INTRODUCTION ) CONTENTS This Shindig 577570 saw was Page designed and built to deliver superior ik . performance and reliability without Attention Statements 1 comprise to quality, comfort, Nomenclature. 2 safety, of durability Specifications 3 Hinduism high performance . engines represent the leading edge of Softy Information -4 Exercycle engine technology, and deliver Kickback Satiety B exceptionally high power at . . rear ably low displacement and Kickback Safety Precautions 7 weight.
ATTENTION STATEMENTS This manual contains special “attention statements” surrounded by Coxes and preceded by the triangular Attention Symbol WARNING! A A statement preceded by the word “WARNING” contains information that showed be acted upon to prevent serious bodily injury CAUTION! A A statement preceded by the word “CAUTION" contains information that should be acted upon to prevent damaging your saw Additional attrition statements that are not preceded by the Attention Symbol are: IMPORTANT! A statement p
, or not performing required penance services, placental parts used for required 5, consequential pacts used for acquired e serviettes, section fees Hat do not (6) diagnosis and 1+ sl i eligible warranty service being o1 foamed, and () any Lon authorized replacement part, ot nonfunctional of weatherized parts due to nse f non authorized parts MAINTENANCE AN REPAIR REQUIREMENTS Vau are responsible for the proper vse and maintenance of the engine You should ) receipts and maintenance records sng the performan
SAFETY PRECAUTIONS A WARRING! NOTE: These safety precautions are intended primarily for the consumer or occasional user. When using this n saw for logging purposes, refer to GFR Section 1910. 266 (5); 25.1 of the American National Safety Standard; Requirements for Pulpwood Logging ANSI and any applicable state safety codes (e Read this manual carefully before operating your new Shindig chain saw. The following safety precautions should be observed by all users of chain saws: 1.
Symptom — i~ | Engine stops abruptly L sine difficult to shut off TROUBLESHOOTING Possible cause Clogged ai cleaner Clogged fuel dither Chain brake engaged Carburetor mixture (00 rich oz too lean Idle speed set too low Switch turned off Fuel tank empty Clogged fuel filter Water in the fuel Shorted spark plug ox loose terminal Ignition failure Piston seizure, Ground (stop) quite is disconnected, or switch is defective Overheating due 1o incorrect spark plug, Overheated engine.
KICKBACK SAFETY L This saw is equipped with the following safety equipment: 1. Manual chain brake 2. Low kick chain. 3. Guard-tip bar B Activating the chain brake tightens a brake band around the chain jive mechanism, stopping all chain rotation The chain brake can be activated manually, and is also designed to activate when kickback energy forces the brake lever against the operator’s left hand.
TROUBLESHOOTING Hat o check Dress the engine crank? _ESy Good compression? ey Douse the tank contain fresh fuel of the props grade? R Is fuel reaching the cylinder and combustion chamber? TIs these spark at the spark plug quite terminal? s Possible cause Faulty recoil starer 885 o Fluid in the crankcase Internal damage Loose spark plug 5| Excess wear on cylinder, piston, Tings. Stale o1 contaminated fuel mixture Cheek for clogged fuel filter and/or vent.
MOUNTING GUIDE BAR AND SAW CHAIN 1 Remove two nuts; clutch cover and spacer 2 Install guide bar To install guide bar, insert the plate (A) and giddy bar slot over bar studs 8. Fit saw chain first from sprocket rim side, then font guide bar groove toward bar tip Check if saw chain is properly fitted into rim. 4 Inst ail clutch cover and secure it temporarily with 2 nuts.
SAW CHAIN SHARPENING 1. B assignation— ‘ Tie strap wile rivets Tio Gutter fight hens 3 % e Driver fink 2. Functions The depth gauge controls depth or amount of cut for each tooth Eight made left cotters both should always be sharpened to uniform angle and depth « Pride links.and saw chain together function o discharge sawdust. 3. Points sharpshooting Sharpen all cutters and align right and left cutter angles to nest these specifications: 4. Fow to Sharpen— a.
FILLING FUEL AND CHAIN OIL, 1.
ROUTINE MAINTENANCE MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISH OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A DEALER OR SERVICE CENTER AUTHORIZED BY BRAINWASHING KOOKY CO, LTD. THE USE OF PARTS THAT ARE NOT EQUIVALENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY PATRIOT THE EFFECTIVENESS.
3) Pull recoil starter rope while holding the chain saw firmly and placing your right foot into rear handle as shown in the illustration.
CUTTING 1. Before Tasting Understand safety procedures. b. Clear a safe work area « One should wear safety helmet, protective wear for hands and feet, and close fitting but comfortable clothes <. When moving from place o place, stop engine for safety. « Always keep saw chain pensioned properly and inspect often t Check fot loose bolts and nuts before use.
4. High Speed (H) Adjustment— (1} EPA only High speed mixture setting is factory-set, and cannot be adjusted in the field (2) EMC only No adjustment is necessary when the saw s new. After approximately 10 hours use, rotate the H-needle clockwise to | teens (£ 1/4 turns) CAUTION! A 1. Do not ripsaw at full throttle with NoDoz If vun in this condition, major engine damage can occur 2. Do not exceed 13,006 1pm CAUTION Do not adjust B-needle ai 34 twn or less, If tun in condition, seize can grocer.