M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5544LCM 4x4 AUDIO-VIDEO MATRIX SWITCHER 4x4 AUDIO-VIDEO MATRIX SWITCHER Composite Video-Stereo Audio Matrix Switcher Series Thank you for purchasing the SB-5544LCM 4x4 Composite Video-Audio Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 4x4 Composite Video and Audio Matrix Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 FEATURES & SPECIFICATIONS ..................................... 2 FRONT PANEL ................................................................. 3 BACK PANEL .................................................................... 6 REMOTE CONTROL ....................................................... 7 REMOTE PROTOCOL COMMANDS ................................ 8 IR EXTENDER ..............
FEATURES & SPECIFICATIONS FEATURES • • • • • • • Support 4x Inputs To 4x Outputs Matrix Switcher. Video Audio signals support Composite Video and Stereo Audio (AR/AL) High Bandwidth Video 450MHz each Composite Video ports. Support IR remote and IR External, front panel and RS-232 serial interface protocol Controls. Compatible NTSC or PAL TV Video systems. RS-232 control via a PC Drive compatible PC win-98/2000/XP.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 4 LED illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show ”0” indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 4. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9. FUNCTION KEY - OFF Disables (mute) video to selected channels.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - MEMORY The system will show store presets, up to a total of 8. Presets are stored in local memory using Source keys 1 thru 4 or Destination keys 1 thru 4 as the memory preset location. - Configure desired matrices. - Press MEMORY button. - Press 1 thru 4 on either Source or Destination row. - Press ENTER to ready memory location. - Or press MEMORY again to cancel operation. Operation completes. Note: Operation will abort if no keys are dressed within 5 seconds.
BACK PANEL BACK PANEL 1. DC POWER INLET: The Switcher is fitted with a DC power plug-park input connector. Please ensure that the plug-park used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 2A Max. Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power input -12VDC, 2A 2.
REMOTE CONTROL Before making any connections to the SB-5544LCM. Observe the following: Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). Ensure that the power switch is OFF. Ensure that all system grounds (earth) are connected to a common point. Avoid powering equipment within a system from multiple power sources that may be separated by large distances. Connect all audio video sources and destination equipment. Power up all source and destination audio-visual sources.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : POWER ON : 20DF A15E POWER OFF : 20DF A25D ALL : 20DF B04F OFF : 20DF B14E CUSTOM CODE : 20DF LOCK : 20DF B54A RECALL : 20DF B24D ENTER : 20DF B34C MEMORY : 20DF B44B PRESS TV DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 20DF 01EF DESTINATION #2 : 20DF 02DF DESTINATION #3 : 20DF 03CF DESTINATION #4 : 20DF 04BF SOURCE #1 : 20DF 01FE SOURCE #2 : 20DF 02FD SOURCE #3 : 20DF 03FC SOURCE #4 : 20DF 04FB Fo
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
RS-232 SERIAL INTERFACE RS-232 Pin RS-232 Definition 1 ------ Not used 2 TX Transmitter 3 RX Receiver 4 ------ Not used 5 GND Ground 6 ------ Not used 7 ------ Not used 8 ------ Not used 9 ------ Not used RS-232 PROTOCOL COMMANDS ( RS-232 Control driver V2.0.1 ) The ShinybowUSA switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system.
TYPICAL APPLICATION 4X A/V (COMPOSITE VIDEO) SOURCES TO 4X A/V OUTPUT MATRIX SWITCHER SB-5544LCM INSTALLING CONTROL PORTS: 1. IR REMOTE - IR Remote Controller 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.