M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5680CAK 8x8 HDMI-HDBaseT Matrix Switcher 8x8 HDMI-HDBaseT Matrix Switch with Auxiliary Audio I/O HDMI-HDBaseT-AUDIO MATRIX SWITCHER SERIES Thank you for purchasing the SB-5680CAK HDMI-HDBaseT Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 8x8 HDMIHDBaseT Matrix switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 PACKAGE CONTENTS .................................................. 2 FEATURES ....................................................................... 3 SPECIFICATIONS ............................................................ 4 FRONT PANEL ................................................................. 5 FRONT PANEL- ARC ...................................................
PACKAGE CONTENTS PACKAGE CONTENTS Check that you have the following components; • SB-5680CAK Matrix Switcher • Master wireless IR Remote Control (SW-5680) • 8 each; Individual wireless IR Control (SW-5680-IR01~IR08) • 19 inch Ear mount bracket (Part # 3U-440L) • SB-101 IR Extender distance ~984 feet (300M) Transmitter set. • SB-100 IR Extender distance ~984 feet (300M) Receiver set. • SB-101C IR Extender distance 6ft(2M) Transmitter Cable. • SB-100C IR Extender distance 6ft(2M) Receiver Cable.
FEATURES FEATURES Based on HDBaseT; bi-directional IR, RS-232, Multi format Audio, Ethernet and PoE. Full resolution HD Video, all HDBaseT signals over one CATx cable. • • • • • • • • • • • • • • • • • • • • • • • (8)x HDMI with Auxiliary Audio (Analog Audio) and (8)x HDBaseT Receiver devices matrix switched to (8)x HDMI with S/PDIF outputs and (8)x HDBaseT Transmitter with PoE output to (8)x destinations.
SPECIFICATIONS SPECIFICATIONS • • • • • • • • • • • • • • • • • • • • • • • Type of HDMI Switcher: 8x inputs To 8x Outputs HDMI & HDBaseT Matrix Switch with Audio and Extension HDMI Support: HDMI 4K2K, 1080p-@60Hz, H36-bit Deep color, 3D of HDMI V1.4 formats HDBaseT Support: Bi-directional IR, RS-232, Multi format Audio, Ethernet and PoE. over one CATx cable. HDCP / CEC Support: HDCP 2.2 Compliant, CEC Compliant Video Bandwidth: Double Data Rates: 340 MHz, Total 6.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LCM will illuminate blue to indicate the switcher is ON and receiving power. The switcher will remember the last setting during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. OUTPUT STATUS DISPLAY Each Output (destination ) Channel shows which input (source) is assigned. 3.
FRONT PANEL- ARC FRONT PANEL 9. FUNCTION KEY - ARC Audio Return Channel (ARC) is a feature that sends audio from the TV back down the HDMI (or HDBaseT) cable to its source device, in this case, the switcher, The audio additional on the “ Audio/ARC” port. Not all displays support ARC; check your Users Guide for additional information. ( Default = ARC Disabled ) To Enable the ARC option on a specific Output, perform the follow steps: - Press the ARC button.
FRONT PANEL- AUX FRONT PANEL 10. FUNCTION KEY - AUX The AUX FUNCTION feature allows you to replace the embedded HDMI audio signal with an audio signal that is connected to the switchers Audio AUX Input. Using the AUX function replaces the audio and does not mix the audio. ( Default = AUX Disabled ) To Enable the AUX option on a specific Output, perform the follow steps: - Press the AUX button. - On the SOURCE row, Press 1 thru 8 (the button will illuminate).
FRONT PANEL- HDBaseT FRONT PANEL 11. FUNCTION KEY - HDBaseT This switcher supports an Input signal originating from either the HDMI Input or HDBaseT Input ( Default = HDMI ). You assign the Input type by following these steps: For HDBaseT Input: - Press the HDBaseT BUTTON. - On the SOURCE row, press 1 thru 8 (the button will illuminate). - Press ENTER the new configuration will be stored. The front panel LCD display will show a “ C “ under the source port. - Or press HDBaseT again to cancel operation.
FRONT PANEL- EDID FRONT PANEL 12. FUNCTION KEY - EDID (1) Used to display change current EDID mode. - Press EDID to select new EDID mode or select - Press SOURCE row #1 or #2 Select EDID modes. - Press ENTER to ready memory location. - Or press EDID again to cancel operation. Operation completes. Note : Operation will abort if no keys are pressed within 5 seconds.
FRONT PANEL - ALL - OFF - LOCK - ENTER FRONT PANEL 13. FUNCTION KEY - ALL Disables (mute) video on all destinations OR assign the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show ”0” to indicate none of the destinations are assigned a video source. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected. - Press ENTER The pre-set source selection will be assigned all destinations. 14.
FRONT PANEL - RECALL - MEMORY FRONT PANEL 17. FUNCTION KEY - RECALL The system will show previously stored presets, up to a total of 16. Presets are stored in local memory using Source keys 1 thru 8 or Destination keys 1 thru 8 as the memory preset location. - Press RECALL button. - Press 1 thru 8 on either Source or Destination row. - Press ENTER The pre-set configuration will execute. Operation completes. Note: Operation will abort if no keys are pressed within 5 seconds.
BACK PANEL - SWITCH CONTROLS BACK PANEL 1. DC POWER INLET: The Switcher is fitted with a AC power plug input connector. Ensure that the used is of an approved type and is of sufficient current carrying connector capacity with the correct voltage and connector polarity. 100~240Volt AC, 50/60Hz power supply. Power Socket : Connector Type : IEC 60320 C13 2. IR EXTENDER CONTROL: Support one of IR Extender. Extend distance maximum 300 Meters / ~984 feet.
BACK PANEL - HDMI INPUT / OUTPUT BACK PANEL 5. INPUTS- 1,2,3,4,5,6,7, & 8 HDMI: Connect a HDMI signal source link of HDMI source direct HDMI digital video/audio to this Female HDMI connector. This HDMI port support HDMI and DVI digital video sources. If you remove the HDMI screw post, use the provides IOS screw to keep the internal HDMI jack secure. Removing the HDMI Screws without installing the ISO screws will void your warranty. HDMI Connector: HDMI Type A SMD 19pin Female socket connector.
BACK PANEL - HDBaseT CONTROLS BACK PANEL 8. HDBaseT LAN CONNECTION: All Tx LAN : Provides Ethernet (LAN) connection from the switcher to All HDBaseT Transmitter (ie. SB-6320T). ALL HDBaseT Tx LAN Port Connector: HDBaseT Phone-Jack 8P8C, RJ-45 Female socket. LAN Controls: Note: from switcher to HDBaseT Transmitter. All Rx LAN : Provides Ethernet (LAN) connection from the switcher to All HDBaseT Receiver (ie. SB-6320R). ALL HDBaseT Rx LAN Port Connector: HDBaseT Phone-Jack 8P8C, RJ-45 Female socket.
BACK PANEL - HDBaseT I/O BACK PANEL 15. INPUT - 1,2,3,4,5,6,7 & 8 HDBaseT (Receiver): To Receive (8) HDMI and control signals via Switcher (8)x HDBaseT Receivers to link of Switcher HDBaseT Transmitter. Switcher used (8)x HDBaseT Receiver Input #1 ~ Input #8 with RJ-45 via CATx (6/6a/7) category extend cable. Controls signals RS-232, ethernet, IR input & output between Transmitter and Switcher. HDBaseT Receiver Connector: 8x RJ-45 Jack 8P8C Female socket.
HDBaseT I/O TRANSMISSION HDBASET I/O TRANSMISSION RS-232 Cable Pins Out: PC 232 PINS DB-9P, MALE plug HDBaseT Transmitter SB-6320T: RS-232 PINS OUT DB-9P, FEMALE socket HDBaseT Receiver SB-6320R: RS-232 PINS OUT DB-9P , FEMALE socket 16
REMOTE CONTROL Before making any connections to the switcher, observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : POWER ON : 41BE A15E POWER OFF : 41BE A25D ARC : 41BE B847 AUX : 41BE 9966 HDBaseT : 41BE 9A65 ALL : 41BE B04F OFF : 41BE B14E CUSTOM CODE : 41BE LOCK : EDID : RECALL : ENTER : MEMORY : 41BE 41BE 41BE 41BE 41BE B54A B748 B24D B34C B44B PRESS DESTINATION - # then PRESS SOURCE - # DESTINATION #1 : 41BE DESTINATION #2 : 41BE DESTINATION #3 : 41BE DESTINATION #4 : 41BE DESTINATION #5 : 41BE DESTINATION #6 : 41BE
REMOTE CONTROL ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES IR CUSTOM AND DATA CODES (NEC Standard) PRESS Number To Select SOURCE CUSTOM CODE : 41BE IR-01 DATA CODE: SOURCE #1 : 41BE SOURCE #2 : 41BE SOURCE #3 : 41BE SOURCE #4 : 41BE SOURCE #5 : 41BE SOURCE #6 : 41BE SOURCE #7 : 41BE SOURCE #8 : 41BE 11EE 12ED 13EC 14EB 15EA 16E9 17E8 18E7 IR-03 DATA CODE: SOURCE #1 : 41BE SOURCE #2 : 41BE SOURCE #3 : 41BE SOURCE #4 : 41BE SOURCE #5 : 41BE SOURCE #6 : 41BE SOURCE #7 : 41BE SOURCE #8 : 41BE 31C
REMOTE CONTROL ROOM REMOTE CONTROL #1 ~ #8 CUSTOM CODE AND DATA CODES IR CUSTOM AND DATA CODES (NEC Standard) PRESS Number To Select SOURCE CUSTOM CODE : 41BE IR-05 DATA CODE: SOURCE #1 : 41BE SOURCE #2 : 41BE SOURCE #3 : 41BE SOURCE #4 : 41BE SOURCE #5 : 41BE SOURCE #6 : 41BE SOURCE #7 : 41BE SOURCE #8 : 41BE 51AE 52AD 53AC 54AB 55AA 56A9 57A8 58A7 IR-07 DATA CODE: SOURCE #1 : 41BE SOURCE #2 : 41BE SOURCE #3 : 41BE SOURCE #4 : 41BE SOURCE #5 : 41BE SOURCE #6 : 41BE SOURCE #7 : 41BE SOURCE #8 : 41BE 718
EDID FUNCTION EDID FUNCTION FOR HDMI MATRIX SWITCHER EDID Setup To Change the EDID Setup Step 1. Press the EDID button The display will show the currently selected EDID mode Step 2. Press SOURCE #1 or #2 button row The button will flash blue and the display will show the current Embedded EDID Status. Step 3. Press the ENTER button To set EDID mode. The switcher will return to operation mode. Operation will abort if no keys are pressed within 5 seconds.
EDID FUNCTION Mode 5 . H36-3D-M (1080p-36 bits) Audio Support : MAT(MLP) 7.1CH, PCM 2CH, One Bit Audio 2CH, AC-3 5.1CH, DTS 5.1CH, PCM 7.1CH, Dolby Digital + 7.1CH, DTS-HD 7.1CH Mode 6 . 4K2K (24/30Hz) HDMI Support : 4K2K-3D, PCM 2CH (3860x2160-24/30Hz) Audio Support: PCM 2CH Mode 7 . 1920x1200-60Hz (DVI-D) DVI Support : DVI-D 1920 x 1200 60Hz Mode 8 . AUTO All Outputs will be set to the highest common resolution of all connected display devices.
EDID FUNCTION Learning EDID Single to Single Example : Learn Destination #8 EDID To Source #5. Step 1. Press EDID button The button will flash blue and the display will show the current Embedded EDID Status. Step 2. Press the Destination #8 button row Copy the Destination #8 Display EDID. Step 3. Press the Source #5 button row Learning the Destination #8 EDID to Source # 5. Step 4. Press ENTER button To confirm entries.
TYPICAL APPLICATION INSTALLING DIAGRAM Samples connection : 1. Using IR External, RS-232 or Ethernet command to control Switcher SB-5680CAK via PC or SB-100 IR receiver transmit the SB5680CAK’s IR signal. 2. Audio output link ARC from TV return channel, HDMI audio source or mixing Auxiliary audio. NOTE: 1. Switcher IR External port : Use SB-100 IR signal Receiver. 2. Control HDMI TV ARC: Use SB-5680CAK ARC function. 3. Control Switch via a PC RS-232. 4. Control Switch via a PC Ethernet.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using SB-5680CAK HDBaseT Transmitter & Receiver with HDBaseT Transmitters (SB-6320T) and HDBaseT Receiver (SB-6320R) to control a projector via RS-232 or IR signals. NOTE: 1. IR Control Projector Over HDBaseT Extender: SB-5680CAK HDBaseT Transmitter & Receiver SB-6320T/SB-6320R HDBaseT Transmitter & Receiver 2. Projector RS-232 Control by a PC via HDBaseT Extender. 3. Projector IR control via HDBaseT Extender IR in/out. 4.
TYPICAL APPLICATION INSTALLING DIAGRAM Table list is all RS-232 or IR signals control define via HDBaseT Transmitter & Receiver and SB-5680CAK Switcher.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using SB-5680CAK with HDBaseT Receiver (SB-6320R) via and IR Transmitters (SB-101) and IR Receiver (SB-100) to control a projector. NOTE: 1. Using IR control Projector Over HDBaseT Extender: HDBaseT Transmitter : SB-5680CAK HDBaseT Tx HDBaseT Receiver : SB-6320R HDBaseT Rx 2. IR Extender Transmitter (SB-101): Use SB-101 IR Transmitter : to Extend IR signal to control Projector. 3.
TYPICAL APPLICATION INSTALLING DIAGRAM Sample connection using SB-5680CAK with IR Transmitters (SB-101) via SB-6320R to control a IR signal from Satellite Receiver. NOTE: 1. IR Control Satellite Receiver Over HDBaseT Extender via CATx (6/6a/7) cable: HDBaseT Transmitter : SB-5680CAK HDBaseT Receiver : SB-6320R 2. IR Extender Transmitter (SB-101): Use SB-101 IR Transmitter to Extend IR signal to Satellite Receiver player. * HDBaseT Extender use category CATx (6/6a/7) cable.
HDBaseT APPLICATION APPLICATION HDBaseT Matrix Switcher using HDBaseT Transmitters & Receiver (Sold separately). HDBaseT Transmitter with Audio: SB-6320T Distance: Max. 100M INPUTS: 1. 1x HDMI source 2. 1x DVI Audio 3. 1x IR External in OUTPUTS: 1. 1x HDBaseT out Controls: 1x RS-232, 1x IR in, 1x IR out, 2x LAN (Ethernet) 1. Status via LED Show out : POWER, LINK & HDMI 2. 2x Ethernet path to HDBaseT Receiver 3. IR signal to HDBaseT Receiver 4. IR signal to HDBaseT Receiver 5.
HDBaseT APPLICATION APPLICATION Optional 19 inch Rack Mount Bracket for SB-6320T and/or SB-6320R: Complete 19 inch 4U rack mount of SB-6069 Install Application : SB-6320T/R SB-6069 (optional) SB-6320T/R 19 INCH 4U-10P RACK MOUNT 1. Model No. : #4U-10p-M130MM SB-6320T/R 4U Ear mount pairs Parts No.: MEER6069ER13000 2. Model No. : #4U-10p-M130MM-COV SB-6320T/R 4U Ear mount pairs Parts No.: MEER6069ER11000 SB-6320T/R : Wall mount accessories 3. Model No.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
ETHERNET SERIAL INTERFACE ETHERNET SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION COMPATIBLE V2.0 For a complete list of commands, please reference external document extended Ethernet Protocol Instruction Manual.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM. VERSION -2.0 COMPATIBLE For a complete list of commands, please reference external document extended RS-232 Protocol Instruction Manual. RS-232 SERIAL INTERFACE Pin RS-232 Definition 1 -------- Not used 2 TX Transmitter 3 RX Receiver 4 -------- Not used 5 GND Ground 6 -------- Not used 7 -------- Not used 8 -------- Not used 9 -------- Not used RS-232 PROTOCOL COMMANDS (RS-232 Control driver V2.0.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.