USER MANUAL Model:V6 PLUS_T20S Bluetooth Headset Manufacturer:Shenzhen Winnerelec Industrial Co.
Table of Contents Introduction ---------------------------------------------- Page 1 Packet Contents ----------------------------------------Page 2 Install Instructions ---------------------------------------Page 3 Charging ---------------------------------------------------Page 5 General Operation Instructions -----------------------Page 5 FM Operation ---------------------------------------------Page 7 Universal Pairing and Using ----------------------------Page 8 Bluetooth Intercom Talk -----------------
1: Introduction Thank you for choosing the T20s Motorcycle 6 Riders full-duplex stereo Bluetooth wireless helmet headsets, designed for installing into most open-face, flip-front and full-face style helmets. With the T20s, you can call hands-free on your Bluetooth mobile phone, listen to music or voice instructions of GPS navigation, and activate wireless intercom for rider to rider or rider to passenger intercom talk within range of 1200 meters(depending on terrain conditions).
2: Packet Content HIFI Speaker and Microphone 2
Clip Mounting Bracket User Manual 3: Fixed installation method 1:Locate the helmet at the left and clean it up 2:Peel off the 3M rubber protective film 3:Apply pressure to the metal carrier to secure the holder firmly Note: it takes 24 hours after drying.
Install host 1:Slide V6S PLUS_T20S host off the top of the clip and you'll hear a click when it is completely plugged in 2:Plug in the 3.
4: Charging 1. You can charge with the Micro USB cable in the package. During charging, OLED show “Charging”. After full charging, OLED show “Charged full”, and it is recommended to recharge the battery before each use. Suggest full charge before each use. 2. Low battery warning:Headset will automatically voice prompt low battery at every 5 minutes to prompt the user to recharge it. 3. Battery state notify: When standby, double press Power button to report battery level.
Mobile Phone/GPS pairing steps 1. When power off,press Power button for approx 8S, the screen display “Pairing”,Open the phone Bluetooth, search for “ V6S PLUS_T20S ”,then click on the phone connection pair.After the pairing, the screen display “Paired” and goes back to standby mode. Answer phone calling: The unit will automatically answer the incoming call after 12 seconds. Or press Phone button to answer the incoming phone call immediately.
connecting again. Connect third party calls: When connecting two cell phones, during phone call with first cell phone and second cell phone dial in, can double press Phone two times to answer the second cell phone and hold the first cell phone conversation. When finish the second cell phone conversation, will back to the conversation with fist cell phone. Music Control: Press the Phone button to play and pause the music.
Preset and store up to 6 FM radio stations In FM radio mode, when a favorite station is found, long press Phone button 1 seconds to save, a beep tone will sound. Preset and store up 6 FM radio stations. Once 6 stations have been saved, saving a new station will overwrite the oldest saved station. Press Phone button to rotate between each saved station.
8: Bluetooth Intercom Talk The V6 PLUS_T20S can be paired with other T20s for up to a total of 6 units for full duplex Bluetooth intercom. Pairing Two headsets and talk Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Pairing Five headsets and talk Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
after paring finish, the screen display “Paired” and go back to standby mode. Step 5: After pair finished, Short press Unit 1’s Button B on either unit1 and unit2, it will start intercom, and screen display “Intercom B”. During Intercom talking, short press Phone button to exit intercom mode. Step 6:After pair finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press Phone button to exit intercom mode.
Step 1: Power on unit 1 and unit 2, then long press unit 1 and unit 2 Button B, the screen display “Pairing” of all, then short press Button B on either unit, then the unit’s screen display “Searching”, after paring finish, the screen display “Paired” and go back to standby mode.
Step 7:After pair finished, Short press Unit 1’s Button C on either unit1 and unit3, it will start intercom, and screen display “Intercom C”. During Intercom talking, short press Phone button to exit intercom mode. Step 8:After pair finished, Short press Unit 1’s Button D on either unit1 and unit4, it will start intercom, and screen display “Intercom D”. During Intercom talking, short press Phone button to exit intercom mode.
9: Technical specifications: 1. Bluetooth 3.0 Support : HSP,HFP,A2DP,AVRCP, AGHSP 2. Working hours: 12 hours 3. Standby time: 300 hours 4. Charging time: 3 hours 5. Battery: lithium containing rechargeable lithium battery 650mAH, 3.7v 6. Dimensions: 87cm * 45cm * 26cm 7. Weight: 50g 8. Certification :CE, FCC, TELEC NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
MADE IN CHINA Web: www.winnerelec.com E-mail: sales@winnerelec.