R-807 Network AV Receiver Récepteur réseau AV Receptor A/V con conexión de red Netzwerk-AV-Receiver Сетевой AV-ресивер OPERATING INSTRUCTIONS GUIDE D’UTILISATION INSTRUCCIONES DE FUNCIONAMIENTO BEDIENUNGSANLEITUNG ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИИ
Safety Information READ THIS BEFORE OPERATING YOUR UNIT CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE FRONT OR BACK COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
Table of Contents 2 Safety Information 5 Getting Started 5 What's Included 6 Installing the Remote Control Battery 6 Operating the range of the Remote Control 7 Parts Description 7 Front Panel 8 Front Display 8 Rear Panel 9 Remote Control 26 Operating Your System 10 Making Connections English 26 Listening to Your System 26 Basic Operation 26 Muting the Sound 27 Enjoying Surround Effects 27 Setting the Surround Mode 30 Cancelling the Surround Mode for Stereo Operation 30 Adjusting the
R-807 Network AV Receiver 42 Customizing Settings 42 Setting the System 43 Setting Options Overview 44 Setting the System Setup 44 AMP Assign 44 Automatic Power Control 44 Network Standby Control 44 Setting the Speaker Setup 44 46 46 46 46 Auto Setup Speaker Setup Speaker Crossover Speaker Distance Speaker Channel Level 47 Setting the HDMI Setup 47 HDMI 47 CEC Control 47 Setting the Surround Parameter Setup 47 47 47 47 47 48 48 48 48 Height Gain PANORAMA Center Width Dimension Center Image DRC Tone So
Getting Started English What's Included Main unit Battery Remote control (1 ea) Power Cable (1 ea) Setup Mic (1 ea) R807 NETWORK AV RECE VER OP RA ING NS RUC IONS FM antenna (1 ea) AM Antenna (1 ea) User Manual 5
R-807 Network AV Receiver Installing the Remote Control Battery 1 2 Remove the battery cover. Insert two AAA size batteries with the polarity matched properly. Caution •• Always use alkaline batteries, and do not use the rechargeable batteries (Ni-Cd type). •• If the batteries run out, remove the old batteries and replace them with new ones within several minutes. •• If the batteries are removed or have been exhausted for a longer period of time, memorized contents will be cleared.
Parts Description 1 2 9 1 2 3 4 5 6 7 8 3 45 10 11 12 Main Power Switch Standby Indicator On/Standby Switch IR Sensor Band Select Button Display Surround Select Buttons Master Volume Control 6 13 7 14 9 10 11 12 13 14 15 16 15 English Front Panel 8 16 Input Selector Headphone Connector Aux Input Connector Setup MIC Connector Tuning Up/Down Buttons Preset Select Buttons Stereo Mode Button USB Port 7
R-807 Network AV Receiver Front Display 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 18 1 2 3 4 5 6 7 8 9 17 10 11 12 13 14 15 16 17 18 Information Display Dolby Digital Surround indicator Auto Detecting Indicator RDS Indicators Stereo Indicator Tuning indicator Room2 Indicator USB Indicator MP3 Indicator 16 WMA Indicator Sleep Timer Indicator Preset Indicator Station Memory Indicator Preset Station Indicator Direct Indicator HDMI Indicator Digital Input Indicator Dolby/DTS/DSP Surround mode indicators
Parts Description Remote Control 1 2 24 23 22 3 21 1 2 3 4 5 6 20 4 5 6 19 18 17 16 7 8 9 10 Power On Button English 25 Room2 Input Select Button Source Select Buttons Surround Select Buttons Top Menu Button ▲/▼/◄/► Select Buttons ENTER/MEMO Enter/Memory Button SEARCH.
Making Connections Connection Overview Connect various external devices to the ports on the main unit. 1 2 3 Find an external device you want to connect to the main unit as shown on the following illustration. Check the connection type of the external device. Go to the appropriate illustration and check the connection details. Speaker System BD/BDR See page 11. HDMI IN - See page 15. VIDEO IN/OUT - See page 17, 20. DIGITAL IN - See page 18. AUDIO IN/OUT - See page 19, 20.
Making Connections Connecting Speakers English Placing Speakers Determine the locations for your speaker placement according to their manufacturer’s directions and the layout of your listening room. Use the illustration on page 12 as a guide for speaker placement. To create the most realistic surround-sound environment possible, you should place your speakers in a circle around the listener. You should angle each speaker so it directly faces the listening position. Use the diagram below as a guide.
R-807 Network AV Receiver FHR FHL TV FL SW FR C SR SL SBL SBR SB Surround back left and right speakers •• Place the surround back speakers at the back facing forward together and closer than front speakers. •• When using a single surround back speaker, place it at the rear center facing forward at a slightly higher position (0 to 20 cm) than the surround speakers. •• We recommend installing the surround back speaker(s) facing slightly.
Making Connections Connecting Speakers English Carefully check the left (L) and right (R) channels and the polarities on the speakers being connected to this receiver. Connecting Speaker Wires 1 2 Strip away approx. 10 mm (3/8 inch) of wire insulation, and then tightly twist the wire ends. 3 4 Loosen the speaker terminal by turning it counter-clockwise. Insert the bare part of the wire. Tighten the speaker terminal by turning it clockwise.
R-807 Network AV Receiver •• Be sure to connect speakers firmly and accurately according to the channel (left and right) and the polarity (+ and −). If the connections are incorrect, no sound will be produced by the speakers, and if the polarity of the speaker connection is incorrect, the sound will be unnatural and tinny. •• When listening in Dolby Pro Logic IIz mode, connect the front height speakers. •• To install the speakers, see “Placing Speakers” on page 11.
Making Connections You can skip the “Crossover” setting. 8 Measure the distance from each speaker in your system to the listener. Set the distances. 9 10 11 12 Select “Speaker Distance”. The Speaker Distance menu will appear. Use the remote’s left and right arrow buttons to change the distance setting for each speaker so that it matches the distance you wrote down in step 8. When you’re finished, press the remote control’s RETURN button to return to the Speaker Setting menu.
R-807 Network AV Receiver HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs. This main unit is also compatible with the DeepColor and x.v.Color feature (x.v.
Making Connections Source devices are components from which a playback signal originates, e.g., a Blu-ray Disc™ or DVD player; a set-top box, or HDTV tuner, etc. The receiver has several different types of input connectors for your audio and video source devices: HDMI, composite video, optical digital audio, coaxial digital audio and analog audio. Connecting Video Components You will need to make composite video connections from your source devices that do not have HDMI video connections.
R-807 Network AV Receiver Connecting Audio Components Coaxial Digital Audio Connection Optical Digital Audio Connection If your source devices have a coaxial digital output, connect it to the main unit's coaxial digital audio connector. You can connect components equipped with an optical output jack. On the main unit, you can enjoy the full sound of components, such as DVD players, set-top box, BD (Blu-ray Disc™) players or TVs. * “Blu-ray Disc” is a trademark of Blu-ray Disc Association.
Making Connections F.AUX Connection Make analog audio connections from your source devices that do not have HDMI or digital audio connections. If you’re connecting video sources to the main unit, you must also connect the source device’s composite video output to the corresponding composite video connector. You can use the F.AUX input jack to connect portable audio components such as an MP3 player, etc.
R-807 Network AV Receiver Connecting Recording Components You can connect video and audio recording devices to the VIDEO OUT and AUDIO OUT jacks. You can make an audio or a video recording from the built-in tuner or from an audio or video source connected to the main unit. Rear Panel Connecting to a Network If you have an internet connection, you can connect the main unit to the internet as well as using a wireless or a wired LAN connection.
Making Connections Connecting an Antenna Connecting FM Antenna To strengthen the signal reception, extend the antenna to its full length. Outdoor Antenna 1 2 English To listen to radio stations, connect the FM wire antenna and AM loop antenna as illustrated below. Remove the indoor antenna if it is connected. Connect the FM outdoor antenna to the FM antenna terminal. Indoor Antenna 1 2 Connect the FM indoor antenna to the FM antenna terminal.
R-807 Network AV Receiver Connecting AM Antenna 1 2 3 Assemble the AM loop antenna as illustrated below. Place the antenna as far as possible from the main unit, TV set, speaker cords and the AC input cord, and set the direction for the best reception. Rear Panel If the reception is poor with the AM loop antenna, it is recommended to replace it with an AM outdoor antenna.
Making Connections Connecting to Muti-Room English The multi-zone function allows you to play back different input sources in the room where the unit is installed (Main Room) and in another room (Room2). Main Room You can enjoy sounds from the equipment connected to the main unit in a room other than the main room. For example, you can watch the DVD in the main room and listen to a CD in the sub room.
R-807 Network AV Receiver Connecting to the System's Internal Amplifier Connect the speakers placed in Room2 to the main unit with speaker cables. Rear Panel Connecting to an External Amplifier Connect the external amplifier (with volume control) placed in Room2 to the main unit with analogue audio cable.
Making Connections 4 Connect the external amplifier (with volume control) placed in Room2 to the unit with analogue audio cable. You can select different sources for main room and second room (ROOM 2) and play them at the same time. 1 •• The tone level can be adjusted within the range of -10 ~ +10 dB. •• In general, we recommend the bass and treble to be adjusted to 0 dB (flat level). Press ROOM2 on the remote control. •• The ROOM 2 indicator is displayed on the fluorescent display.
Operating Your System Listening to Your System Basic Operation You can listen to audio by following the basic procedures below. 1 Turn on the connected component. 2 4 Start playback of the component you selected in step 1. 5 During playback, you can adjust the volume level. •• On the main unit, rotate the volume controller. •• On the remote control, press VOLUME -/+. Turn on the main unit. •• On the main unit, press POWER and ON/ STANDBY. •• On the remote control, press POWER ON and STANDBY.
Operating Your System Enjoying Surround Effects English This main unit incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. Setting the Surround Mode Before surround playback, first perform the speaker setup procedure, etc. on the OSD settings for optimum performance. For details, see “Setting the Speaker Setup” on page 44. 1 Select the desired surround mode by pressing the SURROUND buttons.
R-807 Network AV Receiver DTS Digital Surround Dolby Digital DTS Digital Surround (also called simply DTS) supports up to 5.1 discrete channels and uses less compression for high fidelity reproduction. Use it with DVDs and CDs bearing the DTS logo. Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories. Discs bearing the Dolby Digital logo include the recording of up to 5.1 channels of digital signals.
Theater Stadium This mode provides the effect of being in a theater when watching a play. This mode provides an expansive sound field in order to achieve a true stadium effect when watching baseball or soccer games. Movie Multi Channel Stereo This mode provides the effect of being in a movie theater when watching a movie. This mode is designed for playing background music. The front, surround and surround back channels create a stereo image that encompasses the entire area.
R-807 Network AV Receiver Cancelling the Surround Mode for Stereo Operation 1 Press STEREO. •• Depending on the input signal format, either the stereo mode or the 2CH downmix mode is selected. 2 To cancel either the stereo mode or the 2CH downmix mode, press the SURROUND buttons to select the surround mode. Adjusting the Current Channel Level After adjusting each channel level with test tone, adjust the channel levels according to the program sources or to suit your tastes.
Operating Your System Listening to Music on USB English You can play audio files from a USB device. However, editing or copying a data file is not possible. To Pause Playback 1 During playback, press . •• Playback will stop at the point where the button is pressed. •• To resume playback from this point, press the button again. USB storage device Note •• The USB jack does not support the connection of other USB devices except for a USB flash drive or a USB memory card reader.
R-807 Network AV Receiver Listening to Internet Radio To Play Repeatedly 1 During playback, press REPEAT. Each time the button is pressed, repeat mode changes as follows: •• RPT ONE Repeats the currently playing music file. You can listen to Internet radio broadcasts provided by vTuner. You can control the internet radio with the menu displayed on the TV screen. •• RPT ALL Repeats all music files. •• RPT FLDl Repeats all music files in the folder. 1 Select NETWORK as an input source.
Operating Your System Listening to Music from the Media Server Select the desired category by pressing and , then press ENTER on the remote control. You can play music files stored on a computer (media server) connected to this receiver via a wired or wireless network. You can share the music files easily by using Windows Media Player 11 or later versions.
R-807 Network AV Receiver Listening to Music from the Media Server 1 2 5 Start your computer. Repeat step 3 above until the desired music file is selected. The playback functions are the same as those for USB. Refer to ** for details on playback. Select NETWORK as an input source. •• On the main unit, rotate INPUT SELECTOR. •• On the remote control, press NETWORK.
Operating Your System 1 2 3 4 5 Visit Play Store on your Android Smartphone. Or visit AppStore on your iPhone. Search for Sherwood Remote. Download and install the application on your phone. Open the application. Tap Select Product and R-807. Using the Application The Sherwood Remote application helps you to control the main unit remotely by allowing you to select input source, to set a surround mode, to control Room2, and use Wiink. 1 2 Open the Sherwood Remote application.
R-807 Network AV Receiver Overview of the Main Screen Using Direct AV 8 1 1 2 2 3 4 Tap Wiink at the bottom of the phone screen. Or tap INPUT SELECT and select and tap NETWORK. Tap Direct AV. 7 5 No. 36 On Direct AV, you can listen to songs, watch videos, and view photos stored on your Android phone or iPhone. 6 Description 1 Turns on or off the main unit •• To activates the function, you should set N.S.C to ON. If you set the function on, the power consumption may increase.
Operating Your System Watching Videos on Your Smartphone •• Android 1 You can select a song on the song list and play it over the main unit. 1 8 2 3 7 6 5 4 No. 7 6 2 3 4 Listening to Songs on Your Smartphone English You can select a video on the video file list and enjoy it on the main unit. 5 No. Description 1 Moves to the previous menu •• This menu is not displayed on the Android smartphone.
R-807 Network AV Receiver Viewing Photos on Your Smartphone Using Internet Radio and Media Server You can view photos as a slideshow and set the slideshow transition time at 10, 20, or 30 seconds. You can use your smartphone as a remote controller for Internet Radio and Media Server. 1 2 1 2 No. Tap Wiink at the bottom of the phone screen. Tap Internet Radio or Media Server. 3 Description 1 Moves to the previous menu •• This menu is not displayed on the Android smartphone.
Operating Your System Auto Tuning 1 Press TUNE + or TUNE - for more than 2 seconds. Manual Presetting 1 Tune to the desired station with auto or manual tuning. 2 Press ENTER/MEMO. 3 Select a desired preset number (1~30) by pressing TUNE + or TUNE -. English Listening to FM Radio •• A preset number blinks. •• The tuner keeps searching until a station with strong signal strength is found. The display shows the tuned frequency.
R-807 Network AV Receiver Auto Presetting RDS Tuning 1 RDS (Radio Data System) is a way of sending information signals along with transmitter signals. Your tuner is capable of translating these signals and displaying the information. These codes contain the following information: Program Service name (PS), A list of Program Types (PTY), Traffic Announcement (TA), Radio Text (RT). Press and hold down ENTER/MEMO for more than 2 seconds.
Operating Your System Recording 3 While a desired program type is displayed: •• The tuner automatically seeks a station offering PTY services. •• If no station is found, “NO PTY” is displayed. Displaying RDS information 1 Press DISPLAY. •• The receiver’s volume, Audio parameters (the tone controls, for example), and surround effects have no effect on the recorded signal. •• Some digital sources are copy-protected, and can only be recorded in analog. •• Some video sources are copy-protected.
Customizing Settings Setting the System You can program additional sound settings. 5 1 Press SETUP. 2 Press or to select a main menu. 6 Press or to set a value. 3 Press ENTER/MEMO to confirm. 7 Press ENTER/MEMO to confirm. Press ENTER/MEMO to confirm the selected setting. •• To return to the previous menu, press RETURN. •• To exit the menu, press SETUP again. 4 42 Press or to select an option.
Customizing Settings Main Menu 1. SYS SET 2. SPK SET Sub Menu Go to Page 5. MLT. RM Description AMP 44 Assigns the power amplifier. A.P.C. 44 Automatic Power Control. N.S.C. 44 Sets the standby time for the network. A. SETUP 44 Automatically optimizes the speaker settings. SPK SET 46 Sets the speaker system. X.OVER 46 Sets the crossover frequency. DISTANCE 46 Sets the speaker distance. CH.LEVEL 46 Sets the current channel levels.
R-807 Network AV Receiver Setting the System Setup AMP Assign The surround back channels’ power amplifier can drive surround back speakers, front height speakers, and the ROOM 2 speakers. Depending on the purpose of the speakers, you should assign the power amplifier accordingly. For details, see “Connecting Speakers” on page 13 and “Connecting Multi-Room” on page 23. Menu item Description Surround Back Drives the surround back speakers when connecting the SURROUND BACK channels to them.
Customizing Settings Caution 3 English •• Since the microphone for Auto Setup is designed exclusively for this receiver, do not use a microphone other than the one supplied with this receiver. Place the microphone on a flat level surface at the listening position. •• If possible, use a tripod or to fix the microphone at the same height as your ears would be when you are seated in your listening position. 6 •• The results are memorized and the Speaker Setup menu is displayed.
R-807 Network AV Receiver Speaker Setup Speaker Distance There are several ways you can use the speaker channels with the main unit. In addition to a normal home theater setup where they are used for the front height speakers, they can be used as an independent speaker system in another room. •• Select the desired unit (Meter or Feet) before setting the speaker distance. Once a unit is selected, the distances are automatically converted to the selected unit.
Customizing Settings Setting the Surround Parameter Setup HDMI You can specifies the routing of the HDMI audio signal from the system or through to a TV or flat screen TV. The HDMI connection can carry uncompressed digital video signals and digital audio signals. Depending on whether the digital audio signals input into the HDMI IN are output from the HDMI MONITOR OUT of the main unit or not, you should set the HDMI Audio Output correctly.
R-807 Network AV Receiver 2 DRC This function compresses the dynamic range of previously specified parts of the Dolby Digital, Dolby TrueHD or DTS sound track (with extremely high volume) to minimize the difference in volume between the specified and non-specified parts. This makes it easier to hear the full sound track when watching movies at night at low levels. Menu item Adjust the selected tone as desired by pressing or . •• The tone level can be adjusted within the range of -10 ~ +10 dB.
Customizing Settings In addition to your main room, you can also enjoy playback in Room2. Menu item Network Settings Overview Main Menu Description On Turns on the Room2 function. Off Turns off the Room2 function. NETWORK CONNECT Sub Menu Soft AP Direct hotspot AV Set Wi-Fi direct Wired Note •• When Room2 is set to “OFF”, the input and the volume cannot be selected. •• When you do not use the Room2 function, set the Room2 to “OFF” to save electricity.
R-807 Network AV Receiver Setting the Wired Network Connection Before you setup the connection, check that the LAN cable is connected to the LAN/ETHERNET connector properly and securely. For details, see “Connecting to LAN cable” on page 20. Setting Other Network Options Menu item Description AP Name Views and changes the name of the unit displayed on the network. Ethernet Resolution You can enable and set the Ethernet connection automatically on the main unit.
Troubleshooting If you experience any of the following difficulties while using the system, use this troubleshooting guide to help remedy the problem before requesting servicing. Should any problem persist, consult your nearest authorized dealer or authorized independent company. English If the unit does not operate normally due to external influence such as static electricity, disconnect the power plug from the outlet and insert again to return to normal operating conditions.
R-807 Network AV Receiver Problem Remedy Sound is interrupted or there is noise. •• Check the output audio formats support system. •• Check that the speakers and equipment are connected securely. •• Move your audio equipment away from the TV. •• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with alcohol. No sound is heard or there is noise when software with DTS is played back. •• Set the digital volume level of the system to full, or to the neutral position.
Troubleshooting No picture. Remedy •• Depending on the output settings of the source component, the video format may not be displayed. Change the output settings of the source, or connect your source component directly to TV using the component or composite video jacks. •• This system is HDCP-compatible. Check that the components you are connecting are also HDCP-compatible. If they are not, please connect your source component directly to TV using the component or composite video jacks.
R-807 Network AV Receiver NETWORK CONNECTION Symptom Remedy The main unit cannot connect to the WPS via a wireless LAN connection. •• You cannot connect to a network using WPS when your access point is set to WEP. Set up your network after searching the access point using the access point scan. The receiver cannot connect to the network. •• Check the network status.
Additional Information English Specifications Audio Section Multichannel power 75 W per channel, two channels driven @ 6 ohms, 20 Hz – 20 kHz, <0.
R-807 Network AV Receiver Video Section Television format NTSC/PAL Input level/impedance 1 Vp-p/75 ohms Output level/impedance 1 Vp-p/75 ohms Video frequency response (composite video) 10 Hz – 8 MHz (–3 dB) HDMI With 3 D and Deep Color General Specifications Power requirement AC 230 V/50 Hz Power consumption <0.5 W (standby), 280 W maximum Dimensions (W x H x D) 17.12" x 4.9" x 13" (435 mm x 125 mm x 331 mm) Weight 22.9 lb (10.
R-807 Network AV Receiver Récepteur réseau AV Receptor A/V con conexión de red Netzwerk-AV-Receiver Сетевой AV-ресивер 5707-00000-795-0S Printed in China Imprimé en Chine Impreso en China Gedruckt in China Отпечатано в Китае