• User Manual • SK9151 Digital Enhanced Cordless Communication SKYPE™ DECT TELEPHONE
Contents Introduction ................................................................................ 1 Physical Details ............................................................................ 2 What the symbols mean ................................................................. 4 Setting up your telephone .............................................................. 4 Installation.................................................................................. 5 Important safety information.....
Minimum System Requirements Broadband Internet Service PC with the following minimum specifications: Pentium 400Mhz or above Windows® 2000® or XP® Available USB Port, USB2.0 or USB1.1 Skype® version 1.2 or higher (visit www.skype.com) 128Mb RAM, 256Mb RAM recommended 10Mb Hard Disk space CD ROM for Software Driver Package Content The contents of your product should contain the following items. For any missing items, please contact your dealer immediately. 1. 2. 3. 4. 5. 6. 7. 8. 9.
The Handset and Base Unit Left Key Press to enter menu and sub-menu mode; Press to confirm selection; With the key “*” to lock or unlock the keypad; Press during a call to mute the mouthpiece. Skype Key In idle mode, you can press UP key to access Skype Call List directly. Right Key Press to enter phonebook menu. Press during programming to go back to the previous option; Press to clear digits from the display. End /On-Off Key Call / Recall Key Press to end a telephone call.
What the symbols mean Batteries Charge Level Whenever this shows ‘nearly empty’ ( ), put the handset on the base unit to charge the batteries. While the batteries are being charged, the level shown will keep changing. Mute Your handset's microphone is muted. Signal Level Shows the signal between the handset and base unit, and disappear when you are out of range of the base unit. Speakerphone Your handset’s loudspeaker is on. Lock Your handset’s keypad is locked.
Installation 1. Choose a suitable site for the base unit Make sure it is not near to another telephone, nor to other electrical equipment. 2. Plug the mains power lead and the telephone line cord into the bottom of the base unit. 3. Plug the mains adapter into a 230 V AC, 50 Hz mains socket with the switch on the socket set to OFF. Note: The illustration of adaptor may vary from country to country. 4. Switch on mains power at the socket 5.
9. Mount the CD-ROM and install the program with CD installation provided. The installation should run automatically. If it doesn’t, begin the installation by opening the CD file namely Setup or Skype Dect. Follow the on-screen instructions to complete the installation. After a successful installation, you will find an icon namely Skype Dect on the desktop. Note: The Skype software must be activated on your PC before you place SkypeOut and Skype™ calls every time.
Making and Answering Calls Note: In standby mode, press any button on keypad except “Talk” button to make the backlight come on before enabling any function. (It means 1st press to turn on the backlight, 2nd press to activate the function button. This is correct for all buttons except for “Talk” button.) To Make an Ordinary Call 1. Enter the telephone number and press Call key to place call; 2. If you make a mistake, press Right key to delete incorrect digits, before you press Call key.
1. When you already engaged on an ongoing call, if another Skype call is received, press Right key to enter option menu; 2. Then press Scrolling button to select Hook up and press Left key; 3. Press Right key to enter option menu again; 4. Press Scrolling button to select Switch; 5. Press Left key to toggle the phone connection.
To Check Memory You can use this feature to see how many of your Phone Book’s locations have been not used. 1. In standby mode, press Right key, enter Phonebook mode, the display shows the stored numbers; 2. Press Left key and Scrolling button to the location memory; 3. Press Left key, the display shows “ n Free”. Call Lists You must subscribe to Caller ID service from your service provider to use this feature. Call Logs store information related to Received calls, Missed calls and Dialed calls.
To Set External/Internal Ringer Melody (1 - 9 melody) 1. Select < Ringer Set> under Handset Set mode; 2. Press Left key to confirm, then Scrolling button to the location ExternalRing / InternalRing; 3. Press Left key and Scrolling button to choose the ring melody you want to set; 4. Then press Left key to confirm the choice. To Set Key Tone On/Off Each time you press a key on your handset, you hear a tone. You can turn this off if needed. 1. Select < Ringer Set> under Handset Set mode; 2.
4. Press Left key to confirm. To Set Base Melody (1-9 melody) 1. 2. 3. 4. Select < Ringer Settings> under Base Settings mode; Select under Ringer Settings; Press Left key Scrolling button to set the melody you prefer; Press Left key to confirm. To Set Flash Time You can change flash time to short or long. 1. Select < Dial Settings> under Base Settings mode; 2. Select under Dial Settings; 3. Press Left key and Scrolling button to change Flash Time to Long or Short; 4.
1. Select under Base Settings mode; 2. Press Left key, and key in the PIN; 3. Press Left key, then key in the SHORT number that you want to replace the long number; 4. Press Left key to confirm, then key in the LONG number; 5. Press Left key to confirm. To Change Base PIN 1. 2. 3. 4. 5.
To register a USB dongle 1. Press and hold the Handset locator button on the base unit for a while, until you hear "beep" sound twice continuously; 2. Insert the USB dongle into your PC USB port, the LED will be blinking. 3. Use a paper clip or a pencil tip to depress and hold the reset button of dongle for 2~3 seconds, then release and you will hear a confirmation tone from Base unit. 4. Once registered successfully, the LED on the dongle will be turned on permanently. Extra Setting To Set Alarm Time 1.
1. 2. 3. 4. 5. Select Skype under menu mode; Select < Contact List > under Skype mode; Press Left key, then the display shows the Skype online user list; Press Scrolling button to select the record you wish to call; Press Call key to place a Skype call. Note: Press shortcut key Up-button in the scrollbar to enter the Skype contact list directly or use above steps. Quick Search: This function enables you to speed search the list by inputting the initial letter or number of the list you look for.
To Make a Skype Conference Call: 1. When you already engaged on an ongoing call, if another Skype call is received, press Right key to enter option menu; 2. Then press Scrolling button to select Hook up and press Left key; 3. Press Right key to enter option menu again; 4. Press Scrolling button to select Conference Call; 5. Press Left key to connect the three parties together.
2. The outside call is put on hold. When the call answers, you can speak to the user, then press the End key to hang up and transfer the call. Troubleshooting Always check first that: • You have followed the steps listed on pages to install and set up your SK9151. • All connects are firmly inserted in their sockets. • Mains power is switched on at the socket. • The handset’s batteries are correctly and securely installed, and are not run down.
Check the Batteries Level symbol on the display. If it is low, recharge the batteries. The Caller Display feature isn’t working. You need to subscribe to the Caller Display feature from your service provider. The caller may have withheld their number, or they may be calling from a network that does not transmit the Caller ID (for example, it may be an international call). The handset’s batteries are running low within an hour or two.
