User's Manual Part 2

These instructions do not apply to all vehicles. They are meant as only
as a general guide due to the number of different makes & models. For
vehicle specific questions, contact your vehicleʼs manufacturer.
Monitor Installation
When choosing a location to mount the monitor, make sure the monitor is in an area that will
not obstruct your vision while driving. It can be placed on the dashboard, or on the windshield
depending on the angle.
1. Temporarily place the moni-
tor stand in the location that
you have chosen. Make sure
the driverʼs vision is not ob-
structed in any way or any of
the vehicleʼs
2. Route the monitorʼs power
cable to the vehicleʼs fuse
block/box or cigarette lighter
socket/12V power outlet de-
pending on the cable you are
using
3. If you are satisfied with the
location of the monitor and
the cable route you have
chosen, attach the monitor or
stand with the supplied Velcro.
MONITOR POWER CONNECTION
There are two ways to supply the monitor with power, one uses a 12 Volt cigarette lighter
adaptor plugged into the vehicleʼs cigarette lighter socket, and the other uses a wiring
harness hard wired to the vehicleʼs fuse box.
12 Volt Cigarette Lighter Adaptor Using the Monitorʼs ON/OFF Button
1. Choose a route for the cable from the monitor to the cigarette lighter socket. It can be a direct
route with the wire exposed or a route around the dashboard hidden under the vehicleʼs inte-
rior trim. When using a direct route for the power cable make sure the power cable is secured
and will not interfere with the operation of the vehicle. When routing the power cable behind
the vehicleʼs interior trim be careful not to cut the wire on and sharp edges or pinch and dam-
age the cable when re-installing the trim.
2. Plug the end of the power cable into the monitor,
3. Plug the 12 Volt cigarette lighter adaptor into the cigarette lighter socket.
4. Press the ON/OFF button to turn the monitor.
Hard Wired to Fuse Box Using the Monitorʼs ON/OFF Switch (Fig. 1)
1. Remove the negative battery cable from the vehicleʼs negative battery terminal.
2. Remove the fuses from both of the in-line fuse holders.
3. Connect the Red wire to the 12 Volt +/ACC terminal in the vehicleʼs fuse box. See vehicleʼs
ownerʼs manual for fuse box diagram.
4. For the ground cable locate an area of metal on the vehicleʼs body/firewall that does not have
any vehicle components behind it. Sand off any paint to reveal bare metal, this area will be
your chassis ground.
5. Drill a hole for the supplied self tapping sheet metal screw. Make sure there are not any ve-
hicle components on the other side of where you are drilling the hole.
6. Attach the grounding cable to the chassis ground with the self-tapping sheet metal screw.
7. Plug the power cord into the monitor.
8. Press the ON/OFF button to turn the monitor.
Automotive video equipment installations can be difficult at times, even to the most expe-
rienced of installation technicians. If you are not confident working with electrical wiring,
removing and reinstalling interior panels, carpeting, dashboards or other components of your
vehicle, please call our Toll-Free Help Line 1-800-445-1797 and our in-house technical ser-
vice team will answer your installation questions.
If you have vehicle specific questions, contact the vehicleʼs manufacturer, or consider having
the VRBCS300W professionally installed.
VRBCS300W
Back-Up Camera
and Monitor
Before You Install
Parts
Installation Installation
1 - Back Up Camera
1- TFT LCD Monitor
1 - Monitor Mounting Stand
1 - Monitor Power Cable with 12 Volt Adaptor
1 - Monitor Power Cable with 12V+, 12V-, and Remote Wire
2 - Sets of Velcro
2 - License Plate Screws
2 - License Plate Bolts & Nuts
4 - Wedge Shaped Mounting shims
4 - In-Line Wire Connectors
1 - Sheet Metal Screw
1 - Grommet
6 - Cable ties
GIVE US A CALL, WE'LL HELP YOU INSTALL.
1-800-445-1797
PLEASE DO NOT RETURN PRODUCT TO STORE.
Visit us on the WEB
www.vr-3.com
For Information and Technical Assistance,
Call Toll-Free in U.S.A. and Canada.
Hard Wired Using Vehicleʼs Reverse Light Circuit for ON/OFF (Fig. 2)
1. Remove the negative battery cable from the vehicleʼs negative battery terminal.
2. Remove the fuses from both of the in-line fuse holders.
3. Connect the Red wire to the 12 Volt +/ACC terminal in the vehicleʼs fuse box. See vehicleʼs
ownerʼs manual for fuse box diagram.
4. For the ground cable locate an area of metal on the vehicleʼs body/firewall that does not have
any vehicle components behind it. Sand off any paint to reveal bare metal, this area will be
your chassis ground.
5. Drill a hole for the supplied self tapping sheet metal screw. Make sure there are not any ve-
hicle components on the other side of where you are drilling the hole.
6. Attach the grounding cable to the chassis ground with the self-tapping sheet metal screw.
7. Next you will need to locate the vehicleʼs reverse light circuit and splice the blue wire into
it using the supplied in-line wire connectors. For help locating the vehicleʼs reverse light
circuit contact your vehicleʼs manufacturer for vehicle specific wiring diagrams.
LED Power Indictor
Image Orientation Button
Power ON/OFF Button
Power Input Jack
(on side of monitor)
MONITOR CONTROLS
Dear Customer,
CONGRATULATIONS. The VRBCS300W Vehicle Reverse Gear Video Camera, when used as
described, will give you years of dependable service in your car, truck, RV, or mini-van. We
have taken numerous measures in quality control to ensure that your product arrives in top
condition, and will perform to your satisfaction. In the rare event that your VRBCS300W
Vehicle Reverse Gear Video Camera contains a damaged or missing item, does not perform as
specified, requires warranty service, or you have an installation problem, DO NOT RETURN
THIS PRODUCT TO THE STORE. PLEASE CALL OUR TOLL FREE NUMBER FROM
THE U.S.A. AND CANADA 1-800-445-1797 and ask to speak with a member of our technical
service team, or submit your questions by e-mail to [e-mail] and a member
of our technical service team will respond by e-mail to your questions. Our in-house technical
service team will expedite delivery of your part, advise you on installation, or help troubleshoot
a problem with you. If your product needs warranty service, our technical service team repre-
sentative will help you obtain the fastest remedy possible under the warranty.
Using the Monitor with the 12 Volt Cigarette Lighter Adaptor
To Fuse Box +12 VDC Acc
To Fuse Box +12 VDC Acc
To Chassis Ground
2.4 GHz WIRELESS MONITOR
MONITOR POWER CABLE
RED
BLUE
BLACK
POWER
A
NGLE
LED
POWER
PLUG
NOTE: When the blue wire is connected to the vehicle’s reverse light circuit
the monitor will come on when the vehicle is put into reverse gear.
FIG. 1
This Schematic is for hard wiring the monitor directly to the vehicle’s fuse box.
In-Line Fuse
In-Line Fuse
To Fuse Box +12 VDC Acc
To +12 VDC Reverse Light Circuit
To Chassis Ground
2.4 GHz WIRELESS MONITOR
MONITOR POWER CABLE
RED
BLUE
BLACK
POWER
A
NGLE
LED
POWER
PLUG
NOTE: When the blue wire is connected to the vehicle’s reverse light circuit
the monitor will come on only when the vehicle is put into reverse gear.
FIG. 2
This Schematic is for hard wiring the monitor directly to the vehicle’s fuse box.
In-Line Fuse
In-Line Fuse
WARNING: Cell Phones and Blue Tooth Products Can Cause Interference.