detect the user typing character, then

send signal to the MCU; through the 27M Hz RF

circuit transmit the modulation signal, the MCU will

enclose the signal and modulation the signal that uses

FSK modulation type. Please remove the software for

your previous keyboard or mouse that you have

installed before using this new device.

This set consists of 3 parts: keyboard, mouse, and

receiver.

Note:

his device complies with Part 15 of the FCC rules. Operation is

subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesired operation.

Caution:

The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications to this equipment. Such

modifications could void the user authority to operate the equipment.

Summary of content (9 pages)

PAGE 1
Note: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user authority to operate the equipment.
PAGE 2
(Figure 1)
PAGE 3
System Requirement IBM PC compatibles PS/2 ports for mouse and for keyboard Microsoft Windows Me/2000 and XP Install Batteries: The wireless mouse and the keyboard need two AAA batteries individually. (For best performance, please use only alkaline batteries) 1. Open the battery compartment covers of the mouse and the keyboard. 2. Insert two AAA batteries inside the compartment individually. 3. Close the battery compartment covers.
PAGE 4
Caution: When you do not use the wireless keyboard/mouse for a long period of time, please remove the batteries. Connect The Receiver RF wireless keyboard/mouse uses digital radio technology to communicate. It transmits radio frequency signals which are picked by the receiver, then pass on to the computer. The receiver is connected to the computer’s PS/2 ports Via a Y cable. Connect the green connector to the computer’s mouse port, and plug the purple connector the keyboard port.
PAGE 5
(see figure 2): Press the ID Buttons, the ID code will be set automatically. The process must be completed within 20 seconds. After setting the ID code, the Receiver’s RF LED blinks. This means the keyboard and the mouse communicate with receiver successfully. If the LED does not blink, or the keyboard/mouse does not work properly. Please re-install the batteries or reset the ID Code.
PAGE 6
well with Windows Me/2000/XP, no need of any software driver. The keyboard is a 104/5-key model with 15 hot keys that can take you directly to your favorite multimedia activities. And you can navigate music and video clips, surf the web and start programs. All the hot keys are on the upside of the keyboard. The functions are （See Figure3 ） 1.My Favorite: Open my favorites 2.Web Search: Launch your web search function 3.Web Refresh : Update and refresh the web page. 4.E-mail: Call the email application 5.
PAGE 7
PAGE 8
Trouble-shooting 1.If your keyboard/mouse does not work after installation, please check the followings: Make sure you have connected the receiver correctly with the computer and the receiver’s connectors have been properly plugged into computer’s PS/2 ports. Make sure you have inserted the batteries correctly.
PAGE 9
keyboard/mouse on this computer. 3．If the mouse cursor does not move properly, or the key-in data does not prompt up on the screen, please check following: a). Clean the ball and the roller of the mouse b). Check the position of your receiver. Maybe the receiver is too far away. c). Check the large metal devices, such as microwave, electric stove, television, hair dryer… , which may interfere the receiver’s radio reception. d). Check the status of the batteries. The batteries may be near dead.