Instruction Manual
8
9
10 11
12 13
1.Insert the CD-ROM,click on the file(58/80 series printer driver software )to
star to installation ,select the language appears as you need to install the
driver,as shown below:
2.Then select the language click “OK”,as shown below ,click”Continue”to next
step.
3.please read the following License Agreement ,accept and continue
the installation , as shown below:
4.Click :N ext”after the operation in the below figure(Customer can also modify
the path of the driver can choose the default installation path)
5.Then click”Next”after the operation as shown below ,choose “install”, if you
computer has antivirus software ,appears to block the installation of the
windows allow this operation.
6.Wait for the installation interface appear as follows after the completion ,
choose your computer’s operating system ,then select the printer model
(POS58 series printer),if you use a USB interface to communicate , click
“USB Port Check”automatically recognize the computer USB port ,click
Next to continue ,as shown below:
7.Click Begin Setup ,as shown below appears ,select “install”or “ install this
driver software anyway”
8.Completing the driver installation ,as shown below:
If the printer prints a normal page, then it shows that the work was successful.
Note: If the printer prompts "Print Error", please return to the "port" option from
the "USB001" started trying to choose
The printer does not print clearly and the thermal paper is Ok.
The printer Print pages lengthways is not clear
It’s getting too noisy while feeding paper or printing.
When the printer has the following conditions, you should clean
the printer head:
1
2
3
1. Power off the printer and open the paper room cover. Remove the
thermal paper roll.
2. If the printer just finished printing , please wait for the print head to
cool down.
3. With a soft cotton cloth dipped in ethanol (please make sure there is
no dripping), wipe the thermal printer head gently and remove any
dust or stains.
4. Wait for the complete evaporation of any ethanol, then place the
thermal paper roll back in the printer and close the paper room cover,
then print a test page.
Notes：
When the printer maintenance must ensure that the power is shut down
Hands or other metal tools away from the surface of the printer head,
do not u se tweezers to scratch the surface of the printer head and
other sensitive p a rts.
Do not use gasoline, acetone and other organic solvents for printer
head cleaning.
1: Self printing test is ok,but printer does not work after driver installation.
A: Recheck the installation according to above installation wizard and see
if we selected the right port or ask service center for advice if needed.
2: Malfunction of paper feeding?
A: Use soft brush to clean the paper sensor and try again or send it to the
service center for repair.
3．Malfunction of the indicator light
A: Check the cable connecting way / adapter / power cord / switch on or off?
Or contact the service center for repair.
4．Messy code printing except Arabic numeral printing.
A: language switching incorrectly, please use our tool "IPrinter" (you can find it
on the enclosed CD) to change the language what you want print.
5．Red indicator keep flashing during the printing.
A: Usually it is due to the high temperature of the print head. If printing stopped,
please contact the service center for repair.
6. Printing speed is very slow for serial printer
A: follow this path and change the set accordingly : Driver -- Properties -- Device
Settings -- Print Mode -- Print as soft font.
7. Water or other liquid spills into the printer
A: Cut off the power,we can dry the main board or printer head with a hair dryer,
careful of the temperature ( average 50 degree is ok )
9. The printer can't work
A：The battery maybe without electricity，please use power adapter to
charge. Then you try to star the printer, if the printer has same problem, please
send to service center for repair.
10. Can not search the Bluetooth printer
A：Please check the equipment "Bluetooth" function whether opened, the
communication whether normal, then replug the printer "Bluetooth Module"
try to connect and search “Bluetooth” again, if the problom are still existed,
please send the specified location repair.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.