M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5548BNC 8x8 AUDIO-VIDEO MATRIX SWITCHER 8x8 AUDIO-VIDEO MATRIX SWITCHER Composite Video-Stereo Audio Matrix Switcher Series Thank you for purchasing the SB-5548BNC 8x8 Composite Video-Audio Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 FEATURES & SPECIFICATIONS .....................................2 FRONT PANEL .................................................................3 BACK PANEL ....................................................................6 REMOTE CONTROL .......................................................7 REMOTE PROTOCOL COMMANDS ................................8 RS-232 SERIAL INTERFACE .......
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • • • • • Supports (8)x inputs to (8)x outputs A/V (Composite Video & Stereo Audio) Matrix Switcher Input/Output signals via Composite Video (BNC) & Stereo Audio(AR/AL) Higher Video Bandwidth 450MB each path signals. Supported selection buttons direct channel on front panel Video support Composite Video switch the NTSC or PAL TV system, via BNC connectors.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) audio on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show ”0” indicating all destinations have no audio selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 9. FUNCTION KEY - OFF Disables (mute) audio to selected channels.
FRONT PANEL FRONT PANEL 13. FUNCTION KEY - VOL / BAL ( Volume / Balance ) VOLUME: To affect the volume on any Output, - Press VOL / BAL button once. - Select 1 thru 8 on the Destination row, for the Output you wish to change. - Press Volume + or – (Source #1 or #2 ) button to adjust the audio volume level. - Press ENTER to store the new setting. Repeatedly depressing the Source 1 button will decrease the volume setting. Repeatedly depressing the Source 2 button will increase the volume setting.
BACK PANEL BACK PANEL 1. DC POWER INLET: The Switcher is fitted with a DC power plug-park input connector. Please ensure that the plug-park used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 3A Max. Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power input -12VDC, 3A 2. IR EXTENDER CONTROL: Support one of IR Extender (IR input) Extend distance maximum 300 Meters.
REMOTE CONTROL Before making any connections to the SB-5548BNC. Observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : CUSTOM CODE : 2CD3 POWER ON 2CD3 A15E BALANCE + 2CD3 EE11 POWER OFF 2CD3 A25D BALANCE - 2CD3 ED12 ALL 2CD3 B04F LOCK 2CD3 B54A OFF 2CD3 B14E RECALL 2CD3 B24D VOLUME + 2CD3 C33C ENTER 2CD3 B34C VOLUME - 2CD3 C43B MEMORY 2CD3 B44B PRESS TV DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 2CD3 10EF SOURCE #1 : 2CD3 01FE DESTINATION #2 : 2CD3 20DF SOURCE #2 : 2CD3
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V1.0 & V1.5 For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
TYPICAL APPLICATION 8X A/V (COMPOSITE VIDEO) SOURCES TO 8X A/V OUTPUT MATRIX SWITCHER SB-5548BNC INSTALLING CONTROL PORTS: 1. IR REMOTE - IR Remote Controller 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM EDIA AUDIO A ND V IS UA L 1399 Wildfire Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.