WDV8000 User’s Manual 1
Foreword Thank you for purchasing this WiFi video camera. It has an elegant appearance, many functions and can be used for wide-angle shooting. Prior to use, please read this user’s manual carefully so as to show its performance and extend its service life to maximum. We hope that this product can meet your needs and accompany you at your side all the time.
System Requirements PCCAM Operating System MSDC CPU Internal Memory Sound Card and Display Card CD Driver Hard Disk Others System Requirements Microsoft Window XP(SP3), Vista, 7，8 Mac OS X ver: 10.8.0 or above version Microsoft Window 2000，XP, Vista, 7，8 Mac OS X ver: 10.0.0 or above version Intel Pentium of more than 1GB Hz or other CPU with equivalent performance Larger than 1GB The sound card and video card shall support DirectX8 or higher version.
Introduction to appearance and keys Lens Infrared remote control lamp Charging /Busy indicator Busy indicator Display/Menu key 2.
Power/Mode key Shutter/OK key Battery door Speaker Wifi/Down key Micro SD Card Micro USB port HDMI port 5
Start using _______ 1. Charge the built-in lithium battery USB cable Connect the camera to the computer for charging, at this time, the charging indicator will be in red, and it will be off after charging. Generally, it takes 2-4 hours to charge the battery.
2. Use the storage card 1. Push the TF card into the slot till it is in place as per the instruction in concavely engraved words by the storage card slot. 2. To take out the TF card, press the tail of the storage card inwardly softly and it will be popped out. Note: There’s no built-in memory unit in the camera, so make sure to insert a storage card into it prior to use (it is recommended that a TF card of better quality be used).
3. Power on/off 3.1 Power on: Press Power key for 3 seconds, the screen will be on and the camera will be started. 3.2. Power off: Hold on Power key for 3 seconds when the camera is in the idle state to turn it off. 3.3. Auto screen off: The screen will be turned off automatically when the time that the camera is in the idle state for automatic screen off to save power. After that, the lamp for screen off will be on. 3.4. Power off when the camera is lack of electricity.
Video recording mode Car-carrying mode Replay mode 9 Shooting mode
5. Indicator Busy indicator (red): When the camera is busy such as recording videos, shooting photos and turning off screen automatically, the work indicator will flicker. Charging indicator (blue): When it is on, the user is prompted that the camera is being charged and it will be off after charging is completed. 6.
7. Car-carrying mode After power is on, press Power key to enter car-carrying mode 1. Icon of mode, indicating car-carrying mode; 2. Indicate quality of video; 3. Indicate size of video:1440P (30FPS)/FHD 1080P(60FPS) / HD 720P(120FPS) / HD 720P(60FPS) is optional. 4. Recording time, indicating recordable length of time. 5. Icon of battery, indicating current electrical quantity Prompt: In car-carrying mode, a passage of video is kept every three minutes in recording.
9. Replay mode 9.1 After power is on and entering Preview state, press Power key continuously to shift to Replay mode. Select the file to be replayed through the menu as follows: Select CAR to replay files in car-carrying video mode; Select VIDEO to replay files in general video mode; Select JPG to replay files in shooting mode; 9.2 Introduction to play screens 9.2.
1. Icon of replay mode; 2. Indicate serial number of current file/ total number of files; 3. Indicate parameter of recording time; 4. Operation buttons hint icon 5. Indicate recording time point. When a video file is being played, click Ok key to pause play, and click Menu key to stop playing. 9.2.2 Screen of photos 1. Indicate serial number of current file/ total number of files; 2. Operation buttons hint icon In replaying, Press WIFI key to select other file type， in a circulating way.
10. Menu operation There is a different menu in each working mode as shown in the following figures: Menu for video recording /car-carrying mode Menu for shooting mode Menu for setting mode Menu for replay mode Operation: Press Menu key, the menu for this mode will be displayed on the LCD. At this time, press Power key to move the cursor leftward or rightward and select on the menu, and press WIFI key to move the cursor upward or downward and select on the menu in a circulating way.
Application of remote controller 1. Definition of keys of remote controller Signal transmission port Keys of remote controller are as shown Power on/off key in the right figure: Video recording key Shooting key 2. Use of remote controller: Using the remote controller, you can achieve functions of power on, video recording, shooting and power off without operating on the camera.
Connect device to HDTV: Connect the video camera to an HDTV with a HD cable as shown in the following figure, display signals in the camera will be output into the HDTV automatically, and you can browse HD videos and photos that are recorded or taken in the HDTV.
APP (for Android and iOS System) I. How to Obtain the APP Installation Program 1. For the Android System, you can search “SYMAGIX2” in the Play Store to obtain corresponding installation programs, and then you can install them according to the indicated steps or through scanning the two-dimensional code. 2.
and the Screen of the Camera will show the WIFI signal Icon with the external screen revealing WIFI Connecting. 3. Enable the WIFI function of the Android mobile phone or tablet PC, and try to find the AP Name WDV8000; please conduct connection between them till the system reveals a successful connection; Note：if you are conducting WIFI connection for the first time, please input the password: 1234567890. 4.
IOS Applications 1. Please install the SYMAGIX2 application program (provided by the Supplier or the Internet) for the IOS ; mobile phone or tablet PC, and then the Display Screen will show the Icon 2. Insert a Storage Card into the Camera and then power it on. Press the WIFI key to conduct WIFI connection, and the Screen of the Camera will show the WIFI signal Icon with the external screen revealing WIFI Connecting. 3.
1 2 3 4 1. DV battery icon 2. Video resolution 3. White balance 4. Setup (enter setup menu) 9 5. Enter Playback mode 6. Timelaps Mode 7. Photo mode 8. Video mode 9. Shutter button 5 6 7 8 Notes: 1. If you need to record videos or download pictures using your mobile phone or tablet PC, please insert one TF card for your camera; 2. When the Camera has been successfully connected with your mobile phone or tablet PC, the WIFI Indicator Light will be on.
Application on PC 1. The camera has a plug-and-play function. Connect the power-on device to the computer with the USB cable, and the mode can be automatically switched to the removable hard disk. Removable disk icon will appear in the "My Computer" window. The pictures you shot stored in the removable disk I: \ jpg folder (I is this equipment removable disk); video files your shot stored in I: \ video folder; vehicle-mounted files you shot saved in I: \ CAR folder.
Technical Parameters Image Sensor 8.0 Million Image Sensor Function Modes Video recording mode, car-carrying mode, shooting mode and replay mode Lens F2.8, f=2.5mm LCD Display Screen 2.0 inch HD LCD Screen Photo Definition Ratio Video Definition Ratio 16M 、8M、5M 、4M 1440P 1920x1440(30fps)、 FHD：1920x1080(60fps）、 FHD：1920x1080(30fps）、HD：1280x720（120fps）、 HD：1280x720（60fps） Storage Media TF Card (32GB at most) File Formats Videos(MOV); H.264 Compressed Format;Photos(JPG) USB Port USB 2.
Label Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
