Owner`s manual

ManualsBrandsSherwood ManualsLawn and GardenEG28 BV

EG28-121

This appliance may be installed in an after market

permanently located, manufactured (mobile)

home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless a

certied kit is used.

WHAT TO DO IF YOU SMELL GAS

• Open windows/Extinguish any open ame.

• Do not try to light any appliance.

• Do not touch any electrical switch or use any

phone in your building.

• Immediately call your gas supplier from a

neighbour’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call the

re department.

WARNING

If the information in this manual is not followed exactly, a re or explosion may

result causing property damage, personal injury or loss of life. Installation and

service must be performed by a qualied installer, service agency or the gas supplier.

FOR YOUR SAFETY: Do not store or use gasoline or other Flammable vapours and

liquids in the vicinity of this or any other appliance.

Massachusetts installations (Warning): This product must be installed by a licensed

plumber or gas tter when installed within the Commonwealth of Massachusetts. Other

Massachusetts code requirements: Flexible connector must not be longer than 36in., a

shut off valve must be installed; only direct vent sealed combustion products are approved

for bedrooms/bathrooms. A carbon monoxide detector is required in all rooms containing

gas red direct vent appliances.

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PAPER.

B Y : S H E R W O O D I N D U S T R I E S L T D

OWNER’S MANUAL

PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE

EG28 BV

WARRANTY REGISTRATION

enviro.com/warranty

Summary of content (26 pages)

PAGE 1
EG28 BV BY: SHERWOOD INDUSTRIES LTD N IO AT TR ty I S ra n EG ar R /w T Y c om N A ir o . R R e nv A W SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER. OWNER’S MANUAL PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHAT TO DO IF YOU SMELL GAS • Open windows/Extinguish any open flame. • Do not try to light any appliance. • Do not touch any electrical switch or use any phone in your building.
PAGE 2
Safety Precautions FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION: • All ENVIRO gas-fired appliances must be installed in accordance with their instructions. Carefully read all the instructions in this manual first. Consult the building authority having jurisdiction to determine the need for a permit prior to commencing the installation.
PAGE 3
Table of Contents Safety Precautions............................................................................................2 Table of Contents..............................................................................................3 Codes And Approvals........................................................................................4 Specifications...................................................................................................5 Dimensions...................................
PAGE 4
Codes And Approvals BV: This Vented appliance draws all of its combustion air from the dwelling and must be vented using listed B or L vent. May also be vented through a conventional chimney using a chimney liner kit. This appliance has been tested and approved for installations from 0 feet to 2000 (610 m) above sea level. In the USA: The appliance may be installed at higher altitudes.
PAGE 5
Specifications Dimensions: Shipping Weight 210 lbs (95 kg) 11" (279 mm) 4" (102 mm) 19" 27 1/2" (483 mm) (699 mm) 22" (559 mm) Figure 1: EG28 Exterior Dimensions. Rating Label Location: The rating label is found inside the right cabinet side panel.
PAGE 6
Operating Instructions FOR YOUR SAFETY READ COMPLETELY BEFORE OPERATING. Lighting Instructions: TP TH H TP TH L ON LO PI T WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage, or loss of life. Refer to owner's information manual provided with this appliance. For assistance or additional information consult a qualified installer, service agency or the gas supplier. See installation and operating instructions accompanying appliance.
PAGE 7
Operating Instructions Thermopile Thermocouple Figure 3: Pilot Burning. Figure 4: Gas Valve. Adjusting The Venturies: • Remove the ash shelf by undoing the screw at each end, pull shelf towards you. • Remove one screw from the cover plate located below the ash shelf. Loosen the other screw (do not remove) swing the cover plate out of the way and tighten screw down to hold it in place. • With along screwdriver rotate spring clips to open or close the shutter to the desired setting.
PAGE 8
Maintenance and Service Periodically check to ensure that your direct vent system is clean. Periodically check the pilot and burner. Check to see that all the burner ports are clean and clear. Check the pilot head for blockage. Check to ensure the pilot flame is blue with no or very small yellow tips. Opening The Door: Turn unit off and wait until the appliance has cooled down. 1. Open the right hand hinged side flap, which will expose a door fastener. Using a ½” wrench, loosen the fastener. 2.
PAGE 9
Maintenance and Service Cleaning Plated Surfaces: It is important to note that fingerprints and other marks can leave a permanent stain on plated finishes. To avoid this, give the face a quick wipe with denatured alcohol on a soft cloth BEFORE lighting the fireplace. Never clean the face when it is not cool. Do not use other cleaners as they may leave a residue, which can become permanently etched into the surface.
PAGE 10
Maintenance And Service Fuel Conversion: TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY Please read and understand these instructions before installing. Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction.
PAGE 11
Maintenance And Service 7. Convert the SIT gas valve: a) Remove the black protection cap from the HI/LO knob by hand shown in Figure 9. b) Insert a 5/32” or 4 mm Allen wrench into the hexagonal key-way of the screw (see Figure 10), rotate it counter-clockwise until it is free and extract it. c) Check that the screw is clean and if necessary remove dirt. Loosen d) Flip the screw (refer to Figure 11).
PAGE 12
Initial Installation QUALIFIED INSTALLERS ONLY WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. Preparation For Installation: • Remove the packaging from the appliance, and check to make sure there is no damage. If damage is found, please report it to both the carrier and your dealer as soon as possible.
PAGE 13
Initial Installation QUALIFIED INSTALLERS ONLY Venting: This model must have a vent opening in the rear of the unit. Confirm this and also check that the label on the right side panel door states “Vented Room Heater”. WARNING: This appliance has been designed to operate by drawing combustion air and dilution air from the room. The draft hood located in the same atmospheric pressure zone as the combustion air inlet to the appliance.
PAGE 14
Initial Installation QUALIFIED INSTALLERS ONLY Termination: 10 ft (3050 mm) The bottom of the vent cap shall extend at least 2 feet (0.61 m) above the highest point of the roof where it passes through and at least 2 feet (0.61 m) higher than any portion of the roof within a horizontal distance of 10 feet (3.1 m).
PAGE 15
Initial Installation QUALIFIED INSTALLERS ONLY Straight Vertical Installation: This basic venting configuration shown are rough guidelines only. Follow national and local codes for other installation options. For the best venting performance, we recommend a total vent height in the range of 10 feet (3.0 m) to 30 feet (9.1 m). The total horizontal length depends on the number of elbows used; a 90° elbow accounts for 5 feet (1.5 m) of the horizontal run.
PAGE 16
Initial Installation QUALIFIED INSTALLERS ONLY Electrical Requirements: THERM ON TP/TH OFF The ENVIRO EG28 will operate without electrical power. This model has a millivolt gas control, which uses the pilot flame to generate enough electricity to operate the main burners. The appliance is equipped with a blower and must be electrically connected Fan Controller and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.
PAGE 17
Initial Installation Gas Line Connection and Testing: WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance. GAS LINE CONNECTION • This stove is equipped with a certified flexible pipe located on the right side of the unit terminating in a ⅜” male NPT fitting.
PAGE 18
Secondary Installation Installation of Log Set and Embers: The placement of the logs is not arbitrary. If they are positioned incorrectly, the flames can be “pinched” and will not burn correctly. The burner come with five (5) locator pins and two (2) resing areas, which make alignment easier. Using the pictures provided, carefully set the logs in place. NOTE: The logs are fragile and should be handled gently. Figure 20: Step 1 of Log Placement.
PAGE 19
Secondary Installation 3. Place the log set into the firebox. Locate each log by seating it down onto the burner tray support pins. Follow Figures 11 to 16 proper log placement. 4. Upon the first light up, watch for ignition to ALL burner ports. If a long delay is noted: First, wait for the appliance to cool down. • Open the front door of the appliance. Resting Areas for Center Log Figure 24: Step 5 of Log Placement.
PAGE 20
Trouble Shooting Problem Possible Cause The main burner The gas valve may not be on. does not ignite Thermostat is not calling for when called for. heat. • Check that the gas control knob is in the “ON” position. • Adjust the thermostat several degrees above ambient temperature. Problem with gas valve. • Use a DC voltmeter to measure the voltage across the TPTH and TP terminals.
PAGE 21
Parts List Reference Number Part Description Part Number 1 120°F (49°C) Ceramic Temperature Sensor EC-001 2 Spill Switch 220°F (121°C) EC-002 3 Thermocouple EC-009 3 Spark Electrode with Cable EC-011 3 Thermopile EC-012 3 Pilot NG with Electrode EC-013 3 Pilot LP with Electrode EC-014 3 Fully Assembled Pilot NG EC-015 3 Fully Assembled Pilot LP EC-016 3 Pilot Orifice NG EC-019 3 Pilot Orifice LP EC-020 Pilot Gasket EC-021 4 S.I.T.
PAGE 22
Parts List Reference Number 16 Burner Tray Top Part Number EG28-116A BV Owner’s Manual EG28-121 17 Cabinet Side Panel EG28-123 18 BV Stove Top EG28-124 Firebox Baffle EG28-125 Fan Kit EG28-127 19 BV Top Baffle EG28-132 20 Wire Channel EG28-139 Pedestal Wiring Plate EG28-140 21 Pedestal Back EG28-141 22 Ash Shelf EG28-150 Door Hinge Bracket EG28-161 23 Door Latch Bracket EG28-162 24 BV 4” Crimped Flue Pipe EG28-169 25 Glass Set with Gasket EG28-205 Thermocouple Pilot N
PAGE 23
Parts Diagram - Chassis 24 18 1 19 31 26 17 20 12 2 7 33 17 14 21 8 15 EG 28 Body (Chassis) April 2006 23
PAGE 24
29 24 28 27 11 16 10 5 6 4 32 3 13 35 April 2006 34 31 25 9 EG 28 Gas Tray and Door Assemblies 23 Parts Diagram - Gas Tray & Door
PAGE 25
Warranty for Enviro Gas Products Sherwood Industries Ltd. (“Sherwood”) hereby warrants, subject to the terms and conditions herein set forth, this product against defects in material and workmanship during the specified warranty period starting from the date of original purchase at retail. In the event of a defect of material or workmanship during the specified warranty period, Sherwood reserves the right to make repairs or to assess the replacement of a defective product at Sherwood’s factory.
PAGE 26
Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference.