STRIX V3 USER GUIDE VERSION 1.7 Shoof Technologies Inc.
TABLE OF CONTENTS 1. Introduction .................................................................................................................. 3 2. Antenna connections .................................................................................................... 4 3. Power Connection......................................................................................................... 6 4. Labeling ........................................................................................
1. INTRODUCTION The Strix V3 an FCC part 15.247compliant device that enables communication to the Shoof Technologies data network. The Strix tag operates in the 902-928MHz, 2.4GHz and 433MHz ISM band. Figure 1 - Strix Tag Shoof Technologies Inc.
2. ANTENNA CONNECTIONS ONBOARD ANTENNAS Strix V3 has two onboard antennas: - Dual band Inverted F antenna – 2.4GHz and 900MHz Printed PCB antenna for 433MHz Dual band invertedF antenna Figure 2 - Top Side of Board 433MHz printed PCB antenna Figure 3 - Bottom Side of Board Shoof Technologies Inc.
OFFBOARD ANTENNA CONNECTION The Strix V3 has two optional off-board antenna connections. External antennas can be connected to Strix v3 according to the table and figure below: Port Connector Type Antenna type Maximum gain J8 - 900MHz MMCX Omni 3dBi J9 - 2.4GHz MMCX Omni 4dBi Table 1 - External Antennas 900MHz antenna port 2.4GHz antenna port Figure 4 - Offboard Antenna Connections Shoof Technologies Inc.
3. POWER CONNECTION Power connection can be applied to the Strix V3 via the power port according to the following table and figure: Table 2 – Power Connections Port Function Board symbol J1 V+ + J2 GND GND VOLTAGE LIMITATION: J1 (V+) Function Maximum Minimum Supply voltage @ J1, J2 3.6V 3.3V J2 (GND) Figure 5 - Power Connections 4. LABELING The Strix V3 has two labels relevant to final assembly and RMA – the FCC/regulatory label and the Shoof Strix MAC Address label.
FCC ID: XXXXX IC: XXXXX This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Figure 6 - Sample FCC ID Label The barcode below an example of the Strix MAC address label that can be found in the location indicated in Figure 7. The barcode format is Code 3 of 9.
Regulatory label location Figure 8 - Top Side of Strix V3 Shoof Technologies Inc.
5. MODULE SPECIFICATION i. ii. Physical specification Parameter Value Size (mm) 92x34x19 Weight (g) 28 Electrical Specification Parameter Value Operating Frequencies 433MHz, 870-875.6MHz, 902928MHz, 2.4GHz Max output power 0dBm 433MHz +27dBm 902-928MHz +20dBm 2.4GHz Voltage Supply iii. iv. Notes 3.3V-3.
6. FCC AND INDUSTRY CANADA GOVERNMENT GUIDELINES FCC ID: XXXX IC: XXXXX Modifications (15.21) Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Part 15 Certification Notice (15.19(a)(3)) and RSS-GEN This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2.
brouillage est susceptible d’en compromettre le fonctionnement. L’antenne de cet émetteur ne doit pas se trouver à proximité de ou fonctionner en association avec une autre antenne ou un autre émetteur. Lʹappareil doit être installé de telle sorte que les gens ne viendront pas au sein de 20 cm (8 in.) de lʹantenne. Les changements ou modifications apportés sans l’approbation expresse de l’autorité responsable de la conformité pourront entraîner l’annulation de l’autorisation d’utilisation de cet équipement.
exigences en matière d’étiquetage pour un dispositif hôte intégrant un module radio. Le dispositif hôte doit être correctement étiqueté afin d’identifier les modules qu’il comprend. L’étiquette de certification Industrie Canada d’un module doit toujours être bien visible lors de l’installation sur un dispositif hôte.
Radio transmissions from the Strix tag are governed in the US by FCC Part 15 rules, and in Canada by corresponding Industry Canada regulation RSS-210 . Still other regulations apply in Europe and other countries. The Strix is shipped with the default mode of operation corresponding to FCC 15.231 disabled. The Strix tag can be configured for operation under this rule only by a provisioning through the Shoof provisioning tool.
FCC RFID REGISTRATION FORM FOR FCC RULE 15.240 To: Experimental Licensing Branch, OET Federal Communications Commission 445 12th Street, SW Washington, DC 20554 ATTN: RFID Registration Subject: Registration for Shoof Technologies, Inc. Model STRIX3 Tag The following information concerning the end user and installation location is hereby submitted as required by FCC Rule 15.
7. REGULATORY APPROVALS Japanese Type Approval Strix V3 complies with the Japanese radio law and is certified according to ARIB STD-T108. When the product is placed on the Japanese market, it must carry the Specified Radio Equipment marking as shown below: If the certification label cannot be recognized from outside (e.g. installation in a host) appropriate information must be referenced in the user manual.
