Scanmaster 2 MKII ORDERCODE 50333
Congratulations! You have bought a great, innovative product from Showtec. The Showtec Scanmaster 2 MKII brings excitement to any venue. Whether you want simple plug-&-play action or a sophisticated DMX show, this product provides the effect you need. You can rely on Showtec, for more excellent lighting products. We design and manufacture professional light equipment for the entertainment industry. New products are being launched regularly. We work hard to keep you, our customer, satisfied.
Showtec Showtec Scanmaster 2 MKII™ Product Guide Warning..…...................................................................................…………………………………………. Safety-instructions………………………………………………………………………………………….…. Operating Determinations……………………………………………………………………………………. 2 2 3 Description..…..............................................................................……….………………………………… Features…….……………………………………………………………………………………….……...…. Overview……………………………………………………………………………………………………….. Back side..
WARNING CAUTION! Keep this device away from rain and moisture! FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! SAFETY INSTRUCTIONS Every person involved with the installation, operation and maintenance of this device has to: be qualified follow the instructions of this manual CAUTION! Be careful with your operations.
• • • • • • • If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. If your Showtec device fails to work properly, discontinue use immediately. Pack the unit securely (preferably in the original packing material), and return it to your Showtec dealer for service.
Description of the device Features The Scanmaster 2 MKII is a lightcontroller from Showtec.
1) FIXTURE buttons (1-12) To select fixtures for setting, programming or recording. 2) SCENE buttons (1-8) Press the scene buttons to load or store relevant Scenes. There is a maximum of 240 programmable scenes. 3) Channel faders (1-8) These faders control the dimming output of each corresponding channel. 4) Channel Bank button To switch between Ch 1-8 and Ch9~16. 5) Speed fader To adjust the speed level (0.1 second -10 minutes). 6) FADE TIME fader Used to adjust the fade time (0~30seconds).
Backside Fig. 2 21) AUDIO LINE INPUT 0.1V~1Vp-p 22) DB-9 Connector To connect an external step controller 23) MIDI IN Used to receive MIDI data. 24) Fog Machine Output To send the signal to a fog machine. 25) DMX OUT This connector sends your DMX value to the DMX scanner or DMX pack 26) DC INPUT DC 9 ~15V, 500mA min. 27) POWER ON / OFF Used to switch on / off the power. Installation Remove all packing materials from the Scanmaster 2 MKII. Check that all foam and plastic padding is removed.
SCENES When powered on, this unit will first be in Manual control mode, and all channel outputs are in black-out state (the Blackout LED flashes in the display window). You can also press the Blackout button to enable the channel output. Press and hold down the PROGRAM button (15) for 3 seconds till the PROG LED flashes, this means you have entered the programming mode. Press and again hold down the PROGRAM button (15) for 3 seconds (till the PROG LED goes out) to exit from the Programming mode.
Editing a scene 1) Enter program mode. 2) Press the BANK Up/Down button (11) to select the bank containing the scene you wish to edit. 3) Select the scene you wish to edit by tapping its SCENE button (2). 4) Use the faders and/or joystick to make the desired adjustments to the scene. 5) Once you have completed the changes, tap the MIDI/Rec button (17). 6) Tap the SCENE button (2) that corresponds to the scene you're editing. This will override the existing scene.
Scene Playback There are 3 ways to start scene playback: manual trigger, auto trigger or audio trigger. 1. Manual trigger 1) When the power is turned on, the unit automatically enters Manual mode, and all channel outputs are in black-out state (the Blackout LED flashes in the display window). 2) Tap the BLACKOUT button (20) to enable the channel output. Blackout LED goes out.
CHASES Programming a Chase Note: You must have already programmed scenes in order to program a chase. This function allows you to cycle through 12 programmable chases, with up to 240 scenes each, in a preselected order. It is recommended to delete all chases in the controller, before programming chases for the first time. Also see Delete All Chases for instructions. 1) Enter program mode. 2) Tap the CHASE button (14) to select the chase you wish to program. Its LED will lit.
Chase Playback There are 3 ways to start chase playback: manual trigger, auto trigger or audio trigger. 1. Manual trigger 1) When the power is turned on, the unit automatically enters Manual mode, and all channel outputs are in black-out state (the Blackout LED flashes in the display window). 2) Tap the BLACKOUT button (20) to enable the channel output. Blackout LED goes out. 3) Tap your selected CHASE button (14), its LED will be lit. Then use the FADE TIME fader (6) to adjust the running state.
4) Press the TAP/Display button (19) to change between the 8 Channel or 16 Channel mode. 5) Press the FIXTURE button (1) to select the scanner. 6) While holding the MODE button (8), press the corresponding SCENE button (2) for the channel you wish to reverse. (For Example: If you are reversing the one fixture, once you verify that you are in reverse mode, and the Tilt LED is lit, check to see which slider the Tilt control is on.
MIDI Control MIDI Channel Setting 1) Press and hold down the MIDI button (17) for 3 seconds. The display may show you: "ln:01". This means the current Midi channel is "01". 2) Use the BANK Up/Down button (11), to select the DMX channel 01 -16 you wish to assign to the MIDI channel. 3) Press and hold the MIDI button (17) for 3 seconds to save your setting, all the LEDs will flash briefly, indicating your operation has been saved. 4) Press BLACKOUT button (20) to exit.
FILE TRANSFER File Transfer allows the user to transfer all information stored in one Scanmaster 2 MKII to a second Scanmaster unit. You must connect the units using 3-pin XLR cables. The unit sending the information will have the cable plugged into the DMX Out plug, and the receiving the information will have the cable running into the DMX In location. Before data sending, make sure the connections between this unit and the connected DMX receiver are OK.
Maintenance The Showtec Scanmaster 2 MKII requires almost no maintenance. However, you should keep the unit clean. Disconnect the mains power supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. Do not use alcohol or solvents. Keep connections clean. Disconnect electric power, and then wipe the DMX and audio connections with a damp cloth. Make sure connections are thoroughly dry before linking equipment or supplying electric power.
Product Specification Model: Showtec Scanmaster 2 MKII Voltage: AC 230V-50Hz (CE) Power input: DC9 ~ 12V, 500 mA min. Internal Fuse: 500mA250V, 5x20mm Audio trigger: Built-in Mic DMX Output: 3-pin XLR Female connector Midi Input: 5-pin connector Sound Input: RCA connector EXT STEP Control: DB-9 connector Dimensions: 483 x 135 x 82 mm (LxWxH) Weight: 2,7 kg Design and product specifications are subject to change without prior notice.
2005 Showtec.
