O P E R A T I N G I N S T R U C T I O N S BEDIENUNGSANLEITUNG STEREO INTEGRATED AMPLIFIER D A S AX-4103 DISCRETE AMPLIFIER STAGE VOLUME TONE BALANCE REMOTE SENSOR STANDBY TUNER CD TAPE TV/AUX VCR TONE DIRECT POWER PHONES A SPEAKER B AX-4103 STEREO INTEGRATED AMPLIFIER INTEGRIERTER STEREO VOR-/ENDVERSTARKER
Introduction ENGLISH UNPACKING AND INSTALLATION Congratulations on Your Purchase! Your new high fidelity amplifier is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material.
FOR U.S.A AND CANADA .................................. 120 V FOR OTHER COUNTRIES ........................ 115 V/230 V FOR YOUR SAFETY FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only. Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch. Safety precaution with use of a polarized AC plug.
ENGLISH CONTENTS Introduction UNPACKING AND INSTALLATION ....................................................................................................... 2 READ THIS BEFORE OPERATING YOUR UNIT................................................................................... 3 System Connections ....................................................................................................................................... 5 Front Panel & System Remote Controls ...............................
Do not plug the AC input cord into the wall AC outlet until all connections are completed. Be sure to connect the white RCA pin cord to the L(left) and the red RCA pin cord to the R(right) jacks when making audio connections. Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the amplifier. If the electricity fails or the AC input cord is left unplugged for more than 2 weeks, the memorized contents will be cleared. Should this happen, memorize them again.
ENGLISH ■ AC INPUT CORD Plug this cord into a wall AC outlet. ■ SWITCHED AC OUTLET ■ CONNECTING SYSTEM CONTROL • This outlet is switched on(power-on mode) and off(standby mode) according to power control as follows(Maximum total capacity is 100W): Sherwood component with DIGI LINK II or III CD player Tape deck Standby mode — switched AC outlet off Power-on mode — switched AC outlet on System control cord Tuner, etc.
Front Panel & System Remote Controls STEREO INTEGRATED AMPLIFIER D A S AX-4103 DISCRETE AMPLIFIER STAGE VOLUME TONE BALANCE REMOTE SENSOR STANDBY TUNER CD TAPE TV/AUX VCR TONE DIRECT POWER PHONES A SPEAKER B System Remote Controls • You can remotely control not only this amplifier but also Sherwood compatible components bearing the DIGI LINK II or III logo. • For system remote control operation, first make the DIGI LINK connections.
ENGLISH ① POWER SWITCH Push this switch to enter the standby mode. To switch the power off, push again this switch. ⑩ TONE DIRECT BUTTON Press this button to listen to a program source without the tone effect. ② STANDBY INDICATOR ⑪ VOLUME CONTROL KNOB, UP/DOWN( ∧/ ∨) BUTTONS Adjust the volume to a comfortable listening level with this knob or these buttons. ③ POWER BUTTON In the standby mode, press this button to turn the power on, then the STANDBY indicator goes off.
ENGLISH FLUORESCENT DISPLAY REMOTE CONTROL OPERATION RANGE STEREO INTEGRATED AMPLIFIER LOADING BATTERIES 1 Remove the cover. 2 Load two batteries matching the polarity. D A S AX-4103 DISCRETE AMPLIFIER STAGE VOLUME TONE BALANCE REMOTE SENSOR STANDBY TUNING/PRESET TUNER CD TAPE TV/AUX VCR TONE DIRECT POWER PHONES A SPEAKER B 7m 30 30 POWER 1 2 3 6 7 8 DISC 4 5 9 0 REPEAT INTRO A<>B CD DECK SEL. DECK INPUT SELECTOR CD VCR AUX TAPE SLEEP DISPLAY FM MODE P.
Operations ENGLISH LISTENING TO A PROGRAM SOURCE Before operation Enter the standby mode. 3 STANDBY TUNER Select the desired input source. CD TAPE TV/AUX VCR POWER The STANDBY indicator lights up. This means that the amplifier is not disconnected from the AC mains and a small amount of current is retained to support the memorized contents and operation readiness. To switch the power off, push the POWER switch again, then the power is cut off and the STANDBY indicator goes off.
8 9 Enter the tone mode. At the desired tone mode, adjust the tone as desired. POWER POWER 1 2 3 6 7 8 4 5 9 0 REPEAT INTRO 1 2 3 6 7 8 4 DISC 5 9 0 REPEAT INTRO A<>B DISC A<>B TONE CD CD A DECK SEL. A DECK B DECK SEL. DECK B or INPUT SELECTOR or CD VCR AUX TAPE SLEEP DISPLAY FM MODE P.SCAN INPUT SELECTOR TREBLE/BASS CD VCR AUX TAPE SLEEP DISPLAY FM MODE P.SCAN MEMORY TUNER MEMORY TUNER TONE SEL. A TONE SEL.
ENGLISH RECORDING The volume, tone(bass, treble) and balance settings have no effect on the recording signals. When you select tuner, CD or AUX as a recording source, recording may be made on TAPE or VCR, or both simultaneously. Recording with TAPE 1 Recording with VCR Select the desired input as a recording source except for TAPE. TUNER CD TV/AUX 1 VCR Select the desired input as a recording source except for VCR.
If a fault occurs, run through the table below before taking your amplifier for repair. If the fault persists, attempt to solve it by switching the amplifier off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you repair the amplifier yourself as this could invalidate the warranty. PROBLEM POSSIBLE CAUSE REMEDY No power • The AC input cord is disconnected. • Poor connection at AC wall outlet or the outlet is inactive. • Connect the cord securely.
O P E R A T I N G I N S T R U C T I O N S AX-4103 STEREO INTEGRATED AMPLIFIER INTEGRIERTER STEREO VOR-/ENDVERSTARKER 5707-21055-001-0