Shindaiwa OWNER’S/OPERATOR’S MANUAL MULTIPURPOSE TILLER/ CULTIVATOR TOOL Model: 80265 WARNING! Part Number 80274 Rev. 02/10 Minimize the risk of injury to yourself and others! Read this manual and familiarize yourself with the contents. Always wear eye and hearing protection when operating this unit.
Introduction The Shindaiwa Multipurpose Tiller/Cultivator Tool is designed and built to deliver superior performance and reliability without compromise to quality, comfort, safety or durability. As an owner/operator, you’ll soon discover for yourself why Shindaiwa is simply in a class by itself! IMPORTANT! The information contained in these instructions describes units available at the time of publication. Echo Inc.
General Safety Instructions Work Safely This machine operates at very high speeds and has the potential to do serious damage if misused, abused or mishandled. To reduce the risk of injury, you must maintain control at all times, and observe all safety precautions during operation. Never permit a person without training or instruction to operate this machine! WARNING! WARNING! Never make unauthorized attachment installations. Stay Alert You must be physically and mentally fit to operate this unit safely.
The Properly Equipped Operator Always wear appropriate hearing protection. Always wear eye and hearing protection. Shindaiwa recommends wearing a face shield as additional face and eye protection. Wear nonslip heavy-duty work gloves to improve your grip on the handle. Wear snug-fitting clothes that also permit freedom of movement. NEVER wear shorts! Always operate with both hands firmly gripping the unit. Keep a proper footing and do not overreach—maintain your balance at all times during operation.
Product Description Multipurpose Tiller/ Cultivator Tool 80265 Outer Tube Gearcase Tines Debris Shield Using the illustration as a guide, familiarize yourself with your machine and its various components. Understanding your machine helps ensure top performance, long service life and safer operation. WARNING! Do not make unauthorized modifications or alterations to any of these units or their components.
Assembly Prior to assembly Before assembling, make sure you have all the components required for a complete unit: ■■Outer Tube/Mainshaft Assembly ■■Tiller/Cultivator Tool Assembly ■■Kit containing hardware, owner/operator's manual, and a 5 mm hex key. Carefully inspect all components for damage. IMPORTANT! The terms “left”, “left-hand”, and “LH”; “right”, “right-hand”, and “RH”; “front” and “rear” refer to directions as viewed by the operator during normal operation.
Assembly Assembling tube sections 1. Place powerhead/lower tube assembly on a clean, flat surface so that both assemblies fit end to end. The powerhead/lower tube assembly should be facing positioned with the locking hole in the tube end facing up. Assembling tube sections Latch protector (extended) Latch Lower tube assembly Coupler screw knob Locking hole CAUTION! Keep the open ends of the tubes clean and free of debris! 2.
Operating Checking Unit Condition NEVER operate the unit with the protective devices (ignition switch, etc.) removed! ALWAYS make sure the tool attachment is properly installed and firmly tightened before operation. Use only authorized Shindaiwa parts and accessories with your Shindaiwa Multipurpose Tool. Do not make modifications to your machine without the written approval of Shindaiwa. NEVER use a cracked or warped tine: replace it with a serviceable one.
Maintenance IMPORTANT! For detailed maintenance information about your unit, consult the owner's manual that was provided with it. If it has been lost or misplaced, contact Shindaiwa for a replacement. NOTE Using non-standard replacement parts could invalidate your Shindaiwa warranty. Daily Maintenance Prior to each work day, perform the following: ■■Remove all dirt and debris from the engine, check the cooling fins and air cleaner for clogging, and clean as necessary.
Troubleshooting Guide What To Check Tines rotates at engine idle. Excessive vibration. ADDITIONAL PROBLEMS Possible Cause Remedy Engine idle too high. Check Multipurpose Engine manual for correct idle speed and adjustment procedure. Broken clutch spring or worn clutch spring boss. Replace spring/shoes as required, check idle speed. Loose attachment holder. Inspect and re-tighten holders securely. Warped or damaged attachment. Inspect and replace attachment as required. Loose gearcase.
SHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010 ECHO, INC'S RESPONSIBILITY ECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC.
PURCHASED REPAIR PARTS AND ACCESSORIES • 90-day all applications ATTENTION ENGINE POWERED PRODUCT OWNERS This Shindaiwa engine powered product is a quality-engineered unit which has been manufactured to exact tolerances to provide superior performance. To help ensure the performance of the unit, it is required to use engine oil which meets the ISO-L-EGD Standard per ISO/CD 13738 and JASO M345/FD Standards.
NOTES 13
NOTES 14
NOTES 15
Servicing Information Parts/Serial Number Genuine Shindaiwa Parts and Assemblies for your Shindaiwa products are available only from an Authorized Shindaiwa Dealer. When you do need to buy parts always have the Model Number, Type and Serial Number of the unit with you. You can find these numbers on the engine. For future reference, write them in the space provided below. Model No. _____________ Type _________SN.