M U LT IM EDIA AUDIO A ND V IS UA L INSTRUCTION MANUAL MODEL : SB-5644 4x4 COMPONENT- AUDIO MATRIX SWITCHER 4x4 COMPONENT- AUDIO MATRIX SWITCHER Component Matrix Switcher Series Thank you for purchasing the SB-5644 Component-Audio Matrix Switcher. You will find this unit easy to install and highly reliable but it is essential that you read this manual thoroughly before attempting to use 4x4 ComponentAudio Matrix Switcher.
SAFETY INFORMATION 1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. 2. Follow all instructions printed on unit chassis for proper operation. 3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. 4. Make sure power outlets conform to the power requirements listed on the back of the unit.
TABLE OF CONTENTS CONTENTS SAFETY PRECAUTIONS INTRODUCTION ...............................................................1 Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: FEATURES & SPECIFICATIONS ....................................2 FRONT PANEL .................................................................3 REAR PANEL ......................
FEATURES & SPECIFICATIONS FEATURES • • • • • • • • • Supports 4x inputs to 4x outputs Component Video (YPBPR) Matrix Switcher Input/Output signals via Component Video(YPBPR), Digital (PCM), Stereo Audio (AR/AL) Higher Video Bandwidth 325MB each path signals.
FRONT PANEL FRONT PANEL 1. POWER SWITCH The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and is receiving power 2. OUTPUT SOURCES STATUS LED DISPLAY Output channel 1 to 4 show from LED display illuminates red to indicate that a video source is present on that input. 3. UP SELECT INPUT SOURCE BUTTONS Setup the input sources 1 ~ 4 channels 4. DOWN SELECT INPUT SOURCES Setup the input sources 1 ~ 4 channels 5.
REAR PANEL REAR PANEL 1. DC POWER INLET The SB-5644 is fitted with a DC power plug-park input connector. Please ensure that the plug-park used is of an approved type and is of sufficient current carrying capacity with the correct voltage and connector polarity. 12Volt DC power supply 1.25A Max. Power Jack: DC Jack - Inner OD ᴓ 2.1mm (+ ) Outside OD ᴓ 5.5mm (GND) Power input - 12VDC, 1.25A 2.
REMOTE CONTROL Before making any connections to the SB-5644. Observe the following: > Ensure the mains voltage supply matches the label on the supplied plug- Pack (+/- 10%) > Connect all audio video sources and destination equipment > Ensure that the power switch is OFF > For each destination output select the appropriate input source by using the front panel input 1~8 select buttons. The supplied IR remote control. Or through the RS-232 serial communications port.
RS-232 SERIAL INTERFACE RS-232 SERIAL INTERFACE CONNECT A PC OR CONTROL SYSTEM RS-232 SERIAL INTERFACE Pin RS-232 Definition 1 -------- Not used 2 TX Transmitter 3 RX Receiver 4 -------- Not used 5 GND Ground 6 -------- Not used 7 -------- Not used 8 -------- Not used 9 -------- Not used RS-232 The switcher can be controlled via the RS-232 serial control port to allow for interfacing to a PC or similar third party control system.
RS-232 SERIAL COMMANDS MORE STUFF FOR SB-5644 Note: Turning the unit System Power Off over RS-232 will distinguish the LED display leaving only the Power Switch LED on. The Video and Audio outputs will also mute. While the unit is turned off by RS-232 it will continue to accept and act upon switching commands.
TYPICAL APPLICATION SHINYBOW SB-5644 4x Component sources to 4x Component Output Matrix Switcher INSTALLING CONTROL PORTS : 1. IR REMOTE - IR Remote Controller 2.
LIMITED WARRANTY PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA, Inc.
M U LT IM ED IA AUDIO A ND V IS UA L 122 Rose Ln. Suite 303 | Frisco, Texas 75034 1-877-SHINY-USA 1-877-744-6987 1-972-377-2508 sales@shinybowusa.com www.shinybowusa.