User's Manual

ManualsBrandsShenZhen Zhongherong Electric Technology ManualsToys & GamesRemote Control Toy Transmitter

When the throttle stick is pushed downward.

the speed of the motor and main rotor

increases, as a result, the helicopter descends.

When the throttle stick is pushed upward,

the speed of the motor and main rotor

increases, as a result, the helicopter lifts up.

When the aileron stick is moved to the

right, the swashplate also tilt to the right,

and the helicopter moves to the right.

When the aileron stick is moved to the left,

the swashplate also tilt to the left, and the

helicopter moves to the left.

Model 2 (left throttle)

2.4G

2.4G TRANSMITTER INSTRUCTION MANUAL

2.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.

Summary of content (11 pages)

PAGE 1
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL 2 Model 2 (left throttle) When the aileron stick is moved to the left, the swashplate also tilt to the left, and the helicopter moves to the left. When the aileron stick is moved to the right, the swashplate also tilt to the right, and the helicopter moves to the right. When the throttle stick is pushed upward, the speed of the motor and main rotor increases, as a result, the helicopter lifts up. When the throttle stick is pushed downward.
PAGE 2
.4G 2.4G TRANSMITTER INSTRUCTION MANUAL When the elevator stick is pushed backward, the nose of the helicopter will tilt upward, then the helicopter moves backward and its speed increases. The rudder stick operation for Model 2 is the same as Model 1 ADJUSTMENTS BEFORE FLYING The meso-position of each operating stick, aileron and rudder had already set in the factory, you can adjust it according to your needs. If need adjustment ,you can adjust according to your remote products.
PAGE 3
PAGE 4
PAGE 5
PAGE 6
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL / Throttle/pitch curve diagram THR PIT Output Value NOR Output Value 100% 100% 50% 50% 0% Endpoint L 1 2 3 THR IDEL UP 0% H Endpoint L 1 2 3 PIT Output Value H Output Value 100% 100% 50% 50% 0% Endpoint L 1 2 3 0% Endpoint H L 1 2 3 H Hovering Pitch knob The hovering pitch knob function is to shift the center point of curve either upward or downward to adjust totor RPM at the hover position.
PAGE 7
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL PITCH TRIM KNOB Output Value 0 PITCH 100% The pitch trim knob is a trimmer for the pitch channel .This knob should be set to at first ,then adjust the rotor RPM by shifting it upward or downward. As the setting of each manufacturer is different ,only small trim adjustment will be required if the pitch curve had set properly.
PAGE 8
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL 4 5 4. At last, check the range curve of each servo direction, turn the servo horn rod outward if the range is too small and turn it inward while the range is too large. 5. After finishing all the connections, recheck the operating direction and setting etc. Please charge with an adapter, overcharge or overheating may cause burn or fire etc. or combustion.
PAGE 9
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL + - LED) Always be sure that the batteries are loaded in the correct polarity order. If the batteries are loaded incorrectly, the transmitter will be unworkable . Please take the battery out during the suspended period, please clean it with dry cloth if there is some liquid leaking out from the battery. When the green lamp of the battery voltage indicator(LED) goes off or the Red LED flashes, please exchange the batteries or charge them immediately. 2.
PAGE 10
2.4G 2.4G TRANSMITTER INSTRUCTION MANUAL TRAINER 19 2.4G Remote control system adopts Advanced Spread Spectrum Technology and digital FSK (frequency shift key) Coding Technology.
PAGE 11
The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.