Product Instructions

A
Laser Light Projector
B
Ground Stake
C
Adapter
D
Remote
A
B
C
D
1
1
1
1
Mode Button
Button
Laser
Holder
Ground Stake
LASER RADIATION,
AVOID DIRECT EYE EXPOSURE,
DO NOT STARE INTO BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS,
CALSS IIIa LASER PRODUCT
MAX OUTPUT<5 mW
WAVELENGTHS 520-650 NM
Version: 2019
www.ishowtree.com
Scan & See Me!
PACKAGE CONTENTS PRODUCT INSTRUCTIONS
BUTTON FUNCTION
REMOTE CONTROL
REMOTE CONTROL SAFETY INSTRUCTIONS
PRODUCT INSTRUCTIONS
Screw the stake into the holder to secure the projector.
1
Plug power cord into socket, unplug when not in use.
3
Connect adapter as figure shows.
2
PRODUCT SPECIFICATION
Laser Classification: Class llla
Laser Wavelength:
Red 635 nm, Green 532 nm
Power: UL &CUL Adapter 5V, 2A
Operation: Indoor/Outdoor
Operating Temperature:
-15° F to 90° F (-26° C to 32° C)
Projection Coverage: 30 ft x 30 ft
Cord Length 3ft
Warranty: One Year Limited
1. Remove insulating tape from the battery compartment before use.
The max receiving distance of this remote is 8 meters.
2. button: turn on/off.
3. button: turn to Default Settings:
Steady on Red & Green, 6H On /18H Off.
4. button: switch the red laser On/Off.
button: switch the green laser On/Off.
5. button: switch to Steady, flash.
6. button: setting timer function.
button: set timer, 2H On / 22H Off;
button: set timer, 4H On / 20H Off;
button: set timer, 6H On / 18H Off;
button: set timer, 8H On / 16H Off;
button: cancel timer settings.
If the remote control does not work, check battery.
WARNING: This is not a toy and is not intended for use by children.
(A) Do not dispose of the battery in fire as the battery may leak and
explode.
(B) Do not mix old and new batteries and not mix alkaline, standard
(carbon-zinc), or rechargeable(nickel-cadmium)batteries.
(C) Exhausted batteries are to be removed from the product.
(D) Dispose of battery properly by following directions on battery.
(E) Use CR2025 battery only. Use of other batteries may damage
remote control
(F) Safe for indoor use.
(G)Do not expose the Remote Control to moisture.
Battery installation:
1. Slide battery cover off.
2. Insert a "CR2025(3 volt)battery.
1. Connect the power adapter to the laser light projector.
The adapter input voltage is AC120V.
2. Press the button to switch mode/turn on.
3. Press and hold the button to turn off.
4. Built-in timer function: 6h On /18h Off.
Insulating Tape
1. Press and hold the button to turn off.
2. Press the button to switch to the preferred
mode as below:
·Steady on Red
·Steady on Green
·Steady on Red & Green
·Red Flashing
·Green Flashing
·Red & Green Flashing
3. Memory function: While power-off, short
press the button to turn on and get back
to the mode of last use.
Safety Attention
1. Turn off 30 minutes after working 6 hours to keep the lifetime
of product.
2. This product is mainly used for outdoor with waterproof Ip44.
It has excellent radiating ease. Keep it far away from the flammable
objects or liquids.
3. Please use show light laser projector power adapter to support the
light. If you need to change a new adapter, please check the
parameter of our adapter before you buy a new one.
CAUTION
1. Danger-laser radiation when open.
2. Avoid direct exposure to beam.
3. Avoid direct eye exposure.
4. Laser radiation-do not stare into beam or view directly with
optical instruments.
5. The use of optical instruments with this product will increase
eye hazard.
6. Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
IMPORTANT!
Do not point the show light laser projector close to the airplane
or up in the sky.
FEDERAL COMMUNICATIONS COMMISSION (FCC)
STATEMENT
PART DESCRIPTION QUANTITY
FCC Caution
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority
to operate the equipment.
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
*RF warning for Mobile device:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your body.