M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5548LCM 8x8 Composite Video Stereo/Digital Audio Matrix Routing Switcher 8x8 Composite Video Stereo/Digital Audio Matrix Routing Switcher Composite Video Stereo/Digital Audio Matrix Routing Switcher Series Thank you for purchasing the SB-5548LCM Composite Video Stereo/Digital Audio Matrix Routing Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 FEATURES & SPECIFICATIONS .....................................2 FRONT PANEL .................................................................3 BACK PANEL ....................................................................6 REMOTE CONTROL .......................................................7 REMOTE PROTOCOL COMMANDS ................................8 RS-232 SERIAL INTERFACE .......
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • Supports 8x inputs to 8x outputs A/V (Composite Video-Audio) Matrix Switcher Input/Output signals via Composite Video & Stereo Audio(AR/AL) Higher Video Bandwidth 450MB each path signals.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show ”0” indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected and assign that source to all destinations. - Press ENTER The pre-set source selection will be assigned all destinations. 9.
FRONT PANEL FRONT PANEL 12. FUNCTION KEY - MEMORY The system will show store presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Configure desired matrices . - Press MEMORY button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER to ready memory location. - Or press MEMORY again to cancel operation. Operation completes. Note: Operation will abort if no keys are dressed within 5 seconds.
BACK PANEL BACK PANEL 1. DC POWER INLET: The switcher is fitted with a DC power plug input connector. Please ensure that the plug used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 1A-2A Max. Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power input -12VDC, 1A-2A 2. IR EXTENDER CONTROL: Support one of IR Extender (IR input) Extend distance maximum 300 Meters or 1000 feet.
REMOTE CONTROL Before making any connections to the SB-5548LCM. Observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : POWER ON : 2CD3 A15E POWER OFF : 2CD3 A25D ALL : 2CD3 B04F OFF : 2CD3 B14E CUSTOM CODE : 2CD3 LOCK : 2CD3 B54A RECALL : 2CD3 B24D ENTER : 2CD3 B34C MEMORY : 2CD3 B44B PRESS TV DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 2CD3 01FE DESTINATION #2 : 2CD3 02FD DESTINATION #3 : 2CD3 03FC DESTINATION #4 : 2CD3 04FB DESTINATION #5 : 2CD3 05FA DESTINATION #6 : 2CD3 06F9 DESTINATION #7 : 2CD3 07F8 DESTINATION
RS-232 SERIAL INTERFACE RS-232 Pin RS-232 Definition 1 ------ Not used 2 TX Transmitter 3 RX Receiver 4 ------ Not used 5 GND Ground 6 ------ Not used 7 ------ Not used 8 ------ Not used 9 ------ Not used RS-232 PROTOCOL COMMANDS ( RS-232 Control driver V2.0.1 ) The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
TYPICAL APPLICATION 8X A/V (COMPOSITE VIDEO) SOURCES TO 8X A/V OUTPUT MATRIX SWITCHER SB-5548LCM INSTALLING CONTROL PORTS: 1. IR REMOTE - IR Remote Controller 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM EDIA AUDIO A ND V IS UA L 1399 Wildfire Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.