• User Manual • SC3112 Caller ID Phone
SC3112 User Guide ! • Please ensure the phone is placed in a dry and ventilated place without corrosive air. • Please install 2 x AAA batteries for viewing the LCD display. If the LCD does not display clearly, please change the batteries to ensure the normal function of the unit. • Before operation, please check if you had applied for caller ID service from Telecom for caller ID display. Please remove any branch box or abuse resistant device to avoid failure in receiving incoming call number.
SC3112 User Guide TABLE OF CONTENT PRODUCT OVERVIEW ..................................................................................... 3 1. INSTALLING OR REPLACING THE BATTERY ......................................................... 4 2. SWITCH OPERATION................................................................................... 4 RINGER HI/LO Switch ................................................................................. 4 HANDSFREE Volume Slider ........................................
SC3112 User Guide PRODUCT OVERVIEW 21 20 22 1 19 2 18 17 16 3 4 5 15 6 7 8 9 10 11 12 13 14 Description: 1. LCD display 16. M1 key 2. DOWN key 17. RING LED indicator 3. MEMO key 18. CHECK key 4. DELETE key 19. PAUSE key 5. IN USE LED indicator 20. UP key 6. M3 key 21. Tel line jack 7. M2 key 22. RINGER HI/LO switch 8. 0-9/#/* key 9. HANDSFREE VOLUME slider 10. FLASH key 11. SET key 12. REDIAL key 13. HANDSFREE key 14. CALLBACK key 15.
SC3112 User Guide 1. INSTALLING OR REPLACING THE BATTERY Install 2 Alkaline AAA batteries into the battery compartment and re-fit the cover before use. IMPORTANT—before removing the battery compartment cover, ensure the base unit is disconnected from the telephone line. Connection and conditions for use You can connect your SC3112, to public networks in the United Kingdom or to an approved PBX using DTMF signaling. Each item of telephone equipment (phones, fax machines, etc.
SC3112 User Guide the LCD. Press number key to input the date. Once done, press SET key. OR Press 2 to set the time. The hour and minute will be flashing on the LCD. Press number key to input the time. Once done, press SET key. To exit press HANDSFREE key. ALARM Press SET key. Press 3 to display AL 1-2-3 on the LCD. Press 1, 2 or 3 to set the alarm. Press the UP key to select the time. Once done, press Set key. FLASH or Press SET key. Press 5 to display 1-F 2-PT on the LCD.
SC3112 User Guide 4. FUNCTION KEY OPERATION UP and DOWN key In any mode, press UP/DOWN key to check all the incoming numbers. If there is no incoming number, the unit will display END. The unit can receive up to 16-digit phone numbers. CHECK key Press CHECK key to check incoming and outgoing calls. Press UP/DOWN key to navigate forward and backward. DELETE key In any mode, when checking the incoming and outgoing call, press DEL key to delete the number you are checking. PAUSE key To insert a 3.
SC3112 User Guide FLASH key (600ms) In the on-hook mode, press this key to auto-hang up, after that you can press REDIAL key or dial out another number. REDIAL key In the on-hook mode, press this key to redial the last dialed number. CALLBACK key Press CALLBACK key and hold for 3 seconds to dial out the number displayed on the LCD panel with a “0” append in front of the number. HANDSFREE (HF) key While on-hook, press the HANDSFREE key to go into handsfree mode.
SC3112 User Guide (Q) I could not see the caller’s number on the LCD when there is incoming call. (A) Ensure that you have subscribed Caller ID service from your local telecom provider. (Q) There is no LCD Display / Backlight after I have connected the telephone line. I can call out normally. (A) Ensure that you have inserted the batteries on the battery compartment. If there is still no display, change the batteries and ensure it is not empty. If the problem persists, please check with your local dealer.