• User Manual • SD2100 Digital Enhanced Cordless Communication
Contents What the symbols mean................................................................... 1 The Handset and Base Unit ............................................................... 2 Setting up your telephone ................................................................ 3 Installation .................................................................................. 4 Important safety information ............................................................ 4 Making and answering calls ..........
The Handset and Base Unit MENU/ Mute button PHONEBOOK/OK button Press to enter menu mode and enter submenu. With the key " to lock or unlock " the keypad. Press during a call to mute the microphone In standby mode, press to enter phonebook menu. Press to confirm selection. INT button Press to make an intercom call (if you have more than one handset) Recall button Clear / On-Off /END button You can activate Recall function if your phone is connected to a PABX, or if you use Select Services.
Setting up your telephone Connection and conditions for use You can connect your SD2100 to a direct exchange line (DEL), a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the SD2100 as an extension to a payphone. How many phones can you connect? The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.
Installation 1. Choose a suitable site for the handset unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead into the power jack the base unit and plug the telephone line cord into the telephone port. 3. Plug the mains adapter into a 230 V AC, 50 Hz mains socket, with the switch on the socket set to OFF Note: The illustration of adaptor may vary from country to country. 4. Switch on mains power at the socket 5.
the base unit from the telephone line and the mains socket when there are storms in your area. Damage caused by lightning is not covered by the Guarantee. 4. The SD2100 will produce a certain amount of heat during operation. For this reason it is recommended that this equipment is NOT placed in direct contact with antique, veneered or delicate furniture surfaces. 5. DO NOT dispose batteries with normal household waste. 6.
• While the mouthpiece is muted, you cannot press any number key to send digits down the line; Press Mute key again to get back to the call. Conference Calling You need to register with your fixed line network operator for conference calling service. It is dependant on service availability and subscription. To Make Conference Call: 1. Connect the first party; 2. Press INT button, and the first party is put on hold; 3. Dial second party’s phone number; 4.
Call Logs You must subscribe to Caller ID service from your service provider to use this feature. Call Logs store information related to received calls, missed calls and dialed calls. The SD2100 can store up to a maximum of 30 calls, consisting of 10 received, missed and dialed calls respectively. To check call records 1. Press the MENU button The display shows CALL LOGS 2. Press the OK button, then press UP/DOWN button to the locations MISSED, RECEIVED, or DIALED calls. 3.
3. Press the OK button The display shows the current volume level 4. Press UP/DOWN button to change the volume 5. Press the OK button to confirm the volume level you want Ringer Melody (EXT / INT) You can choose the ringer Melody following the below instruction. 1. Press the MENU button, then press UP/DOWN button to the location HANDSET 2. Press the OK button, then press UP/DOWN button to the location EXT RING / INT RING 3. Press the OK button The display shows the current melody 4.
6. Press OK button to confirm To delete call barring number 1. Press MENU button then UP/DOWN button until the display shows BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number 4. Press the OK button, then UP/DOWN button to the location BARRING 5. Press the OK button, the display shows the call barring number you set. 6. Press the CLEAR button to delete the number 7. Press OK button to confirm Base Melody You can adjust the Base Melody following the below instruction. 1.
4. Press the OK button and press UP/DOWN button to change Dial mode as TONE or PULSE dialing To reset base 1. Press MENU button, then UP/DOWN button to the location BASE SET 2. Press the OK button, the display shows PIN? 3. Key in your PIN number and press the OK button, then UP/DOWN button to the location B RESET 4. Press OK button, then the display shows RESET? 5. Press OK button to confirm, or Press CLEAR button, and go back to B RESET To change base PIN 1.
1. Disconnect the power lead from the back of the base unit 2. Press and hold the HANDSET LOCATOR button in the base unit, at the same time connect the power lead into the back of base unit. Release the LOCATOR button after you hear “beep” sound for five times. The IN USE light on base unit lights during this whole process. 3. After 2~3 seconds, you can hear “beep” sound for two times again and the IN USE light goes off; 4.
Troubleshooting Always check first that: • You have followed the steps listed on pages to install and set up your SD2100. • All connects are firmly inserted in their sockets. • Mains power is switched on at the socket. • The handset’s batteries are correctly and securely installed, and are not run down. If you experience difficulties with the working of your SD2100, refer to the advice given below. I cannot make or answer calls.
The strange noise is caused by interference. Disconnect the mains power lead from the back of the base unit, and then wait for 30 seconds before reconnecting it. There is 'beep' sound while I am on a call. You may be going out of range of the base unit. Move closer, or your call may be cut off. Check the Batteries Level symbol on the display. If it is low, recharge the batteries. The Caller Display feature isn’t working. You need to subscribe to the Caller Display feature from your service provider.
