MANUAL ENGLISH Infinity iS-200 Ordercode: 41501 Highlite International B.V.
Infinity iS-200 Table of contents Warning ...............................................................................................................................................................................2 Safety Instructions .........................................................................................................................................................2 Operating Determinations ............................................................................................
Infinity iS-200 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
Infinity iS-200 IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the nonobservance of this manual or any unauthorized modification to the device. ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never remove warning or informative labels from the unit. Never use anything to cover the ground contact.
Infinity iS-200 Operating Determinations ● ● ● ● ● ● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The minimum distance between light-output and the illuminated surface must be more than 1 meter. The maximum ambient temperature ta = 40°C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
Infinity iS-200 Mounting a clamp to the underside of the Infinity moving head Improper installation can cause serious damage to people and property ! Ordercode: 41501 5
Infinity iS-200 Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place.
Infinity iS-200 Description of the device Features The Showtec Infinity iS-200 LED Spot is a moving-head with high output and great effects. ● On-Board: Battery powered full color display including gravity sensor ● It has a rotating 3 facet prism as well a frost filter, which makes it possible to use the fixture also as a true wash light ● Quick lock screws on the covers allow you to change gobos within minutes without the need of any special tools ● LED source the shutter is electronic not mechanical.
Infinity iS-200 Overview Fig. 01 01) Lens 02) Menu Buttons + LCD Display Backside Fig. 02 03) 04) 05) 06) 07) 08) 09) 10) DMX signal connector (IN) 5-pin DMX signal connector (OUT) 5-pin DMX signal connector (IN) 3-pin DMX signal connector (OUT) 3-pin Neutrik Powercon IN Neutrik Powercon OUT ON/OFF Fuse F7AL 250V NOTE: Knowledge of DMX is required to fully utilize this unit.
Infinity iS-200 Installation Remove all packing materials from the Infinity iS-200 LED Spot. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. Damages caused by non-observance are not subject to warranty. Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode.
Infinity iS-200 Multiple Infinity’s (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. 04) Use a 3-p XLR cable to connect the Infinity’s and other devices.
Infinity iS-200 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Important: Fixtures on a serial data link must be daisy chained in one single line.
Infinity iS-200 Control Panel A) B) C) D) E) F) G) H) I) J) K) Home button Edit Menu button Settings Mode Button Address Setting Button Infinity Logo Button Up Button Down Button OK/ENTER Left Button Right Button LCD Display Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.
Infinity iS-200 Menu Overview Ordercode: 41501 13
Infinity iS-200 Main Menu Options DMX address Edit Mode Settings Menu Built-in Programs Test Mode Info Home Up Edit Menu Down Setting Mode OK Address Setting Left Infinity Logo Right 1. DMX Addressing With this menu you can set the DMX address. 01) Press the button and select . 02) Press the button, to confirm. You can choose 512 different DMX addresses.
Infinity iS-200 2. Edit Mode With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm. You can choose 3 different modes. Use the Up / Down buttons to select the required mode: 03) Once you have selected the desired mode, press the No to YES. buttons to change the value from 04) Once you have selected the desired setting, press the button to store your settings.
Infinity iS-200 4. Built-in Programs With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm. You can choose 10 different modes. Use the Up / Down buttons to select the required mode: 03) Once you have selected the desired mode, press the No to YES. 04) Once you have selected the desired setting, press the Ordercode: 41501 16 buttons to change the value from button to store your settings.
Infinity iS-200 5. Test Menu With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm. You can choose 2 different modes. Use the Up / Down buttons to select the required mode: 03) Once you have selected the desired mode, press the buttons to change the value from No to YES. 04) If you press the OK button at the Reset function, a new Menu will open. 05) You can set 21 different Test options.
Infinity iS-200 6. Information Menu With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm.
Infinity iS-200 DMX Channels 21 Channels (Advanced) Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 – Vertical movement (Tilt) Push the slider, up in order to move head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
Infinity iS-200 Channel 9 – Colourwheel 1 Linear color change following the movement of the slider. Between 128 - 255, the color-wheel rotates continuously the so-called “Rainbow” effect.
Infinity iS-200 Channel 11 – Rotating Gobo-wheel + Gobo Shake 0-7 Open / White 8-15 Gobo 1 (Glass) 16-23 Gobo 2 (Metal) 24-31 Gobo 3 (Metal) 32-39 Gobo 4 (Metal) 40-47 Gobo 5 (Metal) 48-55 Gobo 6 (Metal) 56-63 Gobo 7 (Metal) 64-71 Gobo Shake 7 from slow to fast 72-79 Gobo Shake 6 from slow to fast 80-87 Gobo Shake 5 from slow to fast 88-95 Gobo Shake 4 from slow to fast 96-103 Gobo Shake 3 from slow to fast 104-111 Gobo Shake 2 from slow to fast 112-119 Gobo Shake 1 from slow to fast 120-127 Open / White 12
Infinity iS-200 Channel 14 – Prism 0-4 Open 5-255 3-facet Prism Effect, Channel 15 – Prism rotation 0-127 Prism-indexing 128-189 Clockwise rotation (CW) from slow to fast 190-193 Stop 194-255 Counter-clockwise rotation (CCW) from slow to fast Channel 16 – Iris 0-63 Iris from big to small 64-127 Auto Zoom from slow to fast 128-191 Zoom in slowly, zoom out fast 192-255 Zoom in fast, zoom out slowly Channel 17 – Focus 0-255 Continuous adjustment from far to near Channel 18 – Frost Effect 0-255 Frost Effect Cha
Infinity iS-200 Channel 20 – Built-in Programs 0-7 No Function 8-15 Built-in Program 1 16-23 Built-in Program 2 24-31 Built-in Program 3 32-39 Built-in Program 4 40-47 Built-in Program 5 48-55 Built-in Program 6 56-63 Built-in Program 7 64-71 Built-in Program 8 72-79 Built-in Program 9 80-87 Built-in Program 10 88-95 Built-in Program 11 96-103 Built-in Program 12 104-111 Built-in Program 13 112-119 Built-in Program 14 120-127 Built-in Program 15 128-135 Built-in Program 16 136-143 Built-in Program 17 144-15
Infinity iS-200 18 Channels (Basic) Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 – Vertical movement (Tilt) Push the slider, up in order to move head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
Infinity iS-200 Channel 9 – Colourwheel 2 Linear color change following the movement of the slider. Between 128 - 255, the color-wheel rotates continuously the so-called “Rainbow” effect.
Infinity iS-200 Channel 11 – Gobo rotation 0-63 Gobo-indexing 64-147 Clockwise rotation (CW) from slow to fast 148-231 Counter-clockwise rotation (CCW) from slow to fast 232-255 Gobo bouncing Channel 12 – Static Gobo-wheel + Gobo Shake 0-6 Open / White 7-13 Gobo 1 14-20 Gobo 2 21-27 Gobo 3 28-34 Gobo 4 35-41 Gobo 5 42-48 Gobo 6 49-55 Gobo 7 56-63 Gobo 8 64-71 Gobo Shake 8 from slow to fast 72-78 Gobo Shake 7 from slow to fast 79-85 Gobo Shake 6 from slow to fast 86-92 Gobo Shake 5 from slow to fast 93-99 Go
Infinity iS-200 Channel 18 – Channel Functions 0-7 No Function 8-14 Blackout during Pan/Tilt movement 15-23 Blackout during Colorwheel movement 24-31 Blackout during Gobowheel movement 32-39 Blackout during Pan/Tilt/Colorwheel movement 40-47 Blackout during Pan/Tilt/Gobowheel movement 48-55 Blackout during Pan/Tilt/Gobowheel /Colorwheel movement 56-87 No Function 88-95 No Function 96-103 Reset Pan after 3 seconds 104-111 Reset Tilt after 3 seconds 112-119 Reset Colorwheel after 3 seconds 120-127 Reset Gobow
Infinity iS-200 Maintenance The Showtec Infinity iS-200 LED Spot requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents.
Infinity iS-200 Fig. 08 03) 04) 05) 06) Loosen the service lid of the housing, by sliding it to the bottom. Gently tilt the head so the small metal housing will slide out more easy. Turn the gobo wheel, with the gobo you want to remove, to the upside. Gently lift up the gobo holder 10º and then gently pull out the gobo from its position. Fig. 09 07) Very carefully take the gobo out of the gobo holder with a pair of pliers. 08) Place the new gobo in the gobo holder.
Infinity iS-200 Colorwheel 1 Colorwheel 2 Fig. 10 Fig. 11 Rotating Gobo-wheel Static Gobo-wheel Fig. 12 Ordercode: 41501 Fig.
Infinity iS-200 Battery Replacement (must be carried out by a qualified technician!) 01) 02) 03) 04) 05) 06) 07) Unplug the unit from the electric power source. Remove the 6 screws on the front side of the Infinity. Gently pull the front cover from the device. Disconnect the plug from the PCB. Remove the 2 screws holding the battery pack in place. Replace the old battery pack with a new one. Replace the maintenance cap and fasten all screws. Fig.
Infinity iS-200 Troubleshooting No Light This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps. If the light effect does not operate properly, refer servicing to a technician. Response: Suspect four potential problem areas as: factory reset, the power supply, the LED, the fuse.
Infinity iS-200 Problem Probable cause(s) Remedy One or more fixtures are completely dead. No power to the fixture. ● Check that power is switched on and cables are plugged in. Primary fuse blown. ● Replace fuse. Fixtures reset correctly, but all respond erratically or not at all to the controller. The controller is not connected. 3-pin XLR Out of the controller does not match XLR Out of the first fixture on the link (i.e. signal is reversed). ● ● Connect controller.
Infinity iS-200 Product Specification Model: Input Voltage: Continuous Power: Fuse: Dimensions: Weight: Showtec Infinity iS-200 LED Spot 100-240 VAC 370W max.
Infinity iS-200 Gobos Colourwheel: Max. ambient temperature ta: Motor: heat-resistant and intensify glass; dichroic glas coating 40°C; Max. housing temperature tB: 80°C high quality stepping-motor controlled by microprocessors Minimum distance: Minimum distance from flammable surfaces: Minimum distance to lighted object: 0.5m 1.3m Design and product specifications are subject to change without prior notice. Website: www.Showtec.info Email: service@highlite.
Infinity iS-200 Dimensions Ordercode: 41501 36
Infinity iS-200 Notes Ordercode: 41501 37
Infinity iS-200 Ordercode: 41501 38
©2014 Showtec
