User Manual

CBR600RR 07-08 NO CUT Frame Slider

Installation Instructions

Part Numbers: 755-3319, 750-3319, 750-3310,

850-3310

MADE IN THE USA!

Carefully read instructions in their entirety before the install

Professional installation is recommended. Always use proper safety measures during the install of this

product. Do not try to install this product without proper tools, recently calibrated torque wrench,

correct torque specifications from factory service manual, safety goggles and gloves. The motorcycle

must be in a fixed secure position before the install process begins. DO NOT remove both engine studs

at the same time. Shogun is not responsible for any part of your motorcycle for any reason. Precisely

measure location of cut and if in doubt at any point please call us before the install process has begun.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)

QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-3319-L Black Left Side Puck

1 $20.00 99-FS-750-3310-L White Left Side Puck

1 $30.00 99-FS-850-3310-L Polished Billet Left Side Puck

1 $40.00 99-OF-750-3310-L Left Side Offset Black Anodized

1 $3.50 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 (Holds puck to offset)

Replacement Parts List: Right Side Components (as if you were sitting on the bike)

1 $20.00 99-FS-750-3319-R Black Right Side Puck

1 $20.00 99-FS-750-3319-R White Right Side Puck

1 $30.00 99-FS-850-3310-R Polished Billet Right Side Puck

1 $40.00 99-OF-750-3310-R Right Side Offset Black Anodized

1 $3.50 99-HB-SH10125070 Socket Cap 10 X 1.25 X 70 (Holds puck to offset)

Frame Sliders: Left side slider longer than right.

Installation Steps:

Some photos in this section are used for illustration examples only.

1. Remove lower panel to expose mounting locations.

2. Remove left engine stud. There is a spacer that is located between the frame and the engine.

Your left side offset will mount in this location.

PAGE 1
CBR600RR 07-08 NO CUT Frame Slider Installation Instructions Part Numbers: 755-3319, 750-3319, 750-3310, 850-3310 MADE IN THE USA! Carefully read instructions in their entirety before the install Professional installation is recommended. Always use proper safety measures during the install of this product. Do not try to install this product without proper tools, recently calibrated torque wrench, correct torque specifications from factory service manual, safety goggles and gloves.
PAGE 2
3. Mount the left side offset using the stock OEM 12mm Hex Flange bolt. Make sure that the wire loom is routed properly and not being pinched by the offset in anyway. Line up the edge of the offset (wile mounted) with the edge of the frame and torque down. 4. Use one drop of blue thread locker on the (99-HB-SH10125080) Socket Cap 10 X 1.25 X 80 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove right engine stud. There is a spacer that is located between the frame and the engine.
PAGE 3
6. Mount the right side offset using the stock OEM 12mm Hex Flange bolt. Make sure that the wire loom is routed properly and not being pinched by the offset in anyway. Line up the edge of the offset (wile mounted) with the edge of the frame and torque down. 7. Use one drop of blue thread locker on the (99-HB-SH10125070) Socket Cap 10 X 1.25 X 70 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Remount lower panel.