M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5654 1x4 HDMI DISTRIBUTION AMPLIFIER 1x4 HDMI DISTRIBUTION AMPLIFIER HDMI DISTRIBUTION AMPLIFIER Series Thank you for purchasing the SB-5654 1x4 HDMI DISTRIBUTION AMPLIFIER. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: FEATURES & SPECIFICATIONS .................................... 2 FRONT PANEL .................................................................. 3 REAR PANEL ...................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • • • • Support 1x4 HDMI Distribution Amplifier I/O Signals : HDMI with HDCP Digital Video and Digital Audio (PCM) HDMI and HDCP compliant Support link speeds of up to 2.
FRONT PANEL FRONT PANEL 1. POWER SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power 2. INPUT SOURCES STATUS DISPLAY Input source 1 to 4 LED illuminates blue to indicate that a video source is present on that input. 3. IR SENSOR The IR sensor receives IR commands from the supplied remote controller. 4.
REAR PANEL REAR PANEL 1. DC POWER INLET The distributor is fitted with a DC power plug-park input connector. Please ensure that the plug-park used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 1A~2A Max. Power Jack: DC Jack - Inner OD ᴓ 2.1mm (+ ) Outside OD ᴓ 5.5mm (GND) Power input - 12VDC, 1A~2A 2. INPUT - 1x HDMI Connect a signal link of HDMI direct digital video/audio to this Female HDMI connector.
REMOTE CONTROL Before making any connections to the SB-5654. Observe the following: > Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%) > Connect all audio video sources and destination equipment > Ensure that the power switch is OFF > For each destination output select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote control. Or through the RS-232 serial communications port.
TYPICAL APPLICATION TYPICAL APPLICATION 1x HDMI source to 4 x HDMI displays Distribution Amplifier INSTALLING INPUT PORT SIGNAL : 1. HDMI - HDMI connector with fix screw OUTPUTS PORT SIGNALS: 1. HDMI - HDMI connector with fix screw 2. HDMI - HDMI connector with fix screw 3. HDMI - HDMI connector with fix screw 4.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.