PIR-SD User’s Manual PIR Motion Sensor with Hidden Color Camera, SD Recorder, and Remote Control
© Copyright 2012 This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
Warranty SecurityMan warrants that this product will be free from defects in title, materials and manufacturing workmanship for one year from the date of the purchase or otherwise specified on the package. If the product is found to be defective then, as your sole remedy and as the manufacturer’s only obligation, SecurityMan will repair or replace the product. This warranty is exclusive and is limited to this product.
Table of Contents Introduction Features Important Operating Restrictions Conditions Safety Instructions Package Contents Product Basics PIR-SD Remote Control Set Up Set the Date and Time Adding and Cancelling Remote Control Adding Remote Control Cancelling Remote Control Operation Using PIR-SD Motion Detection Recording Emergency Recording Stop Recording New File Alert SD Full Alert (Memory Full) Playback Recorded Video Integrating with Air-Alarm Series Adding PIR-SD Remote to the Alarm Host Cancelling PI
Introduction Thank you for purchasing SecurityMan PIR-SD. The PIR-SD is a color camera with SD recorder hidden inside a PIR motion detector. This covert motion detector camera blends perfectly into almost any home or business environment where an alarm system might be present and can also be intergraded with any of our SecurityMan DIY Wireless Home Alarm Systems, providing you with both security and discreet monitoring capabilities.
Important This guide provides important information on the use and operation of your PIR-SD. Please read all the information carefully prior to using the product for the best performance and to prevent any damage/injuries or misuse of the device(s). Customers are entitled to have read through this complete user’s manual before using the PIR-SD. Any unapproved changes or modifications will void your warranty. Please ensure to have a complete understanding of the following restrictions.
• DO NOT place this product near any medical equipments. Radio waves might potentially cause breakdown of electrical medical equipment. This product should be placed at least one foot away from any heart pacemaker. Radio waves might potentially influence heart pacemaker and lead to respiratory disturbance. • DO NOT use this product to violate one’s privacy. Monitoring one’s private activities without consent is illegal and this product is not designed and manufactured for these purposes.
• DO NOT put the camera in quaky paces. The camera may be unstable or out of operation if installed improperly. Such installation may also cause breakdown. • DO NOT use the camera in complex environment, the obstruction of stumbling block will affect the electromagnetic wave and influence the receiving range. Wall, tree and other stumbling block might absorb, reflect the electromagnetic wave, and influence the receiving range. • DO NOT use the camera in the places which are covered with metal.
Conditions Please read the following messages to make sure your working environment is suitable. • The temperature should be kept between –10˚C and 50˚C (14˚F to 122˚F). The relative humidity should be kept between 20% and 80%. • Avoid putting the product in places where temperature or humidity may change rapidly. • Keep it dry, dustless and avoid exposure directly in sunlight. • Keep product away from heat sources such as electric heater.
Package Contents **SD card not included.
Product Basics PIR-SD Front Back Mini USB Power Socket Mounting Base Detecting LED Camera Remote Control Stop Record Stop Record button Stop/Deactivate Motion Detection and Emergency Recording Study Button Power/USB SD Slot Study Sensor Window Motion Record Emergency Record Motion Record button Start/Activate Motion Detection Recording Emergency Record button Start Emergency Record (1 minute clip) 7
Set Up Set the Date and Time Insert an SD card (note included) “face up” into the SD slot located on the right hand side of the PIR-SD as illustrated below. SD IMPORTANT NOTICE: The PIR-SD required an SD card to be inserted into the SD slot in order for the PIR-SD to function as a motion detector/recorder. Connect the PIR-SD to your PC or Laptop using the USB cable provided as illustrated below.
Once connected, an “Auto Play” pop up window will appear (as shown below) providing various programs for you to use to access and view the stored files. Click on the “Open Folder to View Files” option to open a folder view as illustrated. Double-click on the “GetSysTime” folder, double-click on the “GetSysTime.exe” file located on the SD card, and then click on the “Get System Time” pop up to synchronize your computers time to the PIR-SD. Make sure the computer you are using has the current time and date.
After clicking on the “Get System Time” pop up, a confirmation pop up will appear letting you know that the time and date were set successfully. Click OK to close the window and disconnect the PIR-SD from your computer. NOTE: A “SysTime.bin” file will be created indicating that the date and time was set correctly. Mount the PIR-SD’s mouting bracket in the desired location and secure it to the wall using the screws provided (use the green dry wall inserts when applicable) as shown below.
IMPORTANT NOTICE: Due to a 2~3-sec delay time to record, we recommend to mount the PIR-SD about 15ft from the intended monitoring object for proper recording. Slide the PIR-SD over the mounting bracket and push it downward to secure. Adjust the PIR-SD as necessary until you reach a desired viewing angle as shown below. Wall Finally, connect the PIR-SD to the USB power adapter and a solid red light will appear in the motion detection window for 30 seconds as illustrated below.
Adding and Cancelling Remote Control Adding Remote Control: 1) While plugged into the power outlet, press and release the “Study” button located on the back of the PIR-SD. The PIR-SD will beep once after being pressed indicating that it is in study mode. 2) Press any one of the four buttons on the remote control 2 consecutive times and the PIR-SD will beep 5 times to indicate the remote control has been successfully added to the PIR-SD.
NOTE: Since the same command are used to cancel the remote control from the PIR-SD and disable the video recording from the Alarm Host (when integrating), it is important to remember to enable the video recording back (or pair video recording) to the Alarm Host whenever cancelling the remote control from the PIR-SD.
Stop Recording To stop emergency recording or Deactivate Motion Detection recording, simply press the “Stop Record” button on the remote control at any time (the PIR-SD will beep twice to indicate that recording has been stopped). Stop Record New File Alert After deactivating motion detection or emergency recording, by default the “New File Alert” featured: • Blue LED will stay solid for 5 seconds. • PIR-SD will beep 5 times. To disable the PIR-SD from beeping 5 times. Make sure the PIRSD is disarmed.
The SD Full notification flashes whenever there are 1 minute or 60MB of the free capacity left for system buffering. The PIR-SD system does not have an overwrite feature. Playback Recorded Video You can playback recorded files directly from the PIR-SD (when connected to a PC) or directly from the SD card by inserting the card into your computers card reader. To playback recorded video on a PC: 1.
video recording (on/off) as shown below. To avoid using multiple remote controls when integrating the PIR-SD to the Air-Alarm host series, please add the PIR-SD remote control to the Air-Alarm host series or vice versa. Adding PIR-SD Remote to the Alarm Host Step 1: Press PRGM/SET + Password (system default 888)+ENT+70+ /Learn” light will appear solid blue/red]. ENT+00+ENT [the “ Step2: Press any 1 of the 4 buttons on the PIR-SD remote twice consecutively to add.
(up to 4 sensors) sensor that was paired to that zone.] (The “ /Learn” light will appear solid blue/red) The alarm host will beep twice, and the “ /Learn” light will flash once to indicate the PIR-SD motion detection is successfully cancelled from the Alarm Host. Enabling Video Recording To enable video recording, please follow steps 1 and 2 below.
Disabling Video Recording Make sure the host is “DIS-ARMED” and press: Press and hold down the “Study” button on the back of the PIR-SD for 5 seconds, then release, and the PIR-SD will beep for 3 seconds to indicate video recording is successfully disabled. NOTE: Since the same command are use to remove the remote control from the PIR-SD and disable the video recording from the Alarm Host, please pair the remote control back to the PIR-SD whenever disabling video recording from the Alarm Host.
Specifications Image Sensor 1/6.5”CMOS color Resolution 640x480 Recording Speed 30fps Camera Lens 8mm Camera Viewing Angle H: 60 degree, V: 35 degree Recording Video Format AVI Recording Time and Size One minute per motion detection event. 40MB/minute. 32GB = 12hrs of video LED Indicator PIR sensor/ camera Remote Control Wireless (General) 2 LED lights (Red: power, record, alarm/ Blue: SD full or new REC file) USB Port 2.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.