Owner manual

ManualsBrandsShogun Motorsports ManualsFor motorcyclesHonda CBR900RR (93-99) Frame Slider

Honda CBR900RR (93-99) Frame Slider

Installation Instructions

Part Numbers: 750-3409 & 750-3400

MADE IN THE USA!

Carefully read instructions in their entirety before the install

Professional installation is recommended. Always use proper safety measures during the install of this

product. Do not try to install this product without proper tools, recently calibrated torque wrench,

correct torque specifications from factory service manual, safety goggles and gloves. The motorcycle

must be in a fixed secure position before the install process begins. DO NOT remove both engine studs

at the same time. Shogun is not responsible for any part of your motorcycle for any reason. Precisely

measure location of cut and if in doubt at any point please call us before the install process has begun.

Replacement Parts List: Left Side Components (as if you were sitting on the bike)

QTY Price each Part Numbers Descriptions

1 $20.00 99-FS-750-3409-L Black Left Side Puck

1 $20.00 99-FS-750-3400-L White Left Side Puck

1 $3.50 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud

Replacement Parts List: Right Side Components (as if you were sitting on the bike)

1 $20.00 99-FS-750-3409-R Black Right Side Puck

1 $20.00 99-FS-750-3400-R White Right Side Puck

1 $3.50 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud

Frame Sliders: Left and right frame slider the same.

Installation Steps:

1. Some photos in this section are used for illustration examples only. It is up to you how you

decide to cut your motorcycles bodywork to accept the frame slider there are many different

ways customers go through this process. Shogun is not responsible for any part of your

motorcycle for any reason. Precisely measure location of cut and if in doubt at any point please

call us before the install process has begun. Professional installation is recommended. Always

use proper safety measures during the install of this product. Do not try to install this product

without proper tools, recently calibrated torque wrench, correct torque specifications from

factory service manual, safety goggles and gloves.

2. Body Prep. Use masking tape to completely mask off the area on the body where you will be

working. We usually will tape off approximately 6 to 8 inches around the though hole area and

any other edges that could get bumped or scratched while working. Tip: In some locations you

may want to double up the thickness of the masking take to give extra protection.

Summary of content (4 pages)

PAGE 1
Honda CBR900RR (93-99) Frame Slider Installation Instructions Part Numbers: 750-3409 & 750-3400 MADE IN THE USA! Carefully read instructions in their entirety before the install Professional installation is recommended. Always use proper safety measures during the install of this product. Do not try to install this product without proper tools, recently calibrated torque wrench, correct torque specifications from factory service manual, safety goggles and gloves.
PAGE 2
3. Locating and cutting the body. This is a simple illustration of how most of us install the product here. It takes a bit longer but our end results have been more consistent with a better overall fit and finish. We start with (99-SPOT-1012560) Shogun Spot tool. It’s nothing special just a 10mm socket cap bolt with a 1.25 pitch that we cut the head off of and sharpen to a point. You can purchase the tool for $12.99 or go to your local hardware store and make your own. Keep in mind Metric 10 or 12mm X 1.
PAGE 3
6. Using a small drill ¼ inch or so drill a pilot hole in the body from the inside out. Remount bodywork and double check the hole location with the spot tool still inserted (arrow in picture below is pointing to spot tool). With pilot hole cut and on center, remove body panel to prep for cutting. 7. A pencil was then used to draw our diameter of desired shaped hole. A flexible hole template can also be used for the same purpose.
PAGE 4
9. Remove left side bolt. Mount left side puck with (99-HB-SH10125080) 80 Main Engine Stud and torque down. Socket Cap 10 X 1.25 X 10. Remove right side bolt. Mount right side puck with (99-HB-SH10125080) Socket Cap 10 X 1.25 X 80 Main Engine Stud and torque down. READ CAREFULLY Shogun cannot guarantee that they will protect your motorcycle from any extent of damage. Shogun frame sliders are really meant to help possibly save the frame from damage in the event of a crash.