ABOUT PRIVATE LISTENING When you want to watch without disturbing others, you can use the 2.4G TV Headphones Private Listening feature by inserting headphones and transmitting the sound from the audio transmitter attached to your television. TRANSMITTER Approximately 200ft(60m) maximum wireless range HEADPHONE RECEIVER 2018-11-1 A ZP-2.
IN THE BOX TRANSMITTER & HEADPHONE RECEIVER RCA AUDIO CABLE USB CHARGER
GET TO KNOW YOUR AUDIO TRANSMITTER CHARGING PINS 4 POWER ON/OFF 1 VOLUME CONTROL 2 DSP SELECT SWITCH 3 STATUS LED 5 5V MICRO RECHARGE 6 3.5MM DIRECT LINE-IN JACK 7 MIC. 8 CHARGING PINS 9 POWER/CHARGE INDICATOR 10 DSP SELECT INDICATOR 11 DSP: original sound ---no light musical mode---orange light film mode---blue light OPTICAL-RCA/3.
HOW TO SETUP YOUR AUDIO TRANSMITTER 1.Connect the supplied USB charger to the audio transmitter’s USB port labeled “POWER” . POWER When connected to a power source, the audio transmitter’s LED indicator will light up in green and then turn off enter to standby . LED INDICATOR NOTE: A steady green light indicates that the audio transmitter is paired to the headphone(by default).
HOW TO SETUP YOUR AUDIO TRANSMITTER 2.Connect the white and red plugs of the supplied RCA/3.5mm audio cable to the (L) and (R) AUDIO OUT on your television’s connection panel. NOTE: Ensure the cables are NOT plugged into the TV ’s audio input. 3. Connect the 3.5mm stereo plug to the audio transmitter’s “STEREO IN ” port as shown below. NOTE: The Private Listening feature DOES NOT SILENCE the audio that may be playing through your television’s built-in speakers, sound bar or other connected A/V equipment.
OTHER CONNECTION OPTIONS If your devices have the 3.5mm jack audio output ,you can use the 3.5MM Male to Male Audio Cable to connect the “STEREO IN” of the transmitter and the 3.5MM jack of your audio source . ♫ 3.5MM AUDIO OUT PC 3.5MM MALE TO MALE AUDIO CABLE (not included) The audio sources include TV , smartphone, MP3 player, tablet , portable speakers and other digital devices. NOTE: When an audio source is connected to the audio transmitter's “STEREO IN” , you can switch to the RCA/3.
OTHER CONNECTION OPTIONS If you have a sound bar or other audio equipment already connected to your television’s audio jacks, you can use the audio transmitter’s audio passthrough connection labeled “(L) OUT” and “(R) OUT” to connect to your other audio equipment.
OTHER CONNECTION OPTIONS Using an S/PDIF optical cable for digital audio For televisions equipped with an S/PDIF optical output, you may connect an optical cable (not included) to the TV’s connection panel. Connect the other end of the optical cable into the audio transmitter’s “OPTICAL IN” port (supports 96kHz/24bit). OPTICAL-RCA/3.
PRIVATE LISTENING THROUGH YOUR HEADPHONE Turn on the headphone by pressing the power button for about 2 seconds. The LED will light up in blue. If no Audio Signal detected, the blue light will be turned out after 5 minutes. STATUS LED POWER ON/OFF VOLUME CONTROL NOTE: Adjust the size of the Headband, place the Headphone on your head. To obtain the desired sound level, adjust the Volume Control on the Headphone.
PRIVATE LISTENING THROUGH YOUR HEADPHONE This Headphone can be used as a regular Wired Headphone by connecting your Audio Source with the 3.5MM Male to Male Audio Cable to the Headphone Jack shown below. Note : When plugged in the cable , the headphone will be turned off automatically. ♫ 1. Place the headphone on the headphone holder of the transmitter ,the headphone automatically switch off and the charge status LED on the transmitter and headphone all light up red .
PRIVATE LISTENING THROUGH YOUR HEADPHONE PRIVATE LISTENING THROUGH YOUR HEADPHONE Use the advanced DSP technology to provide excellent sound quality of the concert hall mode, as well as shock bass and 3D surround sound theater mode. DSP SELECT INDICATOR 1. ORIGINAL SOUND---NO LIGHT 2. MUSICAL MODE— ORANGE LIGHT 3.
PAIRING MODE The headphones and the transmitter enclosed in this package have been paired from the factory . To enter pairing mode: 1 .Connect the audio transmitter to a power source and turn the headphones on . 2. Locate the DSP SELECT SWITCH on the headphones ,and press it for more than 3 seconds . PAIRING BUTTON The Status LED on the headphones will be flashing . 3. Locate the Pairing button on the bottom of the transmitter,and press it for more than 3 seconds .
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
