O P E R A T I N G I N S T R U C T I O N S MASTER VOLUME AUDIO/VIDEO RECEIVER RD-6108 MAIN POWER REMOTE SENSOR ST TUNED TAPE M dB kHz MHz DTS ON/ DIGITAL Pro Logic THEATER HALL PRESET MEM TONE DIRECT ms SLEEP OFF INPUT SELECTOR STANDBY AUDIO VIDEO TAPE MON.
Introduction ENGLISH UNPACKING AND INSTALLATION Congratulations on Your Purchase! Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material.
FOR U.S.A AND CANADA ..............................120 V FOR OTHER COUNTRIES ................... 115 V/230 V FOR YOUR SAFETY FOR YOUR SAFETY Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only. Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch. Safety precaution with use of a polarized AC plug.
ENGLISH CONTENTS Introduction UNPACKING AND INSTALLATION ....................................................................................................... 2 READ THIS BEFORE OPERATING YOUR UNIT................................................................................... 3 System Connections ........................................................................................................................................ 5 Front Panel Controls ..............................................
Do not plug the AC input cord into the wall AC outlet until all connections are completed. Be sure to connect the white RCA pin cord to the L(left) and the red RCA pin cord to the R(right) jacks when making audio connections. Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. A 75 Ω outdoor FM antenna may be used to further improve the reception. Disconnect the indoor antenna before replacing it with the outdoor one.
ENGLISH ■ AC INPUT CORD ■ SUBWOOFER PRE OUT connection Plug this cord into a wall AC outlet. PRE OUT SUB WOOFER Powered subwoofer MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS,INC. US PAT. NO. 5,451,942, 5,956,674, 5,974,380, 5,978,762 AND OTHER WORLD-WIDE PATENTS ISSUED AND PENDING. "DTS" AND "DTS DIGITAL SURROUND" ARE REGISTERED TRADEMARKS OF DIGITAL THEATER SYSTEMS, INC. COPYRIGHT 1996, 2000 DIGITAL THEATER SYSTEMS, INC. ALL RIGHTS RESERVED. AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.
Front Panel Controls 6 CH DIRECT BUTTON ENGLISH REMOTE SENSOR AUDIO INPUT SELECTOR BUTTON TONE DIRECT BUTTON/INDICATOR VIDEO INPUT SELECTOR BUTTON TAPE MONITOR BUTTON DIGITAL INPUT BUTTON STANDBY BUTTON/ INDICATOR POWER SWITCH STEREO BUTTON MASTER VOLUME CONTROL KNOB MASTER VOLUME AUDIO/VIDEO RECEIVER RD-6108 MAIN POWER ST TUNED REMOTE SENSOR TAPE M dB kHz MHz DTS ON/ DIGITAL Pro Logic THEATER HALL PRESET MEM TONE DIRECT ms SLEEP OFF INPUT SELECTOR STANDBY VIDEO AUDIO SURROUND MODE
ENGLISH Remote Controls SLEEP BUTTON DISPLAY BUTTON POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 7 8 9 CD T.TONE 0 P.SCAN TUNER DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON POWER BUTTON INPUT SELECTOR BUTTONS NUMERIC(1~0) BUTTONS For selecting preset stations in tuner mode. TEST TONE BUTTON DSP MODE BUTTON DELAY TIME BUTTON AUTO BUTTON CHANNEL SELECTOR BUTTON CHANNEL LEVEL UP/DOWN(+/-) BUTTONS CH.
AUDIO/VIDEO RECEIVER RD-6108 ENGLISH REMOTE CONTROL OPERATION RANGE MASTER VOLUME MAIN POWER ST TUNED REMOTE SENSOR TAPE M dB kHz MHz DTS ON/ DIGITAL Pro Logic THEATER HALL PRESET MEM TONE DIRECT ms SLEEP OFF INPUT SELECTOR STANDBY VIDEO AUDIO TAPE MON.
Operations ENGLISH LISTENING TO A PROGRAM SOURCE Before operation Enter the standby mode. 3 MAIN POWER Select the desired input source. VIDEO1 INPUT SELECTOR POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 6 VIDEO3 4 ON/ OFF AUDIO VIDEO TAPE MON. 5 7 8 9 CD T.TONE 0 P.SCAN TUNER DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON CH. LEVEL The STANDBY indicator lights up.
4 7 Select the digital or analog input connected as desired. CINEMA EQ DIGITAL INPUTS Then “C-EQ ON” is displayed. Press it again to cancel, the “C-EQ OFF” is displayed. When the 6 CH DIRECT is selected as an input source, the cinema EQ function does not work.
ENGLISH Adjusting the tone(bass and treble) 10 11 Enter the tone mode. At the desired tone mode, adjust the tone as desired. ADJUST TONE MODE If the tone display disappears, start from the step 10 again. Notes: Extreme settings at high volume may damage your speakers. When the digital signals from DTS or Dolby Digital program sources are input in available surround mode, the tone cannot be adjusted and the tone direct function is automatically switched to ON.
This receiver incorporates a sophisticated Digital Signal Processor that allows you to create optimum sound quality and sound atmosphere in your personal Home Theater. Surround modes DTS Digital Surround DTS Digital Surround(also called simply DTS) is a multichannel digital signal format which can handle more amount of data than Dolby Digital, providing better audio quality. Though the number of audio channels is 5.
ENGLISH Delay time When the center speaker or the rear speakers is(are) closer to the listener than the front speakers, the sound from the center speaker or the rear speakers can arrive at the listener’s ears earlier than the sound from the front speakers. In this case, the imaging is not as sharp and stable as it could be.
Surround sound effect will not work properly if the signal passes through a graphic equalizer. Please refer to your equalizer operating instructions for guidance on switching off (or defeating) the equalizer. 1 Depending on the input digital signal format, select the desired decoding mode. POWER DISPLAY 1 AUTO 2 4 AUTO or 5 SLEEP VIDEO1 3 VIDEO2 6 VIDEO3 7 8 9 CD T.TONE 0 P.SCAN TUNER DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON CH.
ENGLISH 4 At the desired parameter, adjust it as desired. ADJUST 5 Note: In the Dolby Pro Logic II Customer mode, you cannot set both of the 7 kHz Low Pass Filter and Shelf Filter to ON simultaneously. If so, the filter set previously is automatically changed to OFF. If the parameter display disappears, start from the step 3 again. Adjusting the speaker settings 7 Adjust the settings of front, center ,rear speakers and subwoofer connected.
11 12 Select the desired channel. CHANNEL SELECTOR POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 7 8 9 CD TUNER 0 P.SCAN DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON T.TONE CH. SEL CH. LEVEL or ADJUST CH. LEVEL POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 7 8 9 CD T.TONE 0 P.SCAN TUNER DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON CH.
ENGLISH In Dolby Digital, Dolby Pro Logic II, Dolby Pro Logic or Dolby Virtual mode, adjusting delay times of the speakers 18 In case of Dolby Digital, Dolby Pro Logic II or Dolby Pro Logic mode, when the distances from the prime listening position to front left, center, front right, rear left and rear right speakers are same, the basic settings are as follows according to the surround modes; 17 D.TIME DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 7 8 9 CD T.TONE 0 P.
Auto tuning 1 2 Select the tuner. Select the desired band. BAND MHz AUDIO POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 7 8 9 CD TUNER 0 P.SCAN DSP MODE D.TIME ADJUST AUX AUTO CH. SEL MUTE T.MON T.TONE CH. LEVEL or 3 ENGLISH LISTENING TO RADIO BROADCASTS TUNER BAND FREQUENCY MASTER VOLUME Each time this button is pressed, the band is changed to FM or AM. When pressing the BAND button without selecting the TUNER, the tuner will be selected automatically.
ENGLISH 3 Select the desired preset number (1~30) and press the MEMORY/ENTER button. 4 MEMO/ENTER TUNING/PRESET Repeat the above steps 1 to 3 to memorize other stations. MEMORY BACKUP FUNCTION When using the NUMERIC buttons on the remote control. 3 Examples) For “3” : For “15” : For “30” : 1 within 2 seconds The following items, set before the receiver is turned off, are memorized. INPUT SELECTOR settings Surround mode settings Preset stations,etc.
The analog signals from the 6 CH DIRECT inputs as well as the digital signals from the coaxial or optical digital input can be heard but cannot be recorded. The volume and tone (bass, treble) settings have no effect on the recording signals. Recording with TAPE MONITOR 2 Select the desired input as a recording source except for TAPE MONITOR. 1 Start recording on the TAPE MONITOR. VIDEO1 AUDIO VIDEO POWER DISPLAY SLEEP VIDEO1 1 2 3 VIDEO2 4 5 6 VIDEO3 9 CD T.TONE 0 P.
ENGLISH 3 Start recording on the VIDEO 1. 4 Start play on the VIDEO 2 and the CD respectively. The audio signal from the CD and the video signal from the VIDEO 2 will be dubbed and you can enjoy them on the TV set and from the speakers. Note : Be sure to observe the order of the above steps 1 and 2.
If a fault occurs, run through the table below before taking your receiver for repair. If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult your dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty. PROBLEM POSSIBLE CAUSE REMEDY No power The AC input cord is disconnected. Poor connection at AC wall outlet or the outlet is inactive. Connect the cord securely.
Specifications ENGLISH AMPLIFIER SECTION Power output, stereo mode, 6 Ω, THD 0.7%, 40 Hz~20 kHz .................................................................................. 2×100 W Total harmonic distortion, 6 Ω, 100 W, 1 kHz ............................................................................................................... 0.09% Intermodulation distortion 60 Hz : 7 kHz= 4 : 1 SMPTE, 6 Ω, 100 W ...............................................................................................
O P E R A T I N G I N S T R U C T I O N S RD-6108 AUDIO/VIDEO RECEIVER 5707-04735-008-0