User Manual

ManualsBrandsSHIMPO ManualsToolsDT-315AEB

LIMITED EXPRESS WARRANTY: Shimpo Instruments warrants, to the original purchaser of new products only, that this product shall be free from defects in workmanship and materials under normal use

and proper maintenance for one year from the date of original purchase. This warranty shall not be ef fective if the product has been subject to overload, misuse, negligence, or accident, or if the product has been

repaired or altered outside of Shimpo Instruments’s authorized control in any respect which in Shimpo Instruments’s judgment, adversely affects its condition or operation.

DISCLAIMER OF ALL OTHER WARRANTIES: The foregoing warranty constitutes the SOLE AND EXCLUSIVE WARRANTY, and Shimpo Instruments hereby disclaims all other warranties, expressed,

statutory or implied, applicable to the product, including, but not limited to all implied warranties of merchantability and fitness.

LIMITATION OF REMEDY: Under this warranty, Shimpo Instruments’s SOLE OBLIGATION SHALL BE TO REPAIR OR REPLACE the defective product or part, at Shimpo Instruments’ option. Shimpo

Instruments reserves the right to satisfy warranty obligation in full by reimbursing Buyer for all payments made to Shimpo Instruments, whereupon, title shall pass to Shimpo Instruments upon acceptance of return

goods. To obtain warranty service, Purchaser must obtain Shimpo Instruments’s authorization before returning the product, properly repackaged, freight pre-paid to Shimpo Instruments.

INDEMNIFICATION & LIMITATION OF DAMAGES: Buyer agrees to indemnify and hold Shimpo Instruments harmless from and against all claims and damages imposed upon or incurred arising, directly

or indirectly, from Buyer’s failure to perform or satisfy any of the terms described herein. In no event shall Shimpo Instruments be liable for injuries of any nature involving the product, including incidental or

consequential damages to person or property, any economic loss or loss of use.

MERGER CLAUSE: Any statements made by the Seller’s representative do not constitute warranties except to the extent that they also appear in writing. This writing constitutes the entire and final expression

of the parties’ agreement.

Warranty

Dimensions & Specifications

Troubleshooting

FPM reading is displayed but unit is not flashing:

• Flash tube may need to be replaced (see "Flash Tube

Replacement" section)

Stroboscope is in external trigger mode, no flash:

• Check flash tube. Replace if necessary

• Check for damaged wiring and/or loose pin connections

STROBOSCOPE SPECIFICATIONS

ModelModel

Model

DTDT

-315AEB-315AEB

-315AEB

INTERNAL MODEINTERNAL MODE

INTERNAL MODE

Flashing RFlashing R

Flashing R

angeange

ange 40.0 - 35,000 FPM (flashes per minute)

AccuracyAccuracy

Accuracy ±0.01% of reading

esolutionesolution

esolution 0.1 FPM: 40.0 - 4,999.9 FPM

0.2 FPM: 5,000 - 7,999.8 FPM

0.5 FPM: 8,000 - 9,999.5 FPM

1 FPM: 10,000 - 35,000 FPM

Phase ShifPhase Shif

Phase Shif

t Use +/- push buttons (360° in 6 seconds)

Display Update TimeDisplay Update Time

Display Update Time 0.2 sec approx.

Output SignalOutput Signal

Output Signal Synchronous, 400 msec. Pulse output, 0 to +12 VDC amplitude(approx.), 4.7 KΩ impedance

ate Multiplier/Dividerate Multiplier/Divider

ate Multiplier/Divider Multiply by 2, divide by 2

EXTERNAL MODEEXTERNAL MODE

EXTERNAL MODE

Flashing RFlashing R

Flashing R

angeange

ange 0.0 - 35,000 FPM

AccuracyAccuracy

Accuracy ±0.01% ±1 digit

Phase ShifPhase Shif

Phase Shif

t 0 - 359° with 1° resolution

Delay TimeDelay Time

Delay Time 0 - 2,000 msec from 40 - 10,000 FPM

ExterExter

Exter

nal Tnal T

nal T

rigger Input Signalrigger Input Signal

rigger Input Signal LO level: 0 - 0.8 VDC, HI level: 2.5 - 12 VDC or open collector (NPN), pulse width 50 msec min.

Input ImpedanceInput Impedance

Input Impedance 4.7 KΩ at 12 V / 6.8 KΩ at 0 V

GENERGENER

GENER

ALAL

DisplayDisplay

Display 5 digits, 0.4" (10 mm) high, LED

Flash TFlash T

Flash T

ube Pube P

ube P

ower/Lifeower/Life

ower/Life Xenon, 10 W max. (100 million flashes)

Flash DurationFlash Duration

Flash Duration 10 - 40 msec

Sensor PSensor P

Sensor P

ower Supplyower Supply

ower Supply 12 VDC (40 mA)

Low BatterLow Batter

Low Batter

y Indicatory Indicator

y Indicator Display shows all L’s

ower Rower R

ower R

equirementequirement

equirement Internal Battery Pack

Operating TOperating T

Operating T

emperature Remperature R

emperature R

angeange

ange 32° - 104°F ( 0 - 40°C )

eighteight

eight 2.5 lb (1.1 kg)

DimensionsDimensions

Dimensions 7.28"L x 4.72"W x 4.72"H (185 mm x 120 mm x 120 mm)

arar

rantyranty

ranty 1 year

Standard AccessoriesStandard Accessories

Standard Accessories External battery pack with charger

Optional AccessoriesOptional Accessories

Optional Accessories Carrying case

Stroboscope is in internal trigger mode, no flash:

• Check flash tube. Replace if necessary

• Check for damaged wiring and/or loose pin connections