HK560M User’s Manual Document version 1.0 QingDao Hisense Intelligent Commercial System Co.,Ltd.
Safety Notices Before Installation or Use ☆ It is required grounded well and the supply voltage shall be stable, and you must confirm that the voltage of the outlet provides shall be in line with the voltage marked on the label of the unit. ☆ Be sure not to sprinkle any liquid or fall any object into the unit. ☆ Be sure not to keep heavy, strenuous movement, shake & heavy strike away from the POS. ☆ Do not switch on or off the host frequently, because it is easy to result in damage on the machine.
Warning: 1. Absolute Ratings of Environment： Operating Temperature：0～40℃ Operating Humidity：10%～85%RH Storage Temperature：-10～50℃ Storage Humidity：10%～90%RH 2. Main plug on the power supply was used as disconnected device. The socket -outlet shall be installed near the equipment and shall be easily accessible 3. If any damage to the power supply or the equipment, please contact local service person for help. 4. Static may damage to the integrated circuit in the host machine. 5.
I/O Ports Power LAN 1 * RJ-45 (100M/1000Mbps Gigabit LAN) HDMI 1*HDMI Port Audio 1 * Line-out Cash Drawer 1 * RJ-11 for cash drawer Power Adapter Adapter (DC 24V, 2.5A)(Standard) Adapter (DC 24V, 5A) (optional) VFD 2*20 characters Second Display 15.6 inch (touch/non-touch) Peripheral 12.5 inch(touch/non-touch) 10.
3).Remove the two connectors shown in the picture and protect them with the tape according to the picture shows (to prevent the connector from being pulled out in the process of dismantling and threading); 4).Rotate the main screen and the secondary screen : to the vertical angle, remove the three screws of the main screen hinge and the second screen hinge respectively, and carefully pass the screen line through the line hole. Separate the main and auxiliary screen from the base respectively.
5).Remove the hinges of the host: Remove four screws according to the picture shows. Remove the hinges of the host and the hinges cover of the host separately. 6).Remove the extended interface cover: pull the expanded interface cover outward at the notch according to the picture shows, and remove it. 7. remove the hard drive, unscrew the hard drive fixing screw, then remove the hard drive as arrow direction show in the picture below. 8.
5. Environmental requirements Type State Voltage Environmental AC 100V-240V 50-60Hz Bipolar Temperature 5℃ - 40℃ Optimal 40% - 90% 6.
Main Flip Angle 0-45°，Second screen Flip Angle 0-30° High position +printer，Length×Width×Height：405*250*420 Self-service，Length×Width×Height：230*250*450 7. Open the box and check. 1) Before opening the box, check whether the box is in good condition, and whether there is any obvious damage. 2) The equipment must be installed by technical service person or distributors.
When swiping the card, the machine should be placed on a hard horizontal plane. Please swipe the magnetic strip of the magnetic strip card inward from the swipe slot. The process of card swiping should be smooth and uniform. 4) Contactless card operation： Contactless card induction zone is located behind the right side of the host (with the contactless mark printed). When need read contactless card, please place the card above the induction zone. 8.
2) Load and change paper introduction a. Press the open button to open the paper bin cover, as shown below. If there are paper tubes in the paper warehouse, please take them out. b. Put the paper roll into the paper bin, pay attention to the correct direction of the paper roll. c.
d. Remove excess paper toward the side of the paper cut. Paper rolling 1) Requirements of the thermal paper： Type：Thermal paper Width of paper：57.5±0.5mm / 79.5±0.5mm Outside Diameter of paper roll：Max 83mm Thickness of Thermal Paper：0.056 ~ 0.13mm 2) Recommendation of thermal Paper Model： Type FD210,PD150R,PD160R Manufacture OJI Paper CO.
A. Please use the recommended paper roll or the same quality paper roll. The use of other types of paper roll may affect the printing effect and the life of the printing head. B. If the paper roll is contaminated by chemicals or oil, the contaminated part of the paper roll may fade or the printing effect is not clear. C. Do not scratch the thermal sensitive layer of the paper roll with sharp objects, which may make the printing effect unclear. D.
FCC Warning Statement This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
