Operator’s Manual EB770 RT Power Blower The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Read and understand all provided literature before use. Failure to do so could result in serious injury. This product complies with CAN ICES-2/NMB-2.
TABLE OF CONTENTS EB770RT TABLE OF CONTENTS Table of Contents ........................................................................................... 2 Introduction ..................................................................................................... 3 Servicing Information ...................................................................................... 3 Parts/Serial Number ................................................................................ 3 Service ...............
EB770RT INTRODUCTION INTRODUCTION Specifications, descriptions and illustrative material in this literature are as accurate as known at the time of publication, but are subject to change without notice. Illustrations may include optional equipment and accessories, and may not include all standard equipment. Read and understand all provided literature. Literature contains specifications and information for safety, operation, maintenance, storage and assembly specific to this product.
SAFETY EB770RT Service Service of this product during the warranty period must be performed by an Authorized SHINDAIWA Service Dealer. For the name and address of the Authorized SHINDAIWA Service Dealer nearest you, ask your retailer or call: 1-877-986-7783. Dealer information is also available on WWW.SHINDAIWA-USA.COM. When presenting your unit for Warranty service/repairs, proof of purchase is required.
EB770RT SAFETY The safety alert symbol accompanied by the word “WARNING” calls attention to an act or condition which CAN lead to serious personal injury or death if not avoided. The safety alert symbol accompanied by the word “CAUTION” calls attention to an act or condition which may lead to minor or moderate personal injury if not avoided. The enclosed message provides information necessary for the protection of the unit.
SAFETY Symbol EB770RT Description Symbol Description Hot Surface Fuel and Oil Mixture Idle speed Fast speed Finger severing Primer Bulb DO NOT Allow Flames or Sparks Near Fuel Ignition ON / OFF DO NOT Smoke Near Fuel Choke Control “COLD START” Position (Choke Closed) Choke Control “RUN” Position (Choke Open) Wear Slip Resistant Footwear Beware of thrown objects Keep Bystanders and Helpers Away 15 m (50 ft.).
EB770RT SAFETY Personal Condition and Safety Equipment Cancer and Reproductive Harm www.P65Warnings.ca.gov The muffler or catalytic muffler and surrounding cover may become extremely hot. Always keep clear of exhaust and muffler area, otherwise serious personal injury may occur. Users of this product risk injury to themselves and others if the unit is used improperly and/or safety precautions are not followed. Proper clothing and safety gear must be worn when operating unit.
SAFETY EB770RT Eye Protection ◆ ◆ Eye protection that meets ANSI Z87.1 or CE requirements must be worn whenever you operate the unit. For additional safety, a full-face shield may be worn over safety glasses or goggles to provide protection from sharp branches or flying debris. Hand Protection Wear sturdy, no-slip, rubber work gloves to improve your grip on the handles.
EB770RT SAFETY Heavy protective clothing can increase operator fatigue, which may lead to heat stroke. Schedule heavy work for early morning or late afternoon hours when temperatures are cooler. The components of this machine generate an electromagnetic field during operation, which may interfere with some pacemakers. To reduce the risk of serious or fatal injury, persons with pacemakers should consult with their physician and the pacemaker manufacturer before operating this machine.
SAFETY EB770RT Repetitive Stress Injuries (RSI) It is believed that overusing the muscles and tendons of the fingers, hands, arms, and shoulders may cause soreness, swelling, numbness, weakness, and extreme pain in those areas. Certain repetitive hand activities may put you at a high risk for developing a Repetitive Stress Injury (RSI). An extreme RSI condition is Carpal Tunnel Syndrome (CTS), which could occur when your wrist swells and squeezes a vital nerve that runs through the area.
EB770RT SAFETY Do not operate this product indoors or in inadequately ventilated areas. Engine exhaust contains poisonous emissions and can cause serious injury or death. Read the Manual • Provide all users of this equipment with literature for instructions on safe operation. Clear the Work Area • Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders, and pets outside a 15 m (50 ft.) radius; outside the 15 m (50 ft.
SAFETY EB770RT Equipment Use only approved attachments. Serious injury may result from the use of a non-approved attachment combination. ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. Read and comply with all safety instructions listed in this manual. ◆ Check unit for loose/missing nuts, bolts, and screws. Tighten and/or replace as needed. ◆ Do not use blower if any part is missing or damaged.
EB770RT EMISSION CONTROL EMISSION CONTROL (EXHAUST & EVAPORATIVE) CARB And EPA Emissions Control Information The emission control system for the engine is EM (engine modification) and, if the second to last character of the Engine Family on the Emission Control Information label (sample below) is “B”, “C”, “K”, or “T”, the emission control system is EM and TWC (3way catalyst). The fuel tank/fuel line emission control system is EVAP (evaporative emissions).
DESCRIPTION EB770RT DESCRIPTION Locate the safety decal(s) on your unit. Make sure the decal(s) is legible and that you understand and follow the instructions on it. If a decal cannot be read, a new one can be ordered from your dealer. The safety decal is for example only. Your label may appear slightly different.
EB770RT 1. Spark Plug 2. Safety Decal 3. Spark Arrestor - Catalytic Muffler / Muffler 4. Fuel Tank 5. Fuel Tank Cap 6. Recoil Starter Handle 7. Air Cleaner 8. Choke 9. Purge Bulb 10. Shoulder Harness 11. Handle 12. Throttle Position Lever 13. Locking Knob 14. Blower Pipes 15. Flexible Pipe 16.
CONTENTS EB770RT CONTENTS The SHINDAIWA product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions, some assembly may be necessary. After opening the carton, check for damage. Immediately notify your retailer or SHINDAIWA Dealer of damaged or missing parts. Use the contents list to check for missing parts.
EB770RT 2. ASSEMBLY Insert anti-static wire (I) through flexible pipe (B). Note: A light lubricant may be used to ease assembly of flexible pipe to blower elbow. 3. Assemble flexible pipe to elbow (D) on blower. Position clamp with cable guide loop (G) on outside of flexible pipe and tighten clamp. C D G I B Note: Hang handle freely from blower to assure throttle cable is not twisted before installing handle (E). 4. 5. Position throttle cable along the outside of elbow.
OPERATION 8. EB770RT Move handle (E) to desired position. Tighten knob (H) hand tight. E C H 9. Assemble straight pipe (J) onto swivel pipe (C), until you feel light resistance. Do not force connection. Hold swivel pipe and turn straight pipe clockwise, engaging positive locking channels, until connection is firm. Do not force connection. 10. Assemble straight pipe with decal (K) to straight pipe as in step 9. J C K Note: Blower use will eventually loosen pipe connections.
EB770RT OPERATION Operation of this equipment may create sparks that can start fires around dry vegetation. This unit is equipped with a spark arrestor to prevent discharge of hot particles from the engine. Contact local fire authorities for laws or regulations regarding fire prevention requirements. Engine exhaust IS HOT, and contains Carbon Monoxide (CO), a poison gas. Breathing CO can cause unconsciousness, serious injury, or death. Exhaust can cause serious burns.
OPERATION EB770RT Fuel Requirements Gasoline - Use 89 Octane [R+M/2] (mid grade or higher) gasoline known to be good quality. Gasoline may contain up to 10% Ethanol (grain alcohol) or 15% MTBE (methyl tertiary-butyl ether). Gasoline containing methanol (wood alcohol) is NOT approved. Use of ECHO branded fuel is recommended to extend engine life in all air-cooled 2-stroke and 2/4-stroke hybrid engines.
EB770RT ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ ◆ OPERATION Use an approved fuel container. DO NOT smoke near fuel. DO NOT allow flames or sparks near fuel. Fuel tanks/cans may be under pressure. Always loosen fuel caps slowly allowing pressure to equalize. NEVER refuel a unit when the engine is HOT or RUNNING! DO NOT fill fuel tanks indoors. ALWAYS fill fuel tanks outdoors over bare ground. DO NOT overfill fuel tank. Wipe up spills immediately. Securely tighten fuel tank cap and close fuel container after refueling.
OPERATION EB770RT After use • Empty the fuel tank prior to storing the unit. Return unused fuel to an approved fuel storage container. Storage - Fuel storage laws vary by locality. Contact your local government for the laws affecting your area. As a precaution, store fuel in an approved, airtight container. Store in a well-ventilated, unoccupied building, away from sparks and flames. Stored fuel ages.
EB770RT 2. Move choke (C) UP to COLD START ( ) position. 3. Pump purge bulb (D) until fuel is visible. Pump bulb an additional 4 or 5 times. 4. Pull recoil starter handle (E) until engine fires, or a maximum of 5 pulls 5. After engine fires (or 5 pulls), move choke lever back to RUN ( ) position, then pull starter handle/rope until engine starts and runs. Allow unit to warm up at idle for several minutes.
OPERATION 2. 3. EB770RT Pump purge bulb (D) until fuel is visible. Pump bulb an additional 4 or 5 times. Pull recoil starter handle (E) and engine should start. Do not use choke (C) Note: If engine does not start after 5 pulls, use cold start procedures. E C D Stopping Engine 1. Throttle Position Lever Release throttle trigger. Move Throttle Position Lever (A) forward to idle position and allow engine to return to idle before shutting off engine. 2.
EB770RT OPERATION Always wear safety glasses, hearing protection and a face filter mask or serious personal injury may result. Do not point the blower pipe in the direction of people or pets. Use reduced speed only when performing light-duty tasks or to comply with local noise regulations. Continuous low speed operation may allow fuel/oil residue to build-up on the piston and cause rapid build-up of carbon on the spark arrestor screen, resulting in overheating and engine damage.
OPERATION EB770RT Note: Never use a higher speed setting than necessary to perform a task. Remember, the higher the engine speed, the louder the blower noise. For Operator Comfort in Cold Weather Operation: This product should not be used in temperatures below 15° F (9° C) otherwise damage to the fuel lines may occur. 1. Remove back cushion (A) from frame. A 2. Install intake cover (B) on frame over air intake. 3. Install back cushion (A) to frame over intake cover.
EB770RT MAINTENANCE MAINTENANCE Moving parts can amputate fingers or cause severe injuries. Keep hands, clothing and loose objects away from all openings. Always stop engine, disconnect spark plug, and make sure all moving parts have come to a complete stop before removing obstructions, clearing debris, or servicing unit. Allow unit to cool before performing service. Wear gloves to protect hands from sharp edges and hot surfaces.
MAINTENANCE EB770RT Maintenance Intervals COMPONENT/SYSTEM MAINTENANCE PROCEDURE REQ’D SKILL LEVEL Daily or Before Use Air Filter Inspect/Clean * 1 Choke Shutter Inspect/Clean * 1 Fuel System Inspect 1 1 Cooling System Inspect/Clean 2 Recoil Starter Rope Inspect/Clean * 1 Screws/Nuts/Bolts Inspect/Tighten/Replace * 1 Inspect 1 1 Air Filter Replace * 1 Fuel Filter Inspect * 1 Fuel Cap Gasket Inspect * 1 Spark Plug Inspect/Clean/Replace * 1 Muffler Spark Arrestor Inspect/
EB770RT MAINTENANCE 1. Close choke (COLD START( ) position). This prevents dirt from entering the carburetor throat when the air filter is removed. Brush accumulated dirt from air cleaner area. 2. Remove air filter cover, air filter, retainer, and foam pre-filter. Brush dirt from inside cover. Foam Pre-Filter: • Clean foam filter (A) in water/ detergent solution and rinse with clean water. • Wrap the filter in a clean, dry cloth and squeeze (do not wring) dry. Allow to dry completely before reuse.
MAINTENANCE 1. Use a clean rag to remove loose dirt from around fuel cap and empty fuel tank. 2. Pull the fuel filter from the tank. EB770RT Do not damage fuel line while removing fuel filter from tank. 3. Remove the filter from the line and install the new filter. Note: Federal EPA regulations require all model year 2012 and later gasoline powered engines produced for sale in the United States to be equipped with a special low permeation fuel supply hose between the carburetor and fuel tank.
EB770RT MAINTENANCE Cooling System Level 2. To maintain proper engine operating temperatures, cooling air must pass freely through the cylinder fin area. This flow of air carries combustion heat away from the engine. Overheating and engine seizure can occur when: • Air intakes are blocked, preventing cooling air from reaching the cylinder. • Dust and grass build up on the outside of the cylinder. This build up insulates the engine and prevents the heat from leaving.
MAINTENANCE 4. EB770RT Clean cylinder fins (A) to allow cooling air to pass freely. 5. Install engine cover. 6. Install air filter cover. 7. Connect spark plug lead. A Exhaust System Spark Arrestor Screen Level 2. Parts Required: Spark Arrestor Screen, Gasket Carbon deposits in muffler will cause a drop in engine output and overheating. Spark arrestor screen must be checked periodically. 1. Disconnect spark plug lead from spark plug 2.
EB770RT 1. Remove spark plug lead from spark plug, and remove engine cover. 2. Place piston at top dead center. Remove muffler (A) and muffler gasket (B). 3. Use a wood or plastic scraping tool to clean deposits from cylinder exhaust port. MAINTENANCE B A Never use a metal tool to scrape carbon from the exhaust port. Do not scratch the cylinder or piston when cleaning the exhaust port. Do not allow carbon particles to enter the cylinder. 4. Inspect muffler gasket, and replace if damaged. 5.
MAINTENANCE EB770RT If the engine is adjusted for operation above 1,100 feet ASL, the carburetor must be re-adjusted when operating the engine below 1,100 feet ASL, otherwise severe engine damage may result. Level 2. Note: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized ECHO dealer.
EB770RT TROUBLESHOOTING 1. Loosen handle adjustment knob (C) and tilt Tube Throttle handle forward to expose Adjustment Screw (D). 2. Turn Adjustment Screw until Throttle Trigger free play is 4 - 6 mm (3/16-1/4 in.). 3. After adjustment, squeeze and release Throttle Trigger several times to verify Carburetor Throttle Shaft has full range of movement from idle to wide open throttle positions. 4-6 mm C D C TROUBLESHOOTING Fuel vapors are extremely flammable and may cause fire and/or explosion.
TROUBLESHOOTING EB770RT ENGINE PROBLEM TROUBLESHOOTING CHART Problem Check Status Cause No fuel at cylinder Carburetor Remedy See your dealer OPEN choke Fuel at cylinder Muffler wet with fuel See your dealer Move ignition Ignition at STOP position away from STOP position.
EB770RT STORAGE STORAGE During operation the muffler or catalytic muffler and surrounding cover become hot. Always keep exhaust area clear of flammable debris during transportation or when storing, otherwise serious property damage or personal injury may result. Long Term Storage (Over 30 Days) Do not store your unit for a prolonged period of time (30 days or longer) without performing protective storage maintenance which includes the following: 1.
SPECIFICATIONS EB770RT SPECIFICATIONS MODEL EB770 RT Length 1520 mm (59.8 in.) (with blower pipes) Width 525 mm (20.7 in.) Height 475 mm (18.7 in.) Weight (dry) 11 kg (24.3 lb.) (with blower pipes) Engine Type Air cooled, two-stroke, single cylinder gasoline engine Bore 48.0 mm (1.9 in.) Stroke 35.0 mm (1.4 in.) Displacement 63.3 cm3 (3.
EB770RT NOTES NOTES X7531127000 © 10/19 ECHO Incorporated 39
PRODUCT REGISTRATION EB770RT PRODUCT REGISTRATION Thank you for choosing Shindaiwa Power Equipment Please go to http://www.shindaiwa-usa.com to register your new product online. It's FAST and EASY! NOTE: your information will never be sold or misused by ECHO, Inc. Registering your purchase enables us to contact you in the unlikely event of a service update or product recall, and verifies your ownership for warranty consideration.
EB770RT PRODUCT REGISTRATION X7531127000 41 © 10/19 ECHO Incorporated
NOTES EB770RT NOTES 42 X7531127000 © 10/19 ECHO Incorporated
EB770RT NOTES X7531127000 43 © 10/19 ECHO Incorporated
P52115001001/P52115999999 ECHO INCORPORATED 400 Oakwood Road Lake Zurich, IL 60047 www.shindaiwa-usa.