M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-8188CT 8x8 VGA-AUDIO CAT5 MATRIX SWITCHER 8x8 VGA-AUDIO CAT5 MATRIX SWITCHER 8x8 VGA-AUDIO Over CAT5 Matrix Switcher Series Thank you for purchasing the SB-8188CT VGA(RGBHV) Over CAT5/6 Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use this switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ..............................................................1 FEATURES & SPECIFICATIONS .....................................2 FRONT PANEL .................................................................3 BACK PANEL ....................................................................4 REMOTE CONTROL .......................................................5 REMOTE PROTOCOL COMMANDS ................................6 RS-232 SERIAL INTERFACE .......
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • • Supports 8x inputs VGA+Audio to 8x CAT5 outputs Matrix Switcher Input signals support via VGA (RGBHV), Stereo Audio(AR/AL) Output Signals support via CAT5-CAT6 category cable to VGA Monitor displays Higher Video Bandwidth 325MB each path R,G,B signals.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. OUTPUT SOURCES STATUS LED DISPLAY Output channel 1 to 8 show from LED display illuminates red to indicate that a video source is present on that input. 3.
BACK PANEL BACK PANEL 1. DC POWER INLET: The switcher is fitted with a DC power plug input connector. Please ensure that the plug used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 3A Max. Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power input -12VDC, 3A Switcher power supply use universal part number TA 007 2.
REMOTE CONTROL Before making any connections to the SB-8188CT. Observe the following: • Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). • Ensure that the power switch is OFF. • Ensure that all system grounds (earth) are connected to a common point. • Avoid powering equipment within a system from multiple power sources that may be separated by large distances. • Connect all audio video sources and destination equipment.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC STANDARD) HOW TO SETUP IR CODES : POWER ON : 00FF 04FB POWER OFF : 00FF 05FA Monitor IN / VGA Sources OUT INPUT#1 / OUTPUT#1 : 01FE 31CE INPUT#1 / OUTPUT#2 : 01FE 32CD INPUT#1 / OUTPUT#3 : 01FE 33CC INPUT#1 / OUTPUT#4 : 01FE 34CB INPUT#1 / OUTPUT#5 : 01FE 35CA INPUT#1 / OUTPUT#6 : 01FE 36C9 INPUT#1 / OUTPUT#7 : 01FE 37C8 INPUT#1 / OUTPUT#8 : 01FE 38C7 INPUT#2 / OUTPUT#1 : 02FD 31CE INPUT#2 / OUTPUT#2 : 02FD 32CD INPUT#2 / OUTPUT#3 : 02FD 33CC I
RS-232 SERIAL INTERFACE RS-232 RS-232 SERIAL CONNECT The ShinybowUSA switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system. Pin RS-232 1 ------ Not used The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
TYPICAL APPLICATION 8X VGA( RGBHV) SOURCES TO 8X CAT5 VGA -AUDIO OUT PUT MATRIX SWITCHER SB-8188CT INSTALLING CONTROL PORTS: 1. IR REMOTE - IR Remote Controller 2. RS-232 Interface - RS-232 interface system INPUTS 1 ~ 8 PORT VGA SOURCE SIGNALS: VIDEO - VGA (RGBHV), connector with HD-15p (D-Sub) AUDIO - Stereo Audio (AR/AL), Connector via OD3.
IR EXTENDER IR RECEIVER: 1. SB-100 IR 300M Receiver Device Cable (3C) IR Receiver (SB-100) R oHS /95/E C IR E XT. in RS - 232 IR EXT . INP UT DC 12V 4 3 UT 4 -2 3 -4 UT IR 2 R IX IN P I MAT SW 1 HDM 1 S WIT UT 2 IN P 1 SB-100 C HE -3 R 3 UT ER 2 IN P P OW 2 ON 1 IN P IR Rx OFF -1 3 4 4 R S -232 SB-100 IR Receiver Set 2.
IR EXTENDER IR EMITTER: 1. SB-101 IR 300M Transmitter DC 12V Device Cable (3C) IR out IR in CAT6/6a/7 From Receiver To Receiver OUTPUT IR Transmitter (SB-101) R oHS /95/E C IR Tx SB-101 SB-101 IR Transmitter Set 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.
