M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5654K 1x4 DISTRIBUTION AMPLIFIER 1x4 HDMI 4K2K Distribution Amplifier with Scaler HDMI-4K2K Distribution Amplifier series Thank you for purchasing the SB-5654K HDMI Distribution Amplifier with Scaler. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 1x4 HDMI 4K2K Distribution Amplifier.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: FEATURES ...................................................................... 2 SPECIFICATIONS ............................................................ 3 FRONT PANEL ....
FEATURES FEATURES • (1)x HDMI 4K2K Standard input distribution To four (4)x HDMI 4K2K Distribution Amplifier. • HDMI digital Video w/embedded HDCP, DVI format and CEC/HDCP 2.0 compliant. • Build in three (3) worldwide Embedded EDID modes control HDMI full 4K2K (24/25/30Hz) resolutions. • Link speeds of up to 6.75 Gbps (link clock rate of 340MbHz), Support HDMI 1.4a, 3D formats. • Wide range of HD DVI resolutions from PC XGA to WUXGA 1920x1200 and HDTV/DTV.
SPECIFICATIONS SPECIFICATIONS • Type of HDMI DA: 1x input To 4x Outputs HDMI Distribution Amplifier with Scaler • Inputs: 1x HDMI (HDMI or DVI digital source) • Outputs: 4x HDMI (To Destination) • Audio Outputs: Multi-channel Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTS-ES 6CH, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH) • HDMI Support: HDMI 4K2K, 1080P-@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats • HDCP / CEC Support: HDCP 2.
FRONT PANEL FRONT PANEL 1. EDID Mode 1 : 1080p-2ch Digital Video 1080p (1920x1080)@60Hz, Digital Audio Multi-Channel Audio 2CH 2. EDID Mode 2 : 1080p-BitStream Digital Video 1080p (1920x1080)@60Hz Digital Audio Multi-Channel Audio :Multi Audio Formats 5.1 / 7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital Plus, DTS, DTSES 6CH, DTS-HD, DTS-HD-HRA, DTS-HD Master, (PCM-2CH) 3.
REAR PANEL REAR PANEL 1. DC POWER INLET The Switcher is fitted with a DC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 12Volt DC power supply 1A Max (Center pin positive). Power Jack: DC Jack - Inner OD ᴓ 2.1mm (+ ) Outside OD ᴓ 5.5mm (GND) Power input - 12VDC, 1A 2. FIRMWARE UPDATE Firmware update port to allow for interfacing to a PC mini-USB.
EDID FUNCTION EMBEDDED EDID & SCALER MODES FOR HDMI DISTRIBUTION AMPLIFIER EDID / Scaler setup To change the EDID & Scaler modes The display will show the currently selected EDID mode Step 1. Press SELECT button The button will flash blue and the display will show the current Embedded EDID & Scaler Status. Step 2. Press the ENTER button To set EDID & Scaler mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION EDID MODE RESOLUTION & MULTI-CHANNEL AUDIO FORMATS: RESOLUTIONS MULTI-CHANNEL FORMATS: Mode # 1 1080p@60Hz (NATIVE) 1080p@50Hz 1080p@30Hz 1080p@25Hz 1080p@24Hz 1080i@60Hz 1280x720@60Hz 720p@60Hz 720i@60 480p@60 LPCM-2ch, 32kHz ~ 48kHz, 16/20/24 bits Mode # 2 1080p@60Hz (NATIVE) 1080p@50Hz 1080p@30Hz 1080p@25Hz 1080p@24Hz 1080i@60Hz 1280x720@60Hz 720p@60Hz 720i@60 480p@60 LPCM-8ch, 32kHz ~ 192kHz, 16/20/24 bits AC-3 6ch, 32kHz ~ 192kHz, 640kHz DTS 6ch, 32kHz ~ 192kHz, 1536kHz Dolby+-8ch,
TYPICAL APPLICATION INSTALLING DIAGRAM Samples connection : Using the press button to select the Embedded EDID modes or Scaler modes to control HDMI Distribution Amplifier SB-5654K via SELECT and ENTER press buttons. NOTE : 1. Update TX/RX chip Firmware via a PC USB. 2. Scaling up 4K2K@24Hz mode : Support Input 1080p@24Hz resolution only. 3. Scaling down 1080p@24Hz mode : Support Input 4K2K@24Hz resolution only. Application use 1080p or 4K2K HDTV via 1x4 Distribution Amplifier with Scaler.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM EDIA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.