READ THIS FIRST Model W1765 ***IMPORTANT UPDATE*** Applies to Models Mfd. Since 11/16 and Owner's Manual Revised 04/14 Phone #: (360) 734-3482 • Tech Support: techsupport@woodstockint.com • Web: www.woodstockint.com We made the following changes to this machine since the manual was printed: • Redesigned stand column shafts, column caps, and various related hardware (see below).
MODEL W1765 1/4 HP POWER FEEDER OWNER'S MANUAL (FOR MODELS MANUFACTURED SINCE 5/14) Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz COPYRIGHT © JULY, 2007 BY WOODSTOCK INTERNATIONAL, INC. REVISED APRIL, 2014 (TS) WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC. #9706CR Printed in Taiwan V2.04.
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death. The owner of this machine/tool is solely responsible for its safe use.
INTRODUCTION...................................................................................................2 Woodstock Technical Support............................................................................. 2 OPERATIONS.................................................................................................... 17 General..................................................................................................... 17 Changing Feed Speed..............................................
INTRODUCTION Model W1765 (For Machines Mfd. Since 5/14) INTRODUCTION Woodstock Technical Support Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to include the basic information for safety, setup, operation, maintenance, and service of this product. In the event that questions arise about your machine, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz.
MACHINE SPECIFICATIONS Phone #: (360) 734–3482 • Online Tech Support: tech–support@shopfox.biz • Web: www.shopfox.biz MOdEl W1765 1/4 HP POWER FEEdER Motor Type .......................................................................................... TEFC Capacitor Start Induction Horsepower .............................................................................................................. 1/4 HP Voltage ...........................................................................................
INTRODUCTION Model W1765 (For Machines Mfd. Since 5/14) Shipping Dimensions Type ................................................................................................................... Cardboard Content ................................................................................................................. Machine Weight .................................................................................................................... 80 lbs. Length/Width/Height ......................
INTRODUCTION Model W1765 (For Machines Mfd. Since 5/14) Controls and Features Vertical Travel Handcrank Elbow Joint Lock Lever ⁄4 HP Motor 1 Horizontal Travel Lock Lever Horizontal Handcrank Gearbox Oil Port Vertical Travel Lock Lever Rotary Movement Lock Lever Elbow Joint Lock Lever Figure 1. Controls and Features.
Model W1765 (For Machines Mfd. Since 5/14) SAFETY SAFETY For.Your.Own.Safety, Read.Manual.Before.Operating.Machine The. purpose. of. safety. symbols. is. to. attract. your. attention. to. possible. hazardous. conditions.. This. manual.uses.a.series.of.symbols.and.signal.words.intended.to.convey.the.level.of.importance.of.the. safety.messages..The.progression.of.symbols.is.described.below..Remember.that.safety.messages.by. themselves. do. not. eliminate. danger. and. are. not. a. substitute. for. proper.
Model W1765 (For Machines Mfd. Since 5/14) FORCING.MACHINERY..Do not force machine. It will do the job safer and better at the rate for which it was designed. NEVER.STAND.ON.MACHINE..Serious injury may occur if machine is tipped or if the cutting tool is unintentionally contacted. HAZARDOUS.DUST..Dust created while using machinery may cause cancer, birth defects, or long-term respiratory damage.
Model W1765 (For Machines Mfd. Since 5/14) SAFETY Additional Safety for Power Feeders MAIN.INJURY.HAZARDS:.Death,.amputation,.or.crushing.injuries.from.getting.entangled.in. moving.parts—which.may.include.being.pulled.into.the.cutting.tool.on.attached.machinery;. death,.blindness,.broken.bones,.or.bruises.from.being.struck.by.an.ejected.workpiece. (kickback)..To.minimize.your.risk.of.these.hazards,.always.heed.the.following.information: ATTACHED.MACHINERY.
Model W1765 (For Machines Mfd. Since 5/14) ELECTRICAL Circuit Requirements This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power. The. machine. must. be. properly. set. up. before. it. is. safe. to. operate.. DO. NOT. connect.
Model W1765 (For Machines Mfd. Since 5/14) Grounding Requirements ELECTRICAL This machine MUST be grounded. In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. The wire with green insulation (with/without yellow stripes) is the equipmentgrounding wire.
Model W1765 (For Machines Mfd. Since 5/14) SETUP Unpacking This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. Inventory The following is a description of the main components shipped with the Model W1765. Lay the components out to inventory them. Keep machine disconnected from power until instructed otherwise. Qty Box Inventory (see Figures 3 & 4) A. Elbow Joint Assembly.
Model W1765 (For Machines Mfd. Since 5/14) Cleaning Machine To prevent corrosion during shipment and storage of your machine, the factory has coated the bare metal surfaces of your machine with a heavy-duty rust prevention compound. If you are unprepared or impatient, this compound can be difficult to remove.
Model W1765 (For Machines Mfd. Since 5/14) Assembly To correctly position this power feeder on your table top, assemble the power feeder first (see Figure 5), then refer to Base Mounting on Page 15. With the power feeder unit completely assembled, it will be easier to determine where on the table top to drill your base mounting holes, so you can take advantage of the full range of power feeder swing and adjustments.
Model W1765 (For Machines Mfd. Since 5/14) Base Mounting Assemble the power feeder before you mount the base to determine where on the table top to drill your base mounting holes, so you can maximize power feeder swing and adjustment options. There are three mounting options available, Through Bolt Mounting, Direct Mounting, and Quick Holder Mounting options discussed on Page 15. Choose an option that suits your requirements.
Model W1765 (For Machines Mfd. Since 5/14) Through-Bolt Mounting We recommend that you mount your new power feeder to the machine table using the included M10-1.5 x 50 hex bolts and lock washers, plus additional flat washers and locking hex nuts for a through-bolt setup (see Figure 8). This option will give the most rigidity and clamping strength to prevent the feeder base from twisting out of alignment during use.
Model W1765 (For Machines Mfd. Since 5/14) Test Run Once power feeder assembly is complete and mounted on the table, you must test run your power feeder to make sure it runs properly. If, during the test run, you cannot easily locate the source of an unusual noise or vibration, stop using the power feeder immediately, then review the Troubleshooting table on Page 23. If you still cannot remedy a problem, contact our Technical Support at (360) 734-3482 for assistance.
Model W1765 (For Machines Mfd. Since 5/14) OPERATIONS General This machine will perform many types of operations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly. The instructions in this section are written with the understanding that the operator has the necessary knowledge and skills to operate this machine.
Model W1765 (For Machines Mfd. Since 5/14) Changing Feed Speed Your power feeder has the option to feed a workpiece at six different feed rates: 13, 20, 26, 33, 43, and 62 feet per minute. These rates are achieved by changing the combination of change gears in the power feeder gear box. To change the feed rate of your power feeder, do these steps: 1. DISCONNECT THE MACHINE FROM POWER! 2. Make sure the speed dial is pointing to the OFF position. 3.
Model W1765 (For Machines Mfd. Since 5/14) Power Feeder Accessories The following power feeder accessories may be available through your local Woodstock International Inc. Dealer. If you do not have a dealer in your area, these products are also available through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at: 1-800-840-8420 or at sales@woodstockint.com.
Model W1765 (For Machines Mfd. Since 5/14) The Model D3096 Shop Fox Featherboard helps reduce the risk of kick-back and achieve consistent results. Designed to lock into standard 3⁄8" x 3⁄4" miter gauge slots, this Featherboard is adjustable for various stock widths and miter slot locations. No drilling or bulky clamp arrangements! D3096 The Model D2018 60-Pc. Tap & Die Set includes both coarse and fine thread tap and dies.
Model W1765 (For Machines Mfd. Since 5/14) MAINTENANCE General Regular periodic maintenance on your machine will ensure its optimum performance. Make a habit of inspecting your machine each time you use it. Check for the following conditions and repair or replace when necessary: • • • Loose mounting bolts and damaged wheel rubber. Worn or damaged, switch, cord, and plug. Any other condition that could hamper the safe operation of this power feeder.
Model W1765 (For Machines Mfd. Since 5/14) SERVICE General This section covers the most common service adjustments or procedures that may need to be made during the life of your machine. If you require additional machine service not included in this section, please contact Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.biz. Wheel Replacement If you damage one or more wheels, you can easily replace the wheels.
Model W1765 (For Machines Mfd. Since 5/14) Troubleshooting This section covers the most common problems and corrections with this type of machine. WARNING! DO NOT make any adjustments until power is disconnected and moving parts have come to a complete stop! PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Motor will not start. 1. Low voltage. 2. Open circuit in motor or loose connections. 3. Faulty start capacitor. 1. Check power supply for proper voltage. 2.
Model W1765 (For Machines Mfd. Since 5/14) Electrical Safety Instructions These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Study this diagram carefully. If you notice differences between your machine and these wiring diagrams, call Woodstock International Technical Support at (360) 734-3482. SHOCK.HAZARD. Working on wiring that is connected to a power source is extremely dangerous.
Model W1765 (For Machines Mfd. Since 5/14) Wiring Diagram Read Page 24 Motor Power and Direction Switch Side A Side B STOP Before Wiring 3 4 1 2 7 8 5 6 11 12 9 10 2 3 6 Motor Ground Run Capacitor Ground Neutral Hot 120 VAC Ground 5-15 Plug SHOCK HAZARD! Disconnect power before servicing electrical parts. Touching electrified parts will result in severe burns, electrocution, or death. Figure 17. Motor power and direction switch. -25- SERVICE Figure 16. Motor capacitor.
Model W1765 (For Machines Mfd.
Model W1765 (For Machines Mfd.
Model W1765 (For Machines Mfd.
Model W1765 (For Machines Mfd. Since 5/14) Labels & Cosmetics Safety labels warn about machine hazards and how to prevent serious personal injury. The owner of this machine MUST maintain the original location and readability of all labels on this machine. If any label is removed or becomes unreadable, REPLACE that label before allowing machine to be operated again. Contact us at (360) 734-3482 or www.shopfoxtools.com to order new labels.
Model W1765 (For Machines Mfd.
Model W1765 (For Machines Mfd.
Fold along dotted lIne place stamp Here Woodstock international inc. p.o.
WARRANTY WARRANTY Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship and materials for a period of two years from the date of original purchase by the original owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or reimbursement of third party expenses incurred. Woodstock International, Inc.
High Quality Machines and Tools Woodstock International, Inc. carries thousands of products designed to meet the needs of today's woodworkers and metalworkers.
