READ THIS FIRST Model W1755S ***IMPORTANT UPDATE*** Applies to Models Mfd. Since 04/15 and Manual Insert Revised 05/08 Phone #: (360) 734-3482 • Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz We made the following changes to this machine since the manual insert was printed: • Changed spiral cutterhead and indexable inserts. Aside from the information contained in this update, all other content in the owner's manual is applicable and MUST be read and understood for your own safety.
READ THIS FIRST Model W1755/W1755S ***IMPORTANT UPDATE*** Applies to Models Mfg. Since 7/12 and Owner's Manual April, 2007 Phone #: (360) 734-3482 • Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz The following changes were recently made to these machines since the owner's manual was printed: • • Now certified to meet CSA 22.2 #71.2-8 and UL 987-7th standards. Changed the motor nominal voltage from 110V/220V to 120V/240V.
ng f . y ed me o oss Model W1755/W1755S (Mfg. Since 7/12) SAFETY For Your Own Safety, Read Manual Before Operating Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below.
Model W1755/W1755S (Mfg. Since 7/12) WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. FORCING MACHINERY. Do not force machine. It will do the job safer and better at the rate for which it was designed. NEVER STAND ON MACHINE.
Model W1755/W1755S (Mfg. Since 7/12) Additional Safety for Jointers JOINTER INJURY RISKS. Familiarize yourself with the main injury risks associated with jointers— always use common sense and good judgement to reduce your risk of injury. Main injury risks from jointers: amputation/lacerations from contact with the moving cutterhead, entanglement/crushing injuries from getting caught in moving parts, blindness or eye injury from flying wood chips, or impact injuries from workpiece kickback.
Model W1755/W1755S (Mfg. Since 7/12) ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power.
Model W1755/W1755S (Mfg. Since 7/12) Grounding Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipmentgrounding wire.
JkXik :XgXZ`kfi *''D=; (),M8: Model W1755/W1755S (Mfg. Since 7/12) MOTOR (Pre-wire Ile :XgXZ`kfi +'D=; ),'M8: Voltage Conversion The voltage conversion MUST be performed by an electrician or qualified service personnel. ) + The voltage conversion procedure consists of rewiring the motor and installing the correct plug. A wiring diagram is provided on Page 8 for your reference.
Model W1755/W1755S (Mfg. Since 7/12) 120V Wiring Diagram N8IE@E> J?F:B ?8Q8I; ;`jZfee\Zk gfn\i Y\]fi\ nfib`e^ fe n`i`e^% E\lkiXc ?fk JkXik :XgXZ`kfi *''D=; (),M8: MOTOR (Pre-wired) Ile :XgXZ`kfi +'D=; ),'M8: 120 VAC 5-15 Plug >ifle[ KI8KJ ) * + SWITCH ( (viewed from behind) GFKJ >ifle[ >ifle[ 240V Wiring Diagram WARNING! SHOCK HAZARD! Disconnect power before working on wiring.
Model W1755S 6" Parallelogram Jointer with Spiral Cutterhead Manual Insert Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz The Model W1755S is the same as the Model W1755, except it has a spiral cutterhead. Besides the data sheet and parts in this insert, the content in the Model W1755 owner's manual is the same for both machines.
W1755S 6" Parallelogram Jointer with Spiral Cutterhead MODEL W1755S 6" PARALLELOGRAM JOINTER WITH SPIRAL CUTTERHEAD Product Dimensions Weight.......................................................................................................... 325 lbs. Width (side‐to‐side) x Depth (front‐to‐back) x Height........................ 55‐1/2 x 24‐1/2 x 47‐3/4 in. Footprint (Length x Width)......................................................................... 27 x 20‐1/2 in.
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Main Specifications Main Specifications Bevel Jointing................................................................................. 0 – 45 deg. L/R Maximum Width of Cut................................................................................... 6 in. Maximum Depth of Cut................................................................................ 1/8 in. Minimum Workpiece Length..............................................................
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Stand Breakdown 31 3 2 4 1 28-1 5 28-3 28-2 28-4 36 6 7 28-7 28-5 28-6 30 29 23 28 22 8 9 21 10 19 17 11 12 42 13 16 14 15 62 43 61 60 45 57 56 46 55 54 47 48 59 58 44 49 53 52 51 50 -4- 26 25 24 20 18 27
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Stand Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28-1 28-2 X1755S001 X1755S002 X1755S003 X1755S004 X1755S005 X1755S006 X1755S007 X1755S008 X1755S009 X1755S010 X1755S011 X1755S012 X1755S013 X1755S014 X1755S015 X1755S016 X1755S017 X1755S018 X1755S019 X1755S020 X1755S021 X1755S022 X1755S023 X1755S024 X1755S025 X1755S026 X1755S027 X1755S028 X1755S028-1 X1755S028
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Jointer Breakdown 221 101 102 106 107 105 103 104 109 112 123 121 120 140 141 128 145 223 224 225 239 235 234 233 238 237 236 229 146 123 232 124 230 231 143 144 142 147 115 116 117 148 173 175 218 219 220 137 136 138 119 113 114 135 124 139 118 122 222 133 134 129 130 131 125 132 126 108 127 172 174 177 178 179 171 170 169 153 163 165 161 168 156 167 159 191 194 193 151 155 182 181 162 180 183 185 150 149
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Jointer Parts List REF PART # DESCRIPTION REF PART # DESCRIPTION 101 102 103 104 105 106 107 108 109 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 X1755S101 X1755S102 X1755S103 X1755S104 X1755S105 X1755S106 X1755S107 X1755S108 X1755S109 X1755S112 X1755S113 X1755S114 X1755S115 X1755S116 X1755S117 X1755S118 X1755S119 X1
W1755S 6" Parallelogram Jointer with Spiral Cutterhead Jointer Parts List, cont. REF PART # DESCRIPTION REF PART # DESCRIPTION 213 214 215 216 217 218 219 220 221 222 223 224 X1755S213 X1755S214 X1755S215 X1755S216 X1755S217 X1755S218 X1755S219 X1755S220 X1755S221 X1755S222 X1755S223 X1755S224 LEVER HANDLE CAP SCREW M8-1.25 X 40 CLAMP PLATE MEDIUM ADJUSTMENT SCR PUSH BLOCK OPEN END WRENCH 8/10MM OPEN END WRENCH 12/14MM HEX WRENCH 2.
READ THIS FIRST Model W1755/W1755S ***IMPORTANT UPDATE*** Applies to Models Mfg. Since 7/12 and Owner's Manual April, 2007 Phone #: (360) 734-3482 • Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz The following changes were recently made to these machines since the owner's manual was printed: • • Now certified to meet CSA 22.2 #71.2-8 and UL 987-7th standards. Changed the motor nominal voltage from 110V/220V to 120V/240V.
ng f . y ed me o oss Model W1755/W1755S (Mfg. Since 7/12) SAFETY For Your Own Safety, Read Manual Before Operating Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below.
Model W1755/W1755S (Mfg. Since 7/12) WEARING PROPER APPAREL. Do not wear clothing, apparel, or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. FORCING MACHINERY. Do not force machine. It will do the job safer and better at the rate for which it was designed. NEVER STAND ON MACHINE.
Model W1755/W1755S (Mfg. Since 7/12) Additional Safety for Jointers JOINTER INJURY RISKS. Familiarize yourself with the main injury risks associated with jointers— always use common sense and good judgement to reduce your risk of injury. Main injury risks from jointers: amputation/lacerations from contact with the moving cutterhead, entanglement/crushing injuries from getting caught in moving parts, blindness or eye injury from flying wood chips, or impact injuries from workpiece kickback.
Model W1755/W1755S (Mfg. Since 7/12) ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power.
Model W1755/W1755S (Mfg. Since 7/12) Grounding Requirements This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipmentgrounding wire.
JkXik :XgXZ`kfi *''D=; (),M8: Model W1755/W1755S (Mfg. Since 7/12) MOTOR (Pre-wire Ile :XgXZ`kfi +'D=; ),'M8: Voltage Conversion The voltage conversion MUST be performed by an electrician or qualified service personnel. ) + The voltage conversion procedure consists of rewiring the motor and installing the correct plug. A wiring diagram is provided on Page 8 for your reference.
Model W1755/W1755S (Mfg. Since 7/12) 120V Wiring Diagram N8IE@E> J?F:B ?8Q8I; ;`jZfee\Zk gfn\i Y\]fi\ nfib`e^ fe n`i`e^% E\lkiXc ?fk JkXik :XgXZ`kfi *''D=; (),M8: MOTOR (Pre-wired) Ile :XgXZ`kfi +'D=; ),'M8: 120 VAC 5-15 Plug >ifle[ KI8KJ ) * + SWITCH ( (viewed from behind) GFKJ >ifle[ >ifle[ 240V Wiring Diagram WARNING! SHOCK HAZARD! Disconnect power before working on wiring.
MODEL W1755 6" PARALLELOGRAM JOINTER OWNER'S MANUAL Phone: (360) 734-3482 • On-Line Technical Support: tech-support@shopfox.biz COPYRIGHT © MARCH, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED APRIL, 2007. #9160TR WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ����������������������������������������������������������������������� ������������������������������������������������������������������������ �������������������������������������������������������������������
SAFETY................................................ 5 Standard Safety Instructions ................... 5 Additional Safety Instructions for Jointers... 7 Avoiding Potential Injuries ..................... 8 PARTS ................................................44 Stand Breakdown ................................44 Stand Parts List ..................................45 Jointer Breakdown ..............................46 Jointer Parts List ................................47 Labels/Cosmetic Parts .............
INTRODUCTION W1755 6" Parallelogram Jointer INTRODUCTION Woodstock Technical Support Your new SHOP FOX® 6" Parallelogram Jointer has been specially designed to provide many years of trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation. Woodstock International, Inc. is committed to customer satisfaction.
MACHINE SPECIFICATIONS Phone #: (360) 734-3482 • Online Tech Support: tech-support@shopfox.biz • Web: www.shopfox.biz MODEL W1755 6" PARALLELOGRAM JOINTER Motor Type ......................................................................................... TEFC Capacitor Start Induction Horsepower .............................................................................................................. 11⁄2 HP Phase / Voltage ..............................................................................
INTRODUCTION W1755 6" Parallelogram Jointer Controls and Features B D C A E F K G J H L M I A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S.
W1755 6" Parallelogram Jointer SAFETY Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury.
W1755 6" Parallelogram Jointer 10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power OFF and allow all moving parts to come to a complete stop before leaving machine unattended. SAFETY 11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or where any flammable or noxious fumes may exist. 12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents. 13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE.
W1755 6" Parallelogram Jointer Additional Safety Instructions for Jointers USE this and other machinery with caution and respect. Always consider safety first, as it applies to your individual working conditions. No list of safety guidelines can be complete—every shop environment is different. Failure to follow guidelines could result in serious personal injury, damage to equipment or poor work results. 1. JOINTER KICKBACK.
W1755 6" Parallelogram Jointer SAFETY Avoiding Potential Injuries Figure 1. Correct operator and workpiece position, guard is in place, and push blocks are being used. Figure 2. Never surface plane without push blocks! Figure 4. Never stand directly behind the workpiece! Figure 3. Never plane/edge-joint with the guard removed! Figure 5.
W1755 6" Parallelogram Jointer ELECTRICAL 110V/220V Operation ELECTRICAL The Model W1755 is prewired for 110V operation, but you can rewire it for 220V operation (refer to the wiring diagram on Page 41). We recommend connecting this machine to a dedicated circuit with a verified ground, using the circuit size given below. Never replace a circuit breaker with one of higher amperage without consulting a qualified electrician to ensure compliance with wiring codes.
W1755 6" Parallelogram Jointer SETUP Unpacking The SHOP FOX® Model W1755 has been carefully packaged for safe transporting. If you notice the machine has been damaged, please contact your authorized SHOP FOX® dealer immediately. SUFFOCATION HAZARD! SETUP Immediately discard all plastic bags and packing materials to eliminate suffocation hazards for children and animals.
W1755 6" Parallelogram Jointer Inventory The following is a description of the items shipped with the SHOP FOX® Model W1755. Note: If you can't find an item on this list, check the mounting location on the machine or examine the packaging materials carefully. Occasionally we pre-install certain components for safer shipping. Qty Box 2: (Figure 8) L. Stand Assembly w/Motor .................................1 M. Pedestal Switch ............................................1 N. Wheel Assembly .................
W1755 6" Parallelogram Jointer SETUP Machine Placement • Floor Load: This machine distributes a heavy load in a small footprint. Some residential floors may require additional bracing to support both machine and operator. • Working Clearances: Consider existing and anticipated needs, size of material to be processed through the machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your Jointer.
W1755 6" Parallelogram Jointer Assembly To assemble the jointer, do these steps: 1. Carefully lay the stand on its side so you can access the underside. 2. Use the M8-1.25 x 50 hex bolt and 8mm flat washer to bolt the wheel assembly to the stand, as shown in Figure 9. 3. Use the two M10-1.5 x 55 hex bolts, 10mm flat washers, and M10-1.5 hex nuts to finish tightening the wheel assembly to the stand, as shown in Figure 10. 4. Turn the stand rightside up and remove the back cover. Figure 9.
W1755 6" Parallelogram Jointer 7. Loosen the motor bracket bolts shown by the black arrows in Figure 12. 8. Put the V-belt on the motor pulley, then roll it onto the cutterhead pulley, as shown in Figure 13. 9. Check the alignment of the pulleys to make sure the V-belt is straight up and down. — If the pulleys are aligned, go to Step 13. — If the pulleys are NOT aligned, follow Steps 10– 12. 10. Remove the V-belt and loosen the motor mount bolts shown by the white arrows in Figure 12. SETUP 11.
W1755 6" Parallelogram Jointer 15. Install the belt guard with the two M6-1 x 10 flange bolts, M6-1 hex nuts, and 6mm flat washers, as shown in Figure 15. Belt Guard The belt guard MUST be installed or the moving Vbelt will be exposed, creating an entanglement hazard at the back of the jointer. 16. Replace the cover on the back of the jointer stand. 17. Use the two M6-1 x 20 cap screws to attach the extension table to the front of the jointer, as shown in Figure 16. Leave the cap screws loose for now.
W1755 6" Parallelogram Jointer 21. Attach the carriage to the back of the jointer with the M10-1.5 x 30 cap screw on the infeed side, the M10-1.5 x 50 cap screw on the outfeed side, and two 10mm flat washers. Leave the cap screws loose for now. Paper 22. Place three pieces of paper on the jointer bed, slide the top half of the carriage over the paper, and allow it to rest on the paper, as shown in Figure 18.
W1755 6" Parallelogram Jointer 29. Test that the cutterhead guard is working correctly by pulling it back and letting go. The cutterhead guard should quickly spring back over the cutterhead when you do this. — If the guard does not quickly spring back over the cutterhead when you perform this test, then remove it and repeat Steps 27–29. Do not continue with the assembly until the cutterhead guard works correctly. 30. Use the two M10-1.
W1755 6" Parallelogram Jointer Test Run Complete this process once you have familiarized yourself with all instructions in this manual. To test run the jointer, do these steps: SETUP 1. Read the entire owner's manual first to make sure you are familiar with the safety and operation controls of this machine! 2. Make sure all tools and foreign objects have been removed from the machine. 3. Review Page 9 and connect your machine to the power source. 4.
W1755 6" Parallelogram Jointer OPERATIONS General The Model W1755 will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine.
W1755 6" Parallelogram Jointer Basic Controls This section covers the basic controls used during routine operations. START Button ON/OFF Switch (Figure 26): Starts and stops the motor. After the OFF paddle is pushed, the switch may need to be reset before the next operation by lifting the paddle and fully depressing the STOP button. Table Movement: To move the infeed table, loosen the table lock (Figure 27), move the table with the table lever, then tighten the table lock.
W1755 6" Parallelogram Jointer Stock Inspection & Requirements Here are some rules to follow when choosing and jointing stock: ������� �������������� �������� • • • DO NOT joint or surface plane stock that contains loose knots. Injury to the operator or damage to the workpiece can occur if the knots become dislodged during the cutting operation. ������������� ���������� ��������� DO NOT joint or surface plane against the grain direction.
W1755 6" Parallelogram Jointer Squaring Stock Squaring stock involves four steps performed in the order below: 1. Surface Plane on the Jointer: The concave face of the workpiece is surface planed flat with the jointer (Figure 32). 2. Surface Plane on a Thickness Planer: The opposite face of the workpiece is surface planed flat with a thickness planer (Figure 33). 3. Edge Joint on the Jointer: The concave edge of the workpiece is jointed flat with the jointer (Figure 34).
W1755 6" Parallelogram Jointer Surface Planing The purpose of surface planing on the jointer is to make one flat face on a piece of stock (see Figures 36 & 37) to prepare it for surface planing on a thickness planer. NOTICE If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation.
W1755 6" Parallelogram Jointer Edge Jointing The purpose of edge jointing is to produce a finished, flat-edged surface (see Figures 38 & 39) that is suitable for joinery or finishing. It is also a necessary step when squaring rough or warped stock. NOTICE If you are not experienced with a jointer, set the depth of cut to 0", and practice feeding the workpiece across the tables as described below. This procedure will better prepare you for the actual operation. Figure 38. Typical edge jointing operation.
W1755 6" Parallelogram Jointer Bevel Cutting The purpose of bevel cutting is to cut a specific angle into the edge of a workpiece (see Figures 40 & 41). The Model W1755 has preset fence stops at 45˚ inward, 90˚, and 45˚ outward (135˚). If your situation requires a different angle, the preset fence stops can be easily adjusted for your needs. To bevel cut on the jointer, do these steps: 1. Read and understand SAFETY, beginning on Page 5. 2.
W1755 6" Parallelogram Jointer Rabbet Cutting Rabbet cuts remove a section of the workpiece edge (see Figures 42 & 43). When combined with another rabbet cut edge, the rabbet joints create a simple, yet strong method of joining stock. Often, rabbet cuts must be made in multiple passes to acheive the desired depth. NOTICE If you are not experienced with a jointer, set the depth of cut to zero, and practice feeding the workpiece across the tables as described below.
W1755 6" Parallelogram Jointer MAINTENANCE General Regular periodic maintenance on your SHOP FOX® Model W1755 will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: • • • • • • Loose mounting bolts. Worn switch. Worn or damaged cords and plugs. Damaged V-belt. Damaged or loose knives. Any other condition that could hamper the safe operation of this machine.
W1755 6" Parallelogram Jointer SERVICE General This section covers the most common service adjustments or procedures that may need to be made during the life of your machine. If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.
W1755 6" Parallelogram Jointer Adjusting/Replacing Knives Setting the knives correctly is crucial to the proper operation of the jointer and is very important in keeping the knives sharp. If one knife is higher than the others, it will do the majority of the work, and thus, dull much faster than the others. There are two options for setting the knives—the straightedge method and the knife setting jig method.
W1755 6" Parallelogram Jointer The Model W1755 comes with both jack screws and springs inside the cutterhead to provide two options for adjusting the knives (see Figure 46). Note: Only one of these options is needed to set the knives—Step 5 gives the details. To adjust/replace the knives, do these steps: 1. DISCONNECT JOINTER FROM POWER SOURCE! 2. Remove the cutterhead guard from the table and move the fence back as far as it will go. 3. Open the back cover to expose the cutterhead pulley. 4.
W1755 6" Parallelogram Jointer 7. Adjusting the knife heights: Jack Screws: Using a 3mm hex wrench, find the jack screws through the access holes in the cutterhead (Figure 48) and rotate the jack screws to raise or lower the knife. When the knife is set correctly, it will barely touch the bottom of the straightedge or the knife setting jig middle pad. Snug the gib bolts tight enough to just hold the knife in place.
W1755 6" Parallelogram Jointer Checking/Adjusting Table Parallelism If the tables are not parallel with the cutterhead or each other, then poor cutting results and kickback may occur. Checking Outfeed Table To check the outfeed table parallelism, do these steps: 1. DISCONNECT JOINTER FROM POWER SOURCE! 2. Remove the cutterhead guard and fence. 3.
W1755 6" Parallelogram Jointer 3. Place the straightedge halfway across the infeed table and halfway over the outfeed table, and adjust the infeed table even with the outfeed table, as shown in Figure 53. 4. Place the straightedge in the positions shown in Figure 54. In each position, the straightedge should sit flat against both the outfeed table and the infeed table. — If the straightedge sits flat against both the infeed and outfeed table, then the tables are parallel.
W1755 6" Parallelogram Jointer SERVICE To adjust the table parallelism, do these steps: Location of Stacked Set Screws 1. DISCONNECT JOINTER FROM POWER SOURCE! 2. Remove the cutterhead guard and fence. 3. Place the straightedge on the outfeed table so it hangs over the cutterhead, and lower the outfeed table until the straightedge just touches the cutterhead body, as shown in Figure 51. 4.
W1755 6" Parallelogram Jointer Setting Outfeed Table Height The outfeed table height must be even with the cutterhead knives at top dead center. If the outfeed table is set too low, there will be snipe. If the outfeed table is set too high, the workpiece will hit the edge of the outfeed table during operation, increasing the chance of kickback. Setting the outfeed table requires some type of feeler gauge to get the height correct. Because a 0.
W1755 6" Parallelogram Jointer Setting Infeed Table Height The infeed table on the Model W1755 has positive stop bolts that, when properly set up, allow the operator to quickly adjust the infeed table between finish/final cuts (top height) and shaping/heavy cuts (bottom height). Jam Nuts Top Height We recommend setting the minimum depth of cut to 1/32" and the maximum depth of cut to 1/8" for most operations.
W1755 6" Parallelogram Jointer Setting Fence Stops The fence stops simplify the task of adjusting the fence to 45˚ inward, 90˚, and 45˚ outward (135˚). To set the 45˚ inward fence stop, do these steps: 1. Tilt the fence approximately 45° inward (Figure 60) onto the positive stop bolts, using a 45° square as a gauge. 2. Loosen the jam nut on the 45° inward positive stop bolt shown in Figure 60. 3.
W1755 6" Parallelogram Jointer V-Belt Replacement Inspect the V-belt closely; if you notice fraying, cracking, glazing, or any other damage, replace the belt. A worn or damaged V-belt will not provide optimum power transmission from the motor to the cutterhead. Overly loose V-belts can slip on the pulleys and burn up or cause poor machine performance. Overly tight V-belts cause unecessary wear on the motor and pully bearings, leading to a shortened lifespan. To replace the V-belts, do these steps: 1.
W1755 6" Parallelogram Jointer Pulley Alignment Pulley alignment is another important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplanar) for optimum performance. Each pulley can be adjusted by loosening the motor mount bolts, sliding the motor in or out, and retightening the fasteners to lock the motor pulley in place. To align the pulleys, do these steps: ���������� ������ ��������� ����� ������ 1.
W1755 6" Parallelogram Jointer Electrical Components Figure 69. Motor wired for 110V. Figure 71. Motor wired for 220V. ON Switch OFF Switch Figure 72. Motor capacitors. SERVICE Figure 70. ON/OFF Switch.
Wiring Diagram W1755 6" Parallelogram Jointer 110V Wiring Diagram �������� ������������� ����������������� ������������������ ������� ������� See Figure 72 ����� ��������� ������ ������ ��� ��� ��������� ����� ������ ����� ������� ������ ����� � ������ � � � �������������������� See Figure 70 ���� ������ ������ See Figure 69 220V Wiring Diagram �������� ������������� ����������������� ������������������ ������� ������ See Figure 72 ����� ��������� ������ ������ ��� ��������� ����� ������
W1755 6" Parallelogram Jointer Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING! DO NOT make any adjustments until power is disconnected and moving parts have come to a complete stop! Motor & Electrical PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Stop button depressed. 2. No power. 3. Open circuit in motor or loose connections. 1. Twist the stop button to allow it to pop out. 2. Check circuit breaker. 3.
W1755 6" Parallelogram Jointer Cutting PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION 1. Align outfeed table at top dead center of the Excessive snipe (gouge in 1. Outfeed table is set too low. the end of the board that cutterhead knives (Page 35). is uneven with the rest of 2. Operator pushing down on trailing 2. Reduce/eliminate downward pressure on that end of the cut). end of the workpiece. workpiece. Workpiece stops in the 1. Outfeed table is set too high. middle of the cut. 1.
W1755 6" Parallelogram Jointer PARTS Stand Breakdown �� � � � � ���� � ���� ���� ���� �� � � ���� ���� ���� �� �� �� �� �� � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� PARTS �� �� �� �� -44- �� �� �� �� �� ��
W1755 6" Parallelogram Jointer Stand Parts List REF PART�# DESCRIPTION REF PART�# DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 28-1 28-2 XPW02M X1755002 XPFS02M X1755004 X1755005 XPW03M XPN01M XPS40M XPW02M X1755010 XPN03M XPW01M X1755013 X1755014 XPB86M X1755016 X1755017 XPCB05 XPCB11 XPW07 XPFN02 X1755022 XPN08 XPVA40 X1755025 XPSS02M XPK12M X1755028 X1755028-1 X1755028-2 FLAT�WASHER�5MM PANEL FLANGE�SCREW�M6-1�X�12 BELT�GUARD CABINET�STAND FLAT�WASHER�6M
W1755 6" Parallelogram Jointer Jointer Breakdown ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ��� ���
W1755 6" Parallelogram Jointer Jointer Parts List REF PART�# DESCRIPTION REF PART�# DESCRIPTION 101 102 103 104 105 106 107 108 109 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 X1755101 X1755102 X1755103 X1755104 XPSS11M XPSS14M X1755107 XPN01M XPSB06M X1755112 X1755113 XPW06M XPN09M XPSB72M XPW04M XPSB24M X1755119 X1755120 XPW01M XPN03M X1755123 XPSB13M XPW03M X1755126 XPW03M XPSB115M X1755129
W1755 6" Parallelogram Jointer Jointer Parts List PART�# DESCRIPTION REF PART�# DESCRIPTION XPB02M XPW01M X1755202 X1755203 X1755204 XPSS14M X1755206 X1755207 X1755208 XPFH07M X1755210 X1755211 XPN09M X1755213 X1755214 XPSB12M X1755216 X1755217 X1755218 X1755219 HEX�BOLT�M6-1�X�12 FLAT�WASHER�8MM ADJUSTABLE�HANDLE ECCENTRIC�BUSHING TABLE�SHAFT SET�SCREW�M8-1.25�X�12 TABLE�SHAFT POINTER LEVER FLAT�HD�SCR�M5-.8�X�10 PIVOT�BRACKET ADJUSTING�BLOCK HEX�NUT�M12-1.75 LEVER HANDLE CAP�SCREW�M8-1.
W1755 6" Parallelogram Jointer Labels/Cosmetic Parts Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again.
Warranty Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc.
W1755 6" Parallelogram Jointer Warranty Registration Name ___________________________________________________________________________________ Street __________________________________________________________________________________ City _________________________ State ___________________________Zip ________________________ Phone # ______________________ Email __________________________Invoice # ___________________ Model #_________Serial #______________Dealer Name__________________Purchase Date___________
FOLD ALONG DOTTED LINE Place Stamp Here WOODSTOCK INTERNATIONAL INC. P.O.
