M U LT IM EDIA AUDIO A ND V IS UA L 8x8 Composite Video Stereo/Digital Audio Matrix Routing Switcher INSTRUCTION MANUAL MODEL : SB-5548 8x8 Composite Video Stereo/Digital Audio Matrix Routing Switcher Composite Video Stereo/Digital Audio Matrix Routing Switcher Series Thank you for purchasing the SB-5548 Composite Video Stereo/Digital Audio Matrix Routing Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
INTRODUCTION INTRODUCTION ..................................................3 FEATURES & SPECIFICATIONS ...........................4 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, FRONT PANEL .....................................................5 REAR PANEL ........................................................6 REMOTE CONTROL ............................................7 IR EXTENDER ......................................................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • Supports 8x inputs to 8x outputs A/V (Composite Video-Audio) Matrix Switcher Input/Output signals via Composite Video & Stereo Audio (AR/AL) Higher Video Bandwidth 450MB each path signals.
FRONT PANEL FRONT PANEL 1. POWER ON SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power. The Switcher will remember that last state during a power cycle. When power is removed and resorted, the last configuration will be evoked. 2. INPUT STATUS DISPLAY Input sources 1 to 8 LED illuminates blue to indicate that a video source is present on that input. 3.
FRONT PANEL cont’d FRONT PANEL 8. FUNCTION KEY - ALL Disables (mute) video on all destinations OR Selects the same source to all destinations. Option 1 - Press ALL followed by OFF button. The display will show” a • indicating all destinations have no video selected. Option 2 - Press ALL followed by Source 1 thru 8. The display will show the Source selected and assign that source to all destinations. 9. FUNCTION KEY - OFF Disables (mute) video to selected channels. Either Sources or destinations.
BACK PANEL BACK PANEL Power Jack: DC Jack - Inner OD Ø 2.1 mm (+) Outside OD Ø 5.5mm (GND) Power input -12VDC, 1A-2A 1. DC POWER INLET: The switcher is fitted with a DC power plug input connector. Please ensure that the plug used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 1A-2A Max. 2. IR EXTENDER CONTROL: Support one of IR Extender (IR input) Extend distance maximum 300 Meters or 1000 feet.
REMOTE CONTROL Before making any connections to the SB-5548. Observe the following: Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%). Ensure that the power switch is OFF. Ensure that all system grounds (earth) are connected to a common point. Avoid powering equipment within a system from multiple power sources that may be separated by large distances. Connect all audio video sources and destination equipment. Power up all source and destination audio-visual sources.
REMOTE PROTOCOL COMMANDS IR REMOTE CUSTOM AND DATA CODES (NEC Standard) HOW TO SETUP IR CODES : CUSTOM CODE : 00 FF POWER ON : 00FF 00FF POWER OFF : 00FF 01FE ALL : 00FF B04F OFF : 00FF B14E PRESS TV DESTINATION - # then PRESS AV SOURCE - # DESTINATION #1 : IR auto suggestion DESTINATION #5 : IR auto suggestion SOURCE #1 : 10EF 01FE SOURCE #2 : 10EF 02FD SOURCE #3 : 10EF 03FC SOURCE #4 : 10EF 04FB SOURCE #5 : 10EF 05FA SOURCE #6 : 10EF 06F9 SOURCE #7 : 10EF 07F8 SOURCE #8 : 10EF 08F7 SOURCE #1 : 50AF
RS-232 SERIAL INTERFACE RS-232 RS-232 SERIAL CONNECT The Shinybow switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC, or similar third party control system. Pin RS-232 1 ------ Not used The serial communication parameters are 9600 baud, 8 bit, No Parity and 1 stop bit - this is often referred to as 9600 8N1. When the unit recognizes a complete command it will perform the requested action - there is no delimiter character required.
IR EXTENDER REAR PANEL IR EXTENDER PORT *** When you plug the External IR extender into the switcher, the front panel IR receiver remains active.
TYPICAL APPLICATION 8x A/V (Composite Video) sources to 8x A/V Output Matrix Switcher SB-5548 INSTALLING CONTROL PORTS: 1. IR REMOTE - IR Remote Controller 2.
LIMITED WARRANTY SHINYBOW WARRANTY SHINYBOW Technology warrants this product against defects in materials and workman ship for a period of 3 years from the date of purchase. Please be sure to send in your warranty registration card promptly, as the warranty will not be active without registration.
M U LT IM EDIA AUDIO A ND V IS UA L 1399 Wildfire Lane | Frisco, TX 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.