GMP ISO9001 ISO14001 ISO13485 CERTIFIED MEDICAL POWER WHEELCHAIR User Manual WIZZ 888WNL STREAMER 888WB STREAMER 888WAB STREAMER 888WSB JETSTREAM-M 888WAM JETSTREAM-L 888WAL
GMP ISO9001 ISO14001 ISO13485 CERTIFIED CONTENTS INTRODUCTION page 3 FEATURE GUIDE page 3 --5 EMI WARNING page 6 – 7 SAFETY INSTRUCTIONS page 8 -- 9 WARNING, CAUTION AND INDICATION LABEL LOCATION page 10 -- 12 PREPARATION FOR USE page 13 -- 14 ADJUSTMENT PROCEDURES page 15 – 17 OPERATION INSTRUCTIONS page 18 – 19 DISASSEMBLY INSTRUCTIONS page 20 – 21 BATTERIES AND BATTERY CHARGING page 22 – 24 TROUBLESHOOTING page 25 -- 26 SPECIFICATION page 27 QUARTERLY INSPECTION page 28 DISCLAIME
GMP ISO9001 ISO14001 ISO13485 CERTIFIED INTRODUCTION Congratulations on your purchase of our product. This Powerchair is the ultimate combination of style and comfort. The short wheelbase allows easy maneuverability within the smallest spaces both in and outdoors. The middle/rear drive wheels and electromagnetic brakes provide a safe and comfortable ride. This manual contains important information regarding the safe use of the Powerchair.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED FEATURE GUIDE STREAMER (888WB/888WSB) (1) (7) Armrest (adjustable with selected width, length, angle and height) (2) Joystick Controller (3) Charging Port (4) Captain Seat Assembly (5) Footrest (adjustable with selected Front Castor (8”） (7) Headrest (adjustable with selected (4) (3) (8) (10) length and angle) (6) (1) (2) (9) (5) (11) height) (8) Backrest (adjustable with selected angle) (9) Seat Supporting Post (12) (6) Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED FEATURE GUIDE JEETSTREAM-M (888WAM) (1) Headrest (adjustable with selected (1) height) (2) (4) Backrest (adjustable with selected height) (3) Joystick Controller (4) Armrest (adjustable height, width and (2) (3) (10) angle selection) (5) On-Board Charger w/ retractable cord (6) Footrest (7) Front Castor (8) Rear Drive Wheel (9) Anti-Tip Wheel (6) (5) (9) (10) Reclining Pillow-Top Seat (7) (8) Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED EMI WARNING ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE SOURCES Medical Power Wheelchairs (Hereinafter referred to as “Powerchair”) may be susceptible to electromagnetic interference (EMI), which is a kind of interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV stations, amateur radio (HAM) transmitters, two-way radio, and cellular phones.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED EMI WARNING POWERCHAIR ELECTROMAGNETIC INTERFERENCE (EMI) Because EM energy rapidly becomes more intense as one moves closer to the transmitting antenna (source), the EM fields from hand-held radio sources (transceivers) are of special concern. It is possible to unintentionally bring high levels of EM energy very close to the Powerchair’s control system while using these devices. This can affect Powerchair movement and braking.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED SAFETY INSTRUCTIONS Please use your Powerchair often and let it expand your horizons. The more mobility your Powerchair brings, the happier we will be! But, with all things, observing a few rules will ensure safe maneuvering. So please… (1) Do not drive the Powerchair without reading this instruction manual. (2) Do not exceed the safe climbing maximum angle (Table 2). (3) Do not use the joystick in an erratic manner when going up or down an incline.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED SAFETY INSTRUCTIONS (20) Whenever a center bolt of the wheel assembly has been loosened, please replace a specified new bolt from authorized providers and secure with a torque of 240 ± 5 kg-cm together with Loc-tite 271 adhesive (or equivalent). (21) When proceeding up any incline, please move the seat to the most forward position or if you have the deluxe seat, make sure that it is in the 90 degree (upright) position.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED WARNING, CAUTION AND INDICATION LABEL LOCATION To ensure your safety and protect the Powerchair from damage, please find out and read the content of labels listed below before your first ride. Joystick Controller Fig. 4 Chassis Shroud of WIZZ (888WNL) or Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED WARNING, CAUTION AND INDICATION LABEL LOCATION Chassis Shroud of STREAMER (888WAB) or Fig. 6 Chassis Shroud of STREAMER (888WB/888WSB) or Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED WARNING, CAUTION AND INDICATION LABEL LOCATION Chassis Shroud of JETSTREAM-L/M (888WAL/888WAM) or YELLOW - CHARGING Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED PREPARATION FOR USE The Powerchair has many features designed to give the user maximum comfort. Adjustments can be made to the following parts of the Powerchair: (1) Footrest can be lengthened outward from the main frame in three positions. (2) Footrest angle can be adjusted from 00 to 600. (3) Armrests can be set at different angles. (4) Armrests can be set at different lengths. (5) Arms can be adjusted in height. (6) Arms can be adjusted in width.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED PREPARATION FOR USE NOTE: Before using the Powerchair for the first time, be sure the batteries have been connected. Charge the Powerchair for at least 6-8 hours prior to first time use. NOTE! Maximum efficiency can only be achieved with sufficient battery power and adequate run-up distance. WARNING! Be aware that the angle of incidence should be approached around 90° to ensure safety and stability.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES FOOTREST ADJUSTMENTS (Fig. 9) STREAMER (888-WB/WAB/WSB) WIZZ (WNL) LENGTH (3) Pull out the safety pin (1) from the first hole in the footrest slide tube (2), adjust the footrest slide tube and refit the safety pin in the hole at the desired length. (2) (1) Fig. 9 ANGLE Release the lock nut and adjust the bolt under the footrest (3) to adjust the footrest angle. When the angle desired is reached, re-tighten the lock nut and bolt.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES FOOTREST ADJUSTMENTS (Fig. 11) JETSTREAM-L/M (888-WAL/WAM) (1) LENGTH Pull out the safety pin (1) from the first hole in the (2) footrest slide tube (2), adjust the footrest slide tube and refit the safety pin in the hole at the desired length. (3) ANGLE Fig. 11 Release the lock nut and adjust the bolt under the footrest (3) to adjust the footrest angle. When the angle desired is reached, re-tighten the lock nut and bolt.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED ADJUSTMENT PROCEDURES JOYSTICK CONVERSION (right to left or left to right) Beneath each of the arm pads there is a hand knob [Fig.10 (2)] used to adjust the length of the arm pad and secure the arm pad to the arm rest assembly. Remove the hand knob completely and slide off the arm pad. You can now exchange the joystick controller from one side to the other. SEAT HEIGHT ADJUSTMENTS (Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED OPERATION INSTRUCTIONS (7) (5) (4) (1) (2) (3) (8) (6) Fig. 14 GETTING READY TO KNOW THE JOYSTICK CONTROLLER (VSI 50) On / Off Button (1) This button turns the joystick controller (hereinafter referred to as 1 VSI) on and off. Do not use this button to stop the Powerchair, except in an emergency. Battery Gauge (2) This is a 10-segment display, which indicates if the VSI is switched 2 on and gives the state of charge of the battery.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED OPERATION INSTRUCTIONS Charging Port (8) for Off-Board Charger Only plug into this port with the qualified charger certified by the original manufacturer of the Powerchair. This port should not be used as a power supply for any other electrical devices. The behavior against the two statements as above will void the warranty of the Powerchair.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED DISASSEMBLY & ASSEMBLY INSTRUCTIONS COMPONENTS FOR WIZZ 888WNL (1) Reclining captain seat assembly with arm assembly. (1) (5) (2) (2) Chassis shroud. (3) Rear Chassis Assembly. (4) Batteries. (5) Front Chassis Assembly. (3) (4) Fig. 15 COMPONENTS FOR STREAMER 888WB/WAB/WSB (1) Captain seat assembly with (2) arm assembly. (2) Chassis shroud. (3) Chassis Assembly. (4) Batteries. (1) (4) (3) (5) Anti-tip Wheel Assembly. (5) Fig.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED DISASSEMBLY & ASSEMBLY INSTRUCTIONS DISASSEMBLY PROCEDURES WARNING! We advise caution when disassembling and lifting items. You must ensure that the person undertaking these actions is able to handle the weight. STEP 1 Ensure the area where the Powerchair is to be dismantled is spacious. STEP 2 Remove the plug at the end of the VSI cable by pulling on the pull ring. CAUTION! Lay the plug down carefully, taking care not to damage the chassis shroud.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED BATTERIES & BATTERY CHARGING BATTERIES The Powerchair is supplied with 2 x 33/34/36 Ah gel, sealed lead acid, maintenance free batteries. These are fitted under the seat in the center of the Powerchair. For easy handling, Velcro or plastic carrying straps are provided to assist in fitting or removal. The duration of the batteries can be affected by temperature, terrain and weight of the user. The Battery Gauge is a guide on the remaining charge in the batteries.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED BATTERIES & BATTERY CHARGING 1. Grasp the charging port cover and remove it from the charging port. 2. Plug AC power cord with female connector into the charging port shown as Fig.19. 3. Plug AC power cord with male connector into 110-volt wall outlet. NOTE! The voltage suitable for the charger is different from districts. Please assure to use the correct AC power cord for charging. 4.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED BATTERIES & BATTERY CHARGING BATTERY CHARGING FOR STREAMER-888WB & STREAMER-888WSB (UNITS EQUIPPED WITH OFF-BOARD CHARGER) To recharge the Powerchair, connect the charger to the Charging Port at the front of the VSI referred to as (8) in Fig. 14. Switch on the charger. Do not leave the charger plugged into the Charging Port if the charger is not charging. This charger is for indoor use only. Do not expose it to rain or water spray.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED TROUBLE SHOOTING The Self-Help Guide (Table 1) is intended to assist in the location of a fault that may occur in a certain part of the Powerchair. If after checking out the fault from the table below and the fault is still showing, do not use the Powerchair. Turn off the power and consult your provider immediately. Table 1 BATTERY GAUGE POSSIBLE FAULT 10 Bars flash Battery voltage is too high. Check the battery connections. 9 Bars flash Solenoid brake fault.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED TROUBLE SHOOTING LOCK MODE: The VSI controller can be locked to prevent unauthorized use. The locking method is achieved through a sequence of key presses and joystick movements, as detailed below. To lock Powerchair controller: While the controller is switched on, depress and hold the on/off button. After 1 second the controller will bleep. Now release the on/off button. Push the joystick forward until the controller bleeps.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED SPECIFICATION Table 2 ITEM Overall Length 888WB 1 888WAB 888WSB 888WNL 888WAL 888WAM Inches 35” 38” 36” 41” 40” 40” Overall Width Inches 22” 22” 24” 23” 26.7” 26.7” Overall Height Inches 37” 40” 39” 42” 40” 36” Lbs 134 172 172 203 216 205 Battery Weight Lbs*pcs 23 lbs*2 23 lbs*2 26.4 lbs*2 23 lbs*2 34.7*2 34.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED QUARTERLY INSPECTION For your own safety, quarterly inspection and service on the product with signature by an authorized dealer is strongly recommended. Maintenance records (Table 3) should be kept at all times. The manufacturer / distributor / vendor will be indemnified from any product liability claim if the above maintenance / service requirement is not met.
GMP ISO9001 ISO14001 ISO13485 CERTIFIED CONTENTS ~29~
GMP ISO9001 ISO14001 ISO13485 CERTIFIED CONTENTS ~30~
GMP ISO9001 ISO14001 ISO13485 CERTIFIED CONTENTS ~31~
GMP ISO9001 ISO14001 ISO13485 CERTIFIED DISCLAIMER Congratulations on your purchase of this Powerchair. This Powerchair is not intended to be used by individuals with physical limitations that could prevent the user from operating the Powerchair safely. disclaims all responsibility for any personal injury or property damage, which may occur as a result of improper or unsafe use of its products. Mechanical or electrical defects will be dealt with on a contingency liability basis.
